Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261205 COMBUSTION TYPE POWER HEATER SYSTEM J

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  Power Heater Switch Circuit  


DESCRIPTION

When the heater switch assembly (power heater switch) is turned on, the heater assembly sends a drive signal to the heater pump assembly. The heater assembly then receives the fuel necessary for combustion and starts operating.

WIRING DIAGRAM

E323850E02
2.323,1.615 2.896,1.781 0.573,0.167 10 false G177 0.313,0.865 1.531,1.167 1.219,0.302 10 false from ECU-IG NO.2 Fuse 2.333,1.781 4.135,2.24 1.802,0.458 10 false Heater Switch Assembly (Power Heater Switch) 5.344,1.323 5.917,1.49 0.573,0.167 10 false A97 5.344,1.5 6.5,1.74 1.156,0.24 10 false Heater Assembly 2.292,0.74 2.417,0.896 0.125,0.156 10 false 4 2.469,0.75 2.771,0.906 0.302,0.156 10 false IG 3.604,0.75 3.906,0.906 0.302,0.156 10 false IN 5.469,0.875 5.771,1.031 0.302,0.156 10 false IG 5.24,0.75 5.542,0.906 0.302,0.156 10 false 3 3.813,0.75 4.115,0.906 0.302,0.156 10 false 1 2.292,1.063 2.417,1.219 0.125,0.156 10 false 5 2.469,1.063 2.771,1.219 0.302,0.156 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170584E02
2.188,1.385 2.479,1.688 2.479,1.688 2.594,1.688 true 1.917,1.396 2.01,1.885 2.01,1.885 2.135,1.885 true 0.083,0.031 0.26,0.198 0.177,0.167 10 false *a 2.635,1.604 2.927,1.771 0.292,0.167 10 false E 0.458,1.073 0.865,1.25 0.406,0.177 10 false G177 2.198,1.792 2.448,1.958 0.25,0.167 10 false IG

Disconnect the heater switch assembly (power heater switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G177-4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G177-4 (IG) - Body ground Engine switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G177-5 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Heater Switch Assembly [Power Heater Switch])


OK

2.INSPECT HEATER SWITCH ASSEMBLY (POWER HEATER SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HEATER SWITCH ASSEMBLY (POWER HEATER SWITCH)
a.

Remove the heater switch assembly (power heater switch) (See page Vehicle Interior>HEATING / AIR CONDITIONING>HEATER SWITCH>REMOVAL).


E176907E05
1.396,1.219 0.99,1.625 true 2.135,1.167 2.865,1.167 true 0.625,1.167 1.156,1.167 true 0.083,0.021 0.271,0.198 0.188,0.177 10 false *a 0.51,1.094 0.635,1.271 0.125,0.177 10 false E 0.854,1.625 1.021,1.802 0.167,0.177 10 false IG 2.906,1.094 3.073,1.271 0.167,0.177 10 false IN

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (IG) - 1 (IN) Heater switch assembly (power heater switch) on Below 1 Ω
4 (IG) - 1 (IN) Heater switch assembly (power heater switch) off 10 kΩor higher



c.

Check operation indicator.

i.

Turn the heater switch assembly (power heater switch) on.


ii.

Connect a positive (+) lead from the battery to terminal 4 (IG) and a negative (-) lead to terminal 5 (E), and check that the operation indicator comes on.



Result
Result Proceed to
Indicator comes on A
Indicator does not come on B


A

3.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - HEATER ASSEMBLY)

B

REPLACE HEATER SWITCH ASSEMBLY (POWER HEATER SWITCH)

3.CHECK HARNESS AND CONNECTOR (HEATER SWITCH ASSEMBLY - HEATER ASSEMBLY)
a.

Disconnect the G177 heater switch assembly (power heater switch) connector.


b.

Disconnect the A97 heater assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G177-1 (IN) - A97-3 (IG) Always Below 1 Ω
A97-3 (IG) - Body ground Always 10 kΩor higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR