Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2015.06–2016.08
RM27T0E _59 Vehicle Exterior _053743 SLIDING ROOF / CONVERTIBLE _0261242 SLIDING ROOF SYSTEM U

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  TERMINALS OF ECU  


CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)


U115528E04
3.458,0.24 3.719,0.396 0.26,0.156 10 false W2

a.

Disconnect the W2 ECU connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W2-1 (B) - W2-2 (E) W - W-B Battery power supply Always 11 to 14 V
W2-5 (IG) - W2-2 (E) L - W-B IG power supply Ignition switch off Below 1 V
W2-5 (IG) - W2-2 (E) L - W-B IG power supply Ignition switch ON 11 to 14 V
W2-2 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the W2 ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W2-7 (OPN) - W2-2 (E) LG - W-B Sliding roof motor open Ignition switch ON, sliding roof closed
Slide open switch off
11 to 14 V
W2-7 (OPN) - W2-2 (E) LG - W-B Sliding roof motor open Ignition switch ON, sliding roof closed
Slide open switch on
Below 1 V
W2-9 (CLS) - W2-2 (E) B - W-B Sliding roof motor close Ignition switch ON, sliding roof open
Slide close switch off
11 to 14 V
W2-9 (CLS) - W2-2 (E) B - W-B Sliding roof motor close Ignition switch ON, sliding roof open
Slide close switch on
Below 1 V
W2-10 (UP) - W2-2 (E) R - W-B Sliding roof motor up Ignition switch ON, sliding roof tilted downward
Tilt up switch off
11 to 14 V
W2-10 (UP) - W2-2 (E) R - W-B Sliding roof motor up Ignition switch ON, sliding roof tilted downward
Tilt up switch on
Below 1 V
W2-8 (DWN) - W2-2 (E) P - W-B Sliding roof motor down Ignition switch ON, sliding roof tilted upward
Tilt down switch off
11 to 14 V
W2-8 (DWN) - W2-2 (E) P - W-B Sliding roof motor down Ignition switch ON, sliding roof tilted upward
Tilt down switch on
Below 1 V

If the result is not as specified, the sliding roof drive gear sub-assembly may have a malfunction.




CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U169674E06
1.625,1.469 1.865,1.219 1.865,1.219 1.948,1.219 false 1.625,1.823 1.865,1.583 1.865,1.583 1.948,1.583 false 1.625,2.135 1.865,1.896 1.865,1.896 1.948,1.896 false 1,1.542 0.656,1.104 0.656,1.104 0.521,1.104 false 0.25,1.031 0.552,1.188 0.302,0.156 10 false 2I*A 0.198,1.188 0.552,1.344 0.354,0.156 10 false 2H*B 1.083,3.865 1.365,4.021 0.281,0.156 10 false G63 0.896,2.167 1.104,2.323 0.208,0.156 10 false 2F 5.865,1.49 6.073,1.646 0.208,0.156 10 false 2D 5.865,2.188 6.073,2.344 0.208,0.156 10 false 2A 1.073,2.74 1.281,2.896 0.208,0.156 10 false 2K 3.75,1.323 3.865,1.469 0.115,0.146 10 false A 1.958,1.156 2.292,1.302 0.333,0.146 10 false G65 1.958,1.51 2.271,1.656 0.313,0.146 10 false G64 1.958,1.833 2.271,1.979 0.313,0.146 10 false G63 3.583,3.865 3.875,4.021 0.292,0.156 10 false G64 0.594,5.198 0.75,5.354 0.156,0.156 10 false 2I 1.5,5.198 1.708,5.354 0.208,0.156 10 false 2H 1.875,6.406 2.094,6.563 0.219,0.156 10 false 2D 4.927,6.406 5.146,6.563 0.219,0.156 10 false 2A 3.5,7.667 3.635,7.823 0.135,0.156 10 false A 3.948,5.188 4.146,5.344 0.198,0.156 10 false 2F 5.885,5.177 6.083,5.333 0.198,0.156 10 false 2K 5.896,3.865 6.198,4.021 0.302,0.156 10 false G65 0.875,5.177 1.104,5.354 0.229,0.177 10 false *A 1.854,5.177 2.083,5.354 0.229,0.177 10 false *B

Text in Illustration
*A for LHD *B for RHD

a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
G63-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU).


d.

Measure the voltage according to the value(s) in the table below.

for LHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2I-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2I-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
G64-11 (L2) - Body ground GR - Body ground Driver side door key-linked lock input Driver side door key cylinder in lock position Below 1 V
G64-11 (L2) - Body ground GR - Body ground Driver side door key-linked lock input Ignition switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
G64-24 (UL3) - Body ground LG - Body ground Driver side door key-linked unlock input Driver side door key cylinder in unlock position Below 1 V
G64-24 (UL3) - Body ground LG - Body ground Driver side door key-linked unlock input Ignition switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 3 or 4)
G64-26 (RDA) - Body ground* P - Body ground Door control receiver input No key in ignition key cylinder, all doors closed and transmitter switch off → on Pulse generation

for RHD:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2H-26 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2H-26 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V
G64-11 (L2) - Body ground GR - Body ground Driver side door key-linked lock input Driver side door key cylinder in lock position Below 1 V
G64-11 (L2) - Body ground GR - Body ground Driver side door key-linked lock input Ignition switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
G64-24 (UL3) - Body ground LG - Body ground Driver side door key-linked unlock input Driver side door key cylinder in unlock position Below 1 V
G64-24 (UL3) - Body ground LG - Body ground Driver side door key-linked unlock input Ignition switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 3 or 4)
G64-26 (RDA) - Body ground* P - Body ground Door control receiver input No key in ignition key cylinder, all doors closed and transmitter switch off → on Pulse generation

*: w/o Entry and Start System


If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.


e.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) G64-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door key cylinder in neutral position


f.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) G64-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door key cylinder in neutral position


g.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) G64-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder in neutral position


h.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) G64-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder in neutral position



CHECK CERTIFICATION ECU (w/ Smart Key System)


U147948E03
4.604,0.625 4.948,0.802 0.344,0.177 10 false G39 2.385,0.625 2.719,0.802 0.333,0.177 10 false G38

a.

Disconnect the G38 ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G38-1 (+B) - G38-15 (E) V - W-B Battery power supply Always 11 to 14 V
G38-15 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
G38-16 (IG) - G38-15 (E) W - W-B IG power supply Ignition switch off Below 1 V
G38-16 (IG) - G38-15 (E) W - W-B IG power supply Ignition switch ON 11 to 14 V
G38-17 (CUTB) - G38-15 (E) L - W-B Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.



c.

Reconnect the G38 ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G39-5 (RCO) - G38-15 (E) L - W-B Door control receiver power source Ignition switch off, all doors closed and transmitter switch not pressed Below 1 V
G39-5 (RCO) - G38-15 (E) L - W-B Door control receiver power source Ignition switch off, all doors closed and transmitter switch pressed 4.5 to 5.5 V
G39-15 (RDA) - G38-15 (E) G - W-B Door control receiver data input signal Ignition switch off 11 to 14 V pulse generation at regular intervals
G39-16 (RSSI) - G38-15 (E) P - W-B Door control receiver electric wave existence signal All doors locked, all doors closed and transmitter switch not pressed 11 to 14 V
G39-16 (RSSI) - G38-15 (E) P - W-B Door control receiver electric wave existence signal All doors locked, all doors closed and transmitter switch pressed Below 2 V

If the result is not as specified, the certification ECU may have a malfunction.