Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM D

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  INITIALIZATION  


INITIALIZE POWER WINDOW CONTROL SYSTEM (ALL DOORS)


NOTICE:
·

When a door window regulator assembly, power window regulator motor assembly, door glass or door glass run is reinstalled or replaced, the power window control system must be initialized. Functions such as the auto up and down function, jam protection function, catch protection function, remote control function, key-linked function, wireless transmitter-linked function and key-off operation function will not operate if initialization is not performed.

·

When a power window regulator motor assembly is replaced, DTC B2313 is stored. Clear the DTC after initialization (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DTC CHECK / CLEAR).

·

When performing initialization, do not perform any other procedures.

·

When performing initialization, use the power window switch of each door to initialize each door window.

·

Make sure to park the vehicle and turn off all electrical systems before performing initialization. Initialization will be canceled if the vehicle is driven during initialization.

·

Make sure not to hit, strike or vibrate the door window glass during initialization because the vehicle is learning the sliding resistance of the door window glass.

·

Make sure not to turn the ignition switch to ON or off during initialization.



HINT:
·

If the battery has been replaced, it is not necessary to initialize the power window regulator motor assembly.

·

If initialization does not complete properly, the LIN communication system may be malfunctioning (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



a.

Perform initialization according to the table below.

Condition of Power Window Proceed to
Initialization procedure for when a power window regulator motor assembly has been replaced with a new one Procedure A
·

Initialization procedure for when a power window regulator motor assembly has been removed/installed or a door glass and/or door glass run etc. have been removed/installed or replaced with new ones

·

Initialization procedure for when the window cannot fully open via a down operation (door glass remains visible)

·

Initialization procedure for when the door glass cannot fully close (erroneously operates in reverse)

·

Initialization procedure for when the door glass cannot fully open (erroneously stops)

·

Initialization procedure for when instructions to perform initialization appear in other troubleshooting flowcharts


HINT:

Use this procedure if a power window regulator motor assembly is being reused.


Procedure B


b.

Procedure A

Perform registration of the door glass position (fully closed, fully open) and sliding resistance learning.

B423049E01
3.411,4.017 4.179,4.249 0.768,0.232 10 Fully closed 3.453,3.344 4.123,3.577 0.670,0.232 10 Fully open 3.467,2.616 4.165,2.848 0.698,0.232 10 Fully open 3.649,1.775 3.959,2.008 0.310,0.232 10 Any 3.649,0.767 3.959,0.999 0.310,0.232 10 Any 5.659,0.184 6.202,0.416 0.543,0.232 10 Purpose 3.124,0.184 4.385,0.416 1.262,0.232 10 Door Glass Position 0.7,0.184 2.088,0.416 1.388,0.232 10 Operation Procedures 0.215,4.29 1.835,4.503 1.620,0.214 10 5. Initialization complete. 0.215,3.645 2.409,3.968 2.193,0.323 10 + Hold at fully closed position for 1 second or more. 0.215,3.337 2.222,3.569 2.007,0.232 10 4. Perform auto up operation.*2 0.215,2.637 2.468,3.043 2.252,0.406 10 (Switch may be operated in either manual or auto operation positions.) 0.215,2.034 2.311,2.357 2.096,0.323 10 + Hold at fully open position for 1 second or more. 0.215,1.754 2.074,1.986 1.859,0.232 10 3. Perform down operation.*1 0.215,1.348 2.459,1.580 2.243,0.232 10 (window lock switch unlocked) 0.215,0.997 2.459,1.230 2.243,0.232 10 2. Turn the ignition switch to ON. 0.215,0.675 1.518,0.907 1.303,0.232 10 1. Connect battery. 5.571,1.63 6.332,2.021 0.761,0.391 10 Initialization preparation 4.927,3.46 6.843,4.002 1.916,0.542 10 Window position initialization and sliding resistance learning (performed simultaneously)

HINT:
·

*1: Even if the door glass is in the fully open condition before performing step 3, perform the down operation for 1 second or more.

·

*2: Do not stop the procedure during step 4.




c.

Procedure B

Reset the door glass position, and perform registration of the door glass position (fully closed, fully open) and sliding resistance learning.

HINT:

When the GTS is used to perform "Reset Memory", the operation procedures are the same as procedure A.


·

When using the GTS

(a)

Using the GTS, perform "Reset Memory" under "Utility" (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>UTILITY).

(b)

Perform procedure A.


