Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261249 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·
B216808E07
0.417,1.823 1.333,2 0.917,0.177 10 false Centering Bolt 2.167,1.823 3.083,2 0.917,0.177 10 false Standard Bolt

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT BACK DOOR

a.

w/ Back Door Tire Carrier:

i.

Check that the clearance measurements of areas A through I are within the standard range.

B241628E02
1.167,0.417 1.344,0.667 0.177,0.25 10 false A 5.302,0.833 5.583,1.083 0.281,0.25 10 false B 6,3 6.281,3.25 0.281,0.25 10 false E 4.885,2.75 5.167,3 0.281,0.25 10 false F 2.75,2 3.031,2.25 0.281,0.25 10 false H 6.083,1.083 6.365,1.333 0.281,0.25 10 false C 6.5,1.917 6.781,2.167 0.281,0.25 10 false D 3.25,3 3.531,3.25 0.281,0.25 10 false I 3.083,1.083 3.365,1.333 0.281,0.25 10 false G

Standard:
Area Measurement Area Measurement
A 8.35 to 11.35 mm (0.329 to 0.447 in.) B 4.65 to 7.65 mm (0.183 to 0.301 in.)
C 5.05 to 8.05 mm (0.199 to 0.317 in.) D 5.25 to 8.25 mm (0.207 to 0.325 in.)
E 5.25 to 8.25 mm (0.207 to 0.325 in.) F 8.85 to 11.85 mm (0.348 to 0.467 in.)
G 4.85 to 7.85 mm (0.191 to 0.309 in.) H 5.25 to 8.25 mm (0.207 to 0.325 in.)
I 5.25 to 8.25 mm (0.207 to 0.325 in.) - -




b.

w/o Back Door Tire Carrier:

i.

Check that the clearance measurements of areas A through I are within the standard range.

B241629E02
1.25,0.583 1.5,0.823 0.25,0.24 10 false A 5.188,0.844 5.5,1.083 0.313,0.24 10 false B 6.104,1.083 6.417,1.323 0.313,0.24 10 false C 6.5,1.927 6.688,2.167 0.188,0.24 10 false D 6.021,3.01 6.333,3.25 0.313,0.24 10 false E 4.51,2.677 4.667,2.917 0.156,0.24 10 false F 3.135,1.083 3.333,1.323 0.198,0.24 10 false G 2.75,1.927 3.063,2.167 0.313,0.24 10 false H 3.25,3.01 3.396,3.25 0.146,0.24 10 false I

Standard:
Area Measurement Area Measurement
A 8.35 to 11.35 mm (0.329 to 0.447 in.) B 5.05 to 8.05 mm (0.199 to 0.317 in.)
C 4.65 to 7.65 mm (0.183 to 0.301 in.) D 4.95 to 7.95 mm (0.195 to 0.313 in.)
E 4.95 to 7.95 mm (0.195 to 0.313 in.) F 8.85 to 11.85 mm (0.348 to 0.467 in.)
G 4.65 to 7.65 mm (0.183 to 0.301 in.) H 4.95 to 7.95 mm (0.195 to 0.313 in.)
I 5.05 to 8.05 mm (0.199 to 0.317 in.) - -




Hide 2.ADJUST BACK DOOR

a.

w/ Back Door Tire Carrier:

i.

Remove the spare wheel cover pad (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).


ii.

Remove the spare wheel cover (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).


iii.

Remove the spare tire.



b.
B237277E01
0.043,0 0.263,0.205 0.219,0.205 10 *A 0.043,2.251 0.263,2.456 0.219,0.205 10 *B

Loosen the hinge bolts on the body and adjust the position of the door.

Text in Illustration
*A w/ Back Door Tire Carrier
*B w/o Back Door Tire Carrier


c.

Tighten the hinge bolts on the body.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


d.
B237278E03
0.083,0.083 0.5,0.417 0.417,0.333 10 true *A 0.083,2.271 0.5,2.583 0.417,0.313 10 true *B

Loosen the hinge bolts on the door and adjust the position of the door.

Text in Illustration
*A w/ Back Door Tire Carrier
*B w/o Back Door Tire Carrier


e.

Tighten the hinge bolts on the door.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


f.
B243388

Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and then hitting the striker with a plastic-faced hammer.


g.

Using a T40 "TORX" socket, tighten the striker mounting screws.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


h.
B133659

Using a T30 "TORX" socket, adjust the back door side male stopper position by slightly loosening the stopper mounting screws and then hitting the stopper with a plastic-faced hammer.


i.

Using a T30 "TORX" socket, tighten the male stopper mounting screws.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


j.
B129932

Loosen the back door side female stopper bolts and adjust the stopper position.


k.

Tighten the female stopper bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


l.

w/ Back Door Tire Carrier:

i.

Install the spare tire.


ii.

Install the spare wheel cover (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>REASSEMBLY).


iii.

Install the spare wheel cover pad (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>REASSEMBLY).