Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261170 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1417  Evaporator Temperature Circuit  


DESCRIPTION

The No. 2 air conditioning harness assembly (rear evaporator temperature sensor) is installed on the evaporator in the rear air conditioning unit to detect the cooled air temperature that has passed through the evaporator and to control the rear air conditioning. It sends signals to the air conditioning amplifier assembly. The signals change in accordance with the resistance of the No. 2 air conditioning harness assembly (rear evaporator temperature sensor). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases. The air conditioning amplifier assembly applies a voltage (5 V) to the No. 2 air conditioning harness assembly (rear evaporator temperature sensor) and reads voltage changes as the resistance of the No. 2 air conditioning harness assembly (rear evaporator temperature sensor) changes. This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1417 Open or short in the No. 2 air conditioning harness assembly (rear evaporator temperature sensor) circuit.
·

No. 2 air conditioning harness assembly (rear evaporator temperature sensor)

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E196917E03
5.397,0.823 5.771,1.004 0.374,0.181 10 TEC 5.397,1.431 5.835,1.612 0.438,0.181 10 SGND 0.691,2.212 3.284,2.402 2.594,0.190 10 No. 2 Air Conditioning Harness Assembly 0.99,1 3.343,1.192 2.353,0.192 10 Rear Evaporator Temperature Sensor 5.16,0.744 5.316,0.925 0.156,0.181 10 4 5.119,1.348 5.290,1.529 0.171,0.181 10 19 4.221,1.344 4.377,1.525 0.156,0.181 10 7 4.206,0.739 4.362,0.920 0.156,0.181 10 8 4.043,0.735 4.199,0.916 0.156,0.181 10 + 4.048,1.367 4.204,1.548 0.156,0.181 10 - 0.691,2.067 0.995,2.255 0.304,0.188 10 Q13 5.269,2.034 5.586,2.189 0.318,0.156 10 G24 5.264,2.191 6.951,2.540 1.687,0.349 10 Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (REAR EVAPORATOR TEMPERATURE SENSOR)
a.

Use the Data List to check if the rear evaporator temperature sensor is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Ambient Temp Sens (Rear) Rear evaporator temperature sensor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual rear evaporator temperature displayed Open in the circuit: -29.7°C (- 21.46°F).
Short in the circuit: 59.55°C (139.19°F).

OK:

The display is as specified in the normal condition column.



Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C


A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT NO. 2 AIR CONDITIONING HARNESS ASSEMBLY (REAR EVAPORATOR TEMPERATURE SENSOR)
2.INSPECT NO. 2 AIR CONDITIONING HARNESS ASSEMBLY (REAR EVAPORATOR TEMPERATURE SENSOR)
a.

Remove the No. 2 air conditioning harness assembly (rear evaporator temperature sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR EVAPORATOR TEMPERATURE SENSOR>REMOVAL).

E346097E01
0.333,0.917 0.469,0.583 0.469,0.583 0.75,0.583 true 1.583,1.656 1.917,1.656 true 1.698,2.083 1.875,2.083 1.875,2.083 2.063,1.688 true 4,1.333 4.135,1 4.135,1 4.417,1 true 0.833,0.469 1.146,0.667 0.313,0.198 10 false *a 1.469,1.573 1.781,1.771 0.313,0.198 10 false + 1.604,1.99 1.917,2.188 0.313,0.198 10 false - 2.927,1.24 3.24,1.438 0.313,0.198 10 false *b 3.167,0.365 3.479,0.563 0.313,0.198 10 false 10.0 3.24,0.552 3.552,0.75 0.313,0.198 10 false 9.0 3.24,0.729 3.552,0.927 0.313,0.198 10 false 8.0 3.24,0.927 3.583,1.167 0.344,0.24 10 false 7.0 3.229,1.094 3.542,1.292 0.313,0.198 10 false 6.0 3.24,1.271 3.552,1.469 0.313,0.198 10 false 5.0 3.24,1.438 3.552,1.635 0.313,0.198 10 false 4.0 3.24,1.625 3.552,1.823 0.313,0.198 10 false 3.0 3.24,1.813 3.552,2.01 0.313,0.198 10 false 2.0 3.25,1.99 3.563,2.188 0.313,0.198 10 false 1.0 3.25,2.146 3.563,2.344 0.313,0.198 10 false 0.0 3.375,2.292 3.688,2.49 0.313,0.198 10 false -10 3.365,2.438 3.677,2.635 0.313,0.198 10 false (14) 4,2.292 4.313,2.49 0.313,0.198 10 false 0 3.927,2.438 4.24,2.635 0.313,0.198 10 false (32) 4.531,2.292 4.844,2.49 0.313,0.198 10 false 10 4.5,2.448 4.813,2.646 0.313,0.198 10 false (50) 5.104,2.292 5.417,2.49 0.313,0.198 10 false 20 5.083,2.438 5.396,2.635 0.313,0.198 10 false (68) 5.656,2.292 5.969,2.49 0.313,0.198 10 false 30 5.625,2.438 5.938,2.635 0.313,0.198 10 false (86) 4.271,2.552 4.583,2.75 0.313,0.198 10 false *d 4.458,0.906 4.771,1.104 0.313,0.198 10 false *c 3.198,0.146 3.51,0.344 0.313,0.198 10 false (kΩ) 6.021,2.292 7,2.479 0.979,0.188 10 false °C(°F)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (-) - 8 (+) -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


Text in Illustration
*a Sensing Portion
*b Resistance
*c Allowable Range
*d Temperature

NOTICE:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (refer to the graph).




OK

3.CHECK HARNESS AND CONNECTOR (REAR EVAPORATOR TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)

NG

REPLACE NO. 2 AIR CONDITIONING HARNESS ASSEMBLY (REAR EVAPORATOR TEMPERATURE SENSOR)

3.CHECK HARNESS AND CONNECTOR (REAR EVAPORATOR TEMPERATURE SENSOR - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the Q13 harness connector.


b.

Disconnect the G24 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-8 (+) - G24-4 (TEC) Always Below 1 Ω
Q13-7 (-) - G24-19 (SGND) Always Below 1 Ω
Q13-8 (+) - Body ground Always 10 kΩ or higher
Q13-7 (-) - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR