Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMBUSTION TYPE POWER HEATER SYSTEM
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261205 COMBUSTION TYPE POWER HEATER SYSTEM J

HEATING / AIR CONDITIONING  COMBUSTION TYPE POWER HEATER SYSTEM  Power Heater Alternator Circuit  


DESCRIPTION

The heater assembly receives engine operation signals from the air conditioning amplifier assembly. If this circuit is open, the heater assembly will determine that the engine operation signals indicate on. If this circuit is shorted, the heater assembly will determine that the engine operation signals indicate off and the heater assembly will not operate.

WIRING DIAGRAM

E323917E02
5.281,1.698 5.573,1.865 0.292,0.167 10 false A97 5.271,1.865 6.729,2.208 1.458,0.344 10 false Heater Assembly 1.646,1.333 1.938,1.5 0.292,0.167 10 false G25 1.646,1.5 3.24,1.823 1.594,0.323 10 false Air Conditioning Amplifier Assembly 5.24,0.792 5.365,0.948 0.125,0.156 10 false 8 5.438,0.885 5.677,1.042 0.24,0.156 10 false + 2.385,0.896 2.792,1.052 0.406,0.156 10 false HTR1 2.875,0.781 3.542,0.938 0.667,0.156 10 false 18

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEATER ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the A97 heater assembly connector.


b.

Disconnect the G25 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A97-8 (+) - G25-18 (HTR1) Always Below 1 Ω
A97-8 (+) - Body ground Always 10 kΩ or higher




OK

2.CHECK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HEATER ASSEMBLY
a.

Disconnect the G25 air conditioning amplifier assembly connector.


b.
U170635E01
0.136,0.083 0.319,0.252 0.184,0.170 10 *a 0.222,1.698 0.564,1.863 0.341,0.165 10 G25 0.136,2.071 0.568,2.242 0.432,0.171 10 HTR1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-18 (HTR1) - Body ground Engine idling, heater switch assembly (power heater switch) off Below 1 V
Engine idling, heater switch assembly (power heater switch) on 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

3.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U170634E01
1.789,0.272 2.074,0.433 0.286,0.161 10 G25 0.066,0.06 0.338,0.221 0.272,0.161 10 *a 1.427,1.321 1.224,0.597 1.224,0.597 1.112,0.597 false 0.6,0.521 0.996,0.682 0.395,0.161 10 HTR1 1.713,1.314 1.482,0.253 1.482,0.253 1.37,0.253 false 0.91,0.178 1.305,0.338 0.395,0.161 10 GND

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-18 (HTR1) - G25-14 (GND) Engine idling 11 to 14 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY