Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


U169632E02
4.052,0.167 4.323,0.375 0.271,0.208 10 false J9 2.927,0.167 3.188,0.344 0.26,0.177 10 false K4 3.229,0.167 3.5,0.354 0.271,0.188 10 false *A 4.344,0.167 4.615,0.365 0.271,0.198 10 false *B

Text in Illustration
*A for LHD *B for RHD

*1: for LHD

*2: for RHD


a.

Disconnect the K4*1 or J9*2 multiplex network master switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K4-11 (B) - K4-12 (GND) L - W-B Power supply Always 11 to 14 V
K4-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J9-11 (B) - J9-12 (GND) L - W-B Power supply Always 11 to 14 V
J9-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the K4*1 or J9*2 multiplex network master switch connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K4-15 (DOWN) - K4-12 (GND) B - W-B Power window motor down input Ignition switch ON, driver side power window regulator switch off 11 to 14 V
K4-15 (DOWN) - K4-12 (GND) B - W-B Power window motor down input Ignition switch ON, driver side power window switch down (Manual operation) Below 1 V
K4-18 (LED) - K4-12 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
K4-18 (LED) - K4-12 (GND) V - W-B LED illumination signal Ignition switch turned off Below 1 V
K4-20 (UP) - K4-12 (GND) P - W-B Power window motor up input Ignition switch ON, driver side power window switch off 11 to 14 V
K4-20 (UP) - K4-12 (GND) P - W-B Power window motor up input Ignition switch ON, driver side power window switch up (Manual operation) Below 1 V

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J9-15 (DOWN) - J9-12 (GND) B - W-B Power window motor down input Ignition switch ON, driver side power window regulator switch off 11 to 14 V
J9-15 (DOWN) - J9-12 (GND) B - W-B Power window motor down input Ignition switch ON, driver side power window switch down (Manual operation) Below 1 V
J9-18 (LED) - J9-12 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
J9-18 (LED) - J9-12 (GND) V - W-B LED illumination signal Ignition switch turned off Below 1 V
J9-20 (UP) - J9-12 (GND) P - W-B Power window motor up input Ignition switch ON, driver side power window switch off 11 to 14 V
J9-20 (UP) - J9-12 (GND) P - W-B Power window motor up input Ignition switch ON, driver side power window switch up (Manual operation) Below 1 V

If the result is not as specified, the multiplex network master switch may have a malfunction.



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


U169784E02
3.063,0.229 3.333,0.417 0.271,0.188 10 false J1 3.708,0.24 4.094,0.406 0.385,0.167 10 false K10 3.323,0.229 3.604,0.417 0.281,0.188 10 false *A 4.021,0.24 4.313,0.427 0.292,0.188 10 false *B

Text in Illustration
*A for LHD *B for RHD

*1: for LHD

*2: for RHD


a.

Disconnect the J1*1 or K10*2 power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K10-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J1*1 or K10*2 power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J1-6 (UP) - J1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
J1-6 (UP) - J1-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
J1-8 (AUTO) - J1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
J1-8 (AUTO) - J1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
J1-8 (AUTO) - J1-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
J1-4 (LED) - J1-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
J1-4 (LED) - J1-1 (GND) V - W-B LED illumination signal Ignition switch is turned off Below 1 V
J1-7 (DOWN) - J1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
J1-7 (DOWN) - J1-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K10-6 (UP) - K10-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
K10-6 (UP) - K10-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
K10-8 (AUTO) - K10-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
K10-8 (AUTO) - K10-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
K10-8 (AUTO) - K10-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
K10-4 (LED) - K10-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
K10-4 (LED) - K10-1 (GND) V - W-B LED illumination signal Ignition switch is turned off Below 1 V
K10-7 (DOWN) - K10-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
K10-7 (DOWN) - K10-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

If the result is not as specified, the power window regulator switch may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (for 5 Door)


U148042E03
3.448,0.24 3.75,0.417 0.302,0.177 10 false M2

a.

Disconnect the M2 rear power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the M2 rear power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M2-6 (UP) - M2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
M2-6 (UP) - M2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
M2-8 (AUTO) - M2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
M2-8 (AUTO) - M2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
M2-8 (AUTO) - M2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
M2-4 (LED) - M2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
M2-4 (LED) - M2-1 (GND) V - W-B LED illumination signal Ignition switch is turned off Below 1 V
M2-7 (DOWN) - M2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
M2-7 (DOWN) - M2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

If the result is not as specified, the power window regulator switch may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (for 5 Door)


U148043E03
3.479,0.24 3.771,0.406 0.292,0.167 10 false L2

a.

Disconnect the L2 rear power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the L2 rear power window regulator switch connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-6 (UP) - L2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch off 11 to 14 V
L2-6 (UP) - L2-1 (GND) L - W-B Power window motor up input Ignition switch ON, power window regulator switch up Below 1 V
L2-8 (AUTO) - L2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully open 11 to 14 V
L2-8 (AUTO) - L2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, power window auto up or down function operating Below 1 V
L2-8 (AUTO) - L2-1 (GND) P - W-B Power window motor auto up or down input Ignition switch ON, door glass fully closed 11 to 14 V
L2-4 (LED) - L2-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
L2-4 (LED) - L2-1 (GND) V - W-B LED illumination signal Ignition switch is turned off Below 1 V
L2-7 (DOWN) - L2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
L2-7 (DOWN) - L2-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V

If the result is not as specified, the rear power window regulator switch may have a malfunction.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


U148035E03
3.49,0.26 3.771,0.438 0.281,0.177 10 false K7

*1: for LHD

*2: for RHD


a.