·

When not using the GTS

B369800E05
1.094,0.24 4.156,0.438 3.063,0.198 10 false Operation Procedures 4.042,0.24 6.948,0.438 2.906,0.198 10 false Door Glass Position 6.083,0.198 7.156,0.396 1.073,0.198 10 false Purpose 4.521,0.698 4.979,0.896 0.458,0.198 10 false Any 5.833,3.844 6.948,4.208 1.115,0.365 10 false Reset preparation 0.188,0.688 2.938,0.885 2.75,0.198 10 false 1 Connect auxiliary battery. 0.198,1.021 4.323,1.219 4.125,0.198 10 false 2 Turn power switch on (IG). 0.188,1.323 4.625,1.521 4.438,0.198 10 false (window lock switch unlocked) 4.406,1.708 4.865,1.906 0.458,0.198 10 false Any 4.198,2.302 6.031,2.5 1.833,0.198 10 false Fully closed 0.198,1.719 4.479,1.917 4.281,0.198 10 false 3 Perform auto up operation. 0.198,2.021 5.854,2.219 5.656,0.198 10 false 4 Confirm operation result of step 3. 0.333,2.302 7.063,2.5 6.729,0.198 10 false - If door glass reverses, proceed to step 5. 0.323,2.646 3.25,2.979 2.927,0.333 10 false - If door glass stops before reaching fully closed position, proceed to step 6. 3.688,3.375 4.438,4.219 0.75,0.844 10 false If door glass reverses from fully closed position: 4.667,3.375 5.5,4.229 0.833,0.854 10 false If door glass stops before reaching fully closed position: 0.188,3.354 7.073,3.563 6.885,0.208 10 false 5 If door glass reverses from fully closed position: 0.198,3.771 3.521,4.115 3.323,0.344 10 false (a) Within 4 seconds after door glass reverses, perform auto up operation and fully close door glass. 0.198,4.552 3.583,4.906 3.385,0.354 10 false + Hold at fully closed position for 6 seconds or more. 0.156,4.927 3.146,5.271 2.99,0.344 10 false (Switch may be operated in either manual or auto operation positions.) 0.146,5.646 3.083,5.969 2.938,0.323 10 false 6 If door glass stops before reaching fully closed position: 3.75,5.99 4.5,6.719 0.75,0.729 10 false Reverses at fully closed position 4.708,6.021 5.521,6.729 0.813,0.708 10 false Stops before reaching fully closed position 4,5.354 4.458,5.552 0.458,0.198 10 false Any 5.052,5.354 5.51,5.552 0.458,0.198 10 false Any 0.26,6.458 3.438,6.813 3.177,0.354 10 false (a) Perform auto up operation until door glass moves upward. 0.25,7.083 3.333,7.438 3.083,0.354 10 false (b) Perform auto up operation again and move door glass to fully closed position. 0.156,7.719 3.229,8.156 3.073,0.438 10 false (Switch may be operated in either manual or auto operation positions.)

B369801E03
0.188,0.5 4.01,0.698 3.823,0.198 10 false 7 Perform down operation. 0.167,0.906 3.375,1.219 3.208,0.313 10 false + Hold at door glass stopped position*1 for 1 second or more. 0.167,1.594 3.156,1.99 2.99,0.396 10 false (Switch may be operated in either manual or auto operation positions.) 4.24,0.74 6.073,0.938 1.833,0.198 10 false Fully closed 3.75,1.396 7.156,1.792 3.406,0.396 10 false Door glass stopped position 5.917,1.594 6.781,2.031 0.865,0.438 10 false Reset window position 0.167,2.469 5.063,2.667 4.896,0.198 10 false 8 Perform auto down operation.*2 0.156,2.833 3.292,3.188 3.135,0.354 10 false + Hold at door glass stopped position for 4 seconds or more. 3.76,2.542 7.156,2.938 3.396,0.396 10 false Door glass stopped position 4.292,3.208 5.823,3.406 1.531,0.198 10 false Fully open 0.188,3.708 4.469,3.906 4.281,0.198 10 false 9 Perform auto up operation. 0.198,4.094 3.396,4.292 3.198,0.198 10 false + Hold at fully closed position for 1 second or more. 0.188,4.552 4.469,4.75 4.281,0.198 10 false 10 Initialization complete*3 4.292,3.719 5.823,3.917 1.531,0.198 10 false Fully open 4.281,4.354 6.115,4.552 1.833,0.198 10 false Fully closed 4.271,5.063 6.104,5.26 1.833,0.198 10 false Fully closed 5.813,4.302 6.917,4.646 1.104,0.344 10 false Sliding resistance learning

HINT:
·

*1: If catch protection function operates during step 7, then hold the switch in the auto down position within 4 seconds.

·

*2: The door glass stopped position is the fully open position stored in the ECU.

·

*3: After performing step 7, return the switch to the neutral position once, and then perform an auto down operation.

·

*4: After completion, check that the door glass can fully close via an auto up operation.

·

If the initialization is not completed properly, the LIN communication system may have a malfunction (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).