CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-30 (BECU) - Body ground | - | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| A-31 (ALTB) - Body ground | - | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| A-32 (IG) - Body ground | - | Ignition switch power supply | Ignition switch ON | 11 to 14 V |
| A-32 (IG) - Body ground | - | Ignition switch power supply | Ignition switch off | Below 1 V |
| A-29 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC | 11 to 14 V |
| A-29 (ACC) - Body ground | - | ACC power supply | Ignition switch off | Below 1 V |
| A-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| G63-3 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the main body ECU (multiplex network body ECU).
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G63-17 (GOSW) - Body ground | LG - Body ground | Glass hatch opener switch input | Glass hatch open | Below 1 V |
| G63-17 (GOSW) - Body ground | LG - Body ground | Glass hatch opener switch input | Ignition switch off, all doors closed and glass hatch closed | Pulse generation (See waveform 1 or 2) |
| 2I-9 (GHRY) - Body ground*1 | B - Body ground | Glass hatch opener relay output | Ignition switch ON, glass hatch opener switch off | Below 1 V |
| 2I-9 (GHRY) - Body ground*1 | B - Body ground | Glass hatch opener relay output | Ignition switch ON, glass hatch opener switch on | 11 to 14 V |
| 2H-9 (GHRY) - Body ground*2 | B - Body ground | Glass hatch opener relay output | Ignition switch ON, glass hatch opener switch off | Below 1 V |
| 2H-9 (GHRY) - Body ground*2 | B - Body ground | Glass hatch opener relay output | Ignition switch ON, glass hatch opener switch on | 11 to 14 V |
*1: for LHD
*2: for RHD
If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.
Using an oscilloscope, check waveform 1.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G63-17 (GOSW) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Glass hatch closed |
Using an oscilloscope, check waveform 2.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G63-17 (GOSW) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and glass hatch closed |