Disconnect the K7 power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K7-2 (B) - Body ground*1 R - Body ground*1
G - Body ground*2
Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the K7 power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K7-5 (LED) - K7-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
K7-5 (LED) - K7-1 (GND) V - W-B LED illumination signal Ignition switch turned off Below 1 V
K7-7 (DOWN) - K7-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator master switch off 11 to 14 V
K7-7 (DOWN) - K7-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator master switch down Below 1 V
K7-7 (DOWN) - K7-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
K7-7 (DOWN) - K7-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
K7-7 (DOWN) - K7-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
K7-10 (UP) - K7-1 (GND) P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, power window regulator master switch off 11 to 14 V
K7-10 (UP) - K7-1 (GND) P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, power window regulator master switch up Below 1 V
K7-10 (UP) - K7-1 (GND) P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
K7-10 (UP) - K7-1 (GND) P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
K7-10 (UP) - K7-1 (GND) P - W-B*1
L - W-B*2
Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor may have a malfunction.



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


U148036E03
3.49,0.26 3.76,0.417 0.271,0.156 10 false J7

*1: for LHD

*2: for RHD


a.

Disconnect the J7 power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J7-2 (B) - Body ground G - Body ground*1
R - Body ground*2
Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the J7 power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J7-5 (LED) - J7-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
J7-5 (LED) - J7-1 (GND) V - W-B LED illumination signal Ignition switch turned off Below 1 V
J7-7 (DOWN) - J7-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch off 11 to 14 V
J7-7 (DOWN) - J7-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch down Below 1 V
J7-7 (DOWN) - J7-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
J7-7 (DOWN) - J7-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
J7-7 (DOWN) - J7-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
P - W-B*2
Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
P - W-B*2
Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
P - W-B*2
Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
P - W-B*2
Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
J7-10 (UP) - J7-1 (GND) L - W-B*1
P - W-B*2
Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the power window regulator motor may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for 5 Door)


U115619E04
3.469,0.26 3.802,0.427 0.333,0.167 10 false M4

a.

Disconnect the M4 rear power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
M4-2 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the M4 rear power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M4-5 (LED) - M4-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
M4-5 (LED) - M4-1 (GND) V - W-B LED illumination signal Ignition switch turned off Below 1 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch off 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window regulator switch down Below 1 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, door glass fully closed 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, power window auto down function operating Below 1 V
M4-7 (DOWN) - M4-1 (GND) B - W-B Power window motor down input Ignition switch ON, door glass fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
M4-10 (UP) - M4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the rear power window regulator motor may have a malfunction.



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for 5 Door)


U115620E04
3.49,0.26 3.75,0.427 0.26,0.167 10 false L4

a.

Disconnect the L4 rear window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L4-2 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the L4 rear power window regulator motor connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L4-5 (LED) - L4-1 (GND) V - W-B LED illumination signal Ignition switch ON 11 to 14 V
L4-5 (LED) - L4-1 (GND) V - W-B LED illumination signal Ignition switch turned off Below 1 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch off 11 to 14 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window regulator switch down Below 1 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully closed 11 to 14 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, power window auto down function operating Below 1 V
L4-7 (DOWN) - L4-1 (GND) B - W-B Power window motor down output Ignition switch ON, door glass fully open 11 to 14 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch off 11 to 14 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window regulator switch up Below 1 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully open 11 to 14 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, power window auto up function operating Below 1 V
L4-10 (UP) - L4-1 (GND) L - W-B Power window motor up output Ignition switch ON, door glass fully closed 11 to 14 V

If the result is not as specified, the rear power window regulator motor may have a malfunction.



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U169674E04
1.625,1.51 1.865,1.26 1.865,1.26 1.948,1.26 false 1.625,1.865 1.865,1.625 1.865,1.625 1.948,1.625 false 1.625,2.188 1.865,1.948 1.865,1.948 1.948,1.948 false 0.99,1.604 0.646,1.167 0.646,1.167 0.51,1.167 false 0.219,1.083 0.615,1.271 0.396,0.188 10 false 2I*A 0.188,1.24 0.604,1.417 0.417,0.177 10 false 2H*B 1.083,3.875 1.396,4.042 0.313,0.167 10 false G63 0.896,2.198 1.177,2.375 0.281,0.177 10 false 2F 5.854,1.531 6.156,1.708 0.302,0.177 10 false 2D 5.854,2.229 6.135,2.427 0.281,0.198 10 false 2A 1.063,2.76 1.344,2.969 0.281,0.208 10 false 2K 3.75,1.344 3.948,1.51 0.198,0.167 10 false A 1.969,1.198 2.313,1.375 0.344,0.177 10 false G65 1.969,1.552 2.313,1.708 0.344,0.156 10 false G64 1.969,1.875 2.333,2.063 0.365,0.188 10 false G63 3.573,3.885 3.938,4.052 0.365,0.167 10 false G64 0.594,5.198 0.792,5.375 0.198,0.177 10 false 2I 1.51,5.198 1.771,5.365 0.26,0.167 10 false 2H 1.875,6.417 2.167,6.604 0.292,0.188 10 false 2D 4.927,6.406 5.198,6.583 0.271,0.177 10 false 2A 3.5,7.677 3.688,7.844 0.188,0.167 10 false A 3.958,5.188 4.229,5.375 0.271,0.188 10 false 2F 5.875,5.188 6.125,5.365 0.25,0.177 10 false 2K 5.875,3.875 6.208,4.042 0.333,0.167 10 false G65 0.885,5.198 1.115,5.375 0.229,0.177 10 false *A 1.833,5.198 2.063,5.375 0.229,0.177 10 false *B

Text in Illustration
*A for LHD *B for RHD

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
G63-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU).


d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2I-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2I-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
2D-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2D-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2D-31 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2D-31 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
2H-26 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2H-26 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V

If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.