The damper servo sub-assembly (mode damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1443/43 | The air outlet damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (mode damper servo). | ·
Damper servo sub-assembly (mode damper servo) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
| Result | Proceed to |
|---|---|
| DTC B1443/43 is not output | A |
| DTC B1443/43 is output | B |
| DTC B1443/43 and B1497/97 are output | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Use the Data List to check if the damper servo sub-assembly (mode damper servo) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Outlet Servo Pulse (D) | Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255 | 15 (pulse): FACE 1
23 (pulse): FACE 2 41 (pulse): B/L 65 or 73 (pulse): FOOT 83 or 95 (pulse): F/D 113 (pulse): DEF |
- |
| Air Outlet Servo Actu Pulse (D) | Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255 | 15 (pulse): FACE 1
23 (pulse): FACE 2 41 (pulse): B/L 65 or 73 (pulse): FOOT 83 or 95 (pulse): F/D 113 (pulse): DEF |
- |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| OK (When troubleshooting according to the DTC) | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| Both target pulse and actual pulse do not display | C |
| Target pulse displays normally, but actual pulse does not display | D |
A
B
C
D
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1443 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Replace the damper servo sub-assembly (mode damper servo) (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY).
Since the damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (mode damper servo) with a new or normally functioning one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1443 is not output.
OK
NG
Temporarily replace the air conditioning harness assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY).
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1443 is not output.
OK
NG