Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

E346100E01
0.135,0.094 1.969,0.292 1.833,0.198 10 false Blower Level 2.667,1.313 3.813,1.51 1.146,0.198 10 false Duty Ratio (%) = 4,1.427 4.25,1.625 0.25,0.198 10 false T2 1.219,2.385 2.083,2.583 0.865,0.198 10 false SI Duty (%) 4,1.146 4.25,1.344 0.25,0.198 10 false T1 4.667,1.281 5,1.479 0.333,0.198 10 false 100 6.031,0.729 6.281,0.927 0.25,0.198 10 false T1 6.167,1.719 6.417,1.917 0.25,0.198 10 false T2 5.5,1.063 5.75,1.26 0.25,0.198 10 false Off 5.51,1.354 5.76,1.552 0.25,0.198 10 false On 0.656,2.115 0.906,2.313 0.25,0.198 10 false 0 1.198,2.135 1.615,2.333 0.417,0.198 10 false Low 2.094,2.135 2.51,2.333 0.417,0.198 10 false High 0.5,1.5 0.75,1.698 0.25,0.198 10 false LO 0.552,1.052 0.802,1.25 0.25,0.198 10 false M 0.563,0.573 0.813,0.771 0.25,0.198 10 false HI

The blower with fan motor sub-assembly operates according to signals from the air conditioning amplifier assembly. The blower with fan motor sub-assembly speed signals are transmitted by changes in the duty ratio.

Duty Ratio:

The duty ratio is the ratio of the blower with fan motor sub-assembly on time (T1) to the total of the blower with fan motor sub-assembly on and off time (T2).

The air conditioning amplifier assembly controls the blower with fan motor sub-assembly speed.

WIRING DIAGRAM

E198319E17
1.083,0.74 1.469,1.021 0.385,0.281 10 false SI 1.052,1.656 1.479,1.958 0.427,0.302 10 false +B 0.927,2.292 1.563,2.573 0.635,0.281 10 false GND 1.344,0.604 1.573,0.813 0.229,0.208 10 false 2 1.344,1.552 1.573,1.76 0.229,0.208 10 false 3 1.344,2.167 1.573,2.375 0.229,0.208 10 false 1 0.208,2.875 0.958,3.188 0.75,0.313 10 false G26 0.198,3.042 1.625,3.708 1.427,0.667 10 false Blower with Fan Motor Sub-assembly 3.271,1.677 4.615,2.125 1.344,0.448 10 false from Battery 5.542,0.573 5.875,0.833 0.333,0.26 10 false 23 5.552,2.198 5.875,2.458 0.323,0.26 10 false 14 5.896,0.729 6.375,0.979 0.479,0.25 10 false BLW 5.896,2.344 6.531,2.656 0.635,0.313 10 false GND 5.583,2.854 6.094,3.083 0.51,0.229 10 false G25 5.573,3.01 7.125,3.781 1.552,0.771 10 false Air Conditioning Amplifier Assembly 2.25,1.813 2.781,2.115 0.531,0.302 10 false HTR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BLOWER WITH FAN MOTOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the blower with fan motor sub-assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Blower Motor Blower with fan motor sub-assembly Min.: 0, Max.: 31 -

OK:

Blower with fan motor sub-assembly operates and blower motor speed changes.




OK

NG

2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BLOWER WITH FAN MOTOR - BATTERY AND BODY GROUND)
a.
U170580E02
2.073,1.594 2.198,1.896 2.198,1.896 2.354,1.896 false 1.406,1.604 1.188,1.896 1.188,1.896 1.021,1.896 false 2.073,1.594 2.198,1.896 2.198,1.896 2.354,1.896 true 1.406,1.604 1.188,1.896 1.188,1.896 1.021,1.896 true 0.104,0.01 0.281,0.167 0.177,0.156 10 false *a 0.5,1.146 0.802,1.313 0.302,0.167 10 false G26 2.406,1.813 2.708,1.979 0.302,0.167 10 false +B 0.677,1.823 1.188,1.99 0.51,0.167 10 false GND

Disconnect the G26 motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-3 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G26-1 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blower with Fan Motor Sub-assembly)


OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BLOWER WITH FAN MOTOR AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BLOWER WITH FAN MOTOR AND BODY GROUND)
a.

Disconnect the G25 amplifier connector.


b.

Disconnect the G26 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G25-23 (BLW) - G26-2 (SI) Always Below 1 Ω
G25-23 (BLW) - Body ground Always 10 kΩ or higher
G25-14 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (BLW SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (BLW SIGNAL)
a.
U149214E01
0.163,0.162 0.347,0.332 0.184,0.170 10 *a 1.581,0.322 1.895,0.487 0.313,0.165 10 G25 0.496,0.46 0.846,0.606 0.350,0.147 10 GND 2.886,3.886 3.236,4.033 0.350,0.147 10 GND 2.312,2.05 2.662,2.196 0.350,0.147 10 BLW 1.362,1.376 0.889,0.619 false

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Terminal No. (Symbol) G25-23 (BLW) - G25-14 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition Ignition switch ON
Blower switch LO

OK:

Waveform is as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

HINT:

Waveform varies with the blower level.




OK

5.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.CHECK BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Replace the blower with fan motor sub-assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>REMOVAL).


b.

Operate the blower with fan motor sub-assembly to check that it functions properly.

OK:

Blower with fan motor sub-assembly operates normally.




OK

END (BLOWER WITH FAN MOTOR SUB-ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY