Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261257 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Fluid Level Warning Switch Circuit  


DESCRIPTION

When the volume of washer fluid decreases to below a certain level (when the level warning switch assembly is turned on), the multi-information display warns the driver by displaying a message*1 or the combination meter assembly warns the driver by displaying a washer fluid warning light*2.

*1: w/ Multi-information Display

*2: w/o Multi-information Display


WIRING DIAGRAM

E282042E04
0.583,2.344 1.979,2.823 1.396,0.479 10 false Level Warning Switch Assembly 2.219,2.313 3.615,2.792 1.396,0.479 10 false Washer Wiring Assembly 5.146,2.229 5.458,2.427 0.313,0.198 10 false G7 5.146,2.406 6.354,2.885 1.208,0.479 10 false Combination Meter Assembly 5.396,1.198 6.01,1.396 0.615,0.198 10 false WLVL 1.885,0.979 2.042,1.177 0.156,0.198 10 false 1 1.896,1.594 2.052,1.792 0.156,0.198 10 false 2 3.323,0.99 3.479,1.188 0.156,0.198 10 false 3 3.323,1.594 3.479,1.792 0.156,0.198 10 false 6 1.885,1.208 2.042,1.406 0.156,0.198 10 false B 1.896,1.813 2.052,2.01 0.156,0.198 10 false B 3,1.292 3.156,1.49 0.156,0.198 10 false S 3,1.896 3.156,2.094 0.156,0.198 10 false E 3.271,1.219 3.729,1.417 0.458,0.198 10 false A23 3.281,1.823 3.74,2.021 0.458,0.198 10 false A23 5.146,1.094 5.458,1.292 0.313,0.198 10 false 20

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (WASHER SWITCH)
a.

Use the Data List to check if the level warning switch assembly is functioning properly (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Washer Switch Level warning switch / ON or OFF ON: Fluid volume is less than 550 to 750 cc (33.5 to 45.7 cu.in.)
OFF: Fluid volume is more than 550 to 750 cc (33.5 to 45.7 cu.in.)
-

OK:

On intelligent tester screen, item changes between ON and OFF according to above chart.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT LEVEL WARNING SWITCH ASSEMBLY
2.INSPECT LEVEL WARNING SWITCH ASSEMBLY
a.

Remove the level warning switch assembly (See page Vehicle Exterior>WIPER / WASHER>WASHER LEVEL WARNING SWITCH>REMOVAL).


b.

Inspect the level warning switch assembly (See page Vehicle Exterior>WIPER / WASHER>WASHER LEVEL WARNING SWITCH>INSPECTION)



OK

3.INSPECT WASHER WIRING ASSEMBLY

NG

REPLACE LEVEL WARNING SWITCH ASSEMBLY

3.INSPECT WASHER WIRING ASSEMBLY
a.
U149398E03
2.031,1.25 2.354,0.938 2.354,0.938 2.563,0.938 false 2.031,1.594 2.354,1.896 2.354,1.896 2.563,1.896 false 2.594,0.854 2.854,1.125 0.26,0.271 10 false S 1.583,0.635 2.115,0.875 0.531,0.24 10 false A23 2.594,1.813 2.917,2.083 0.323,0.271 10 false E 1.667,2.802 2.146,3.094 0.479,0.292 10 false B

Disconnect the A23 and B washer wiring assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-3 (S) - B-1 Always Below 1 Ω
A23-6 (E) - B-2 Always Below 1 Ω
A23-3 (S) or B-1 - Body ground Always 10 kΩ or higher
A23-6 (E) or B-2 - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (WASHER WIRING ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE WASHER WIRING ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (WASHER WIRING ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the A23 washer wiring assembly connector.


b.

Disconnect the G7 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A23-3 (S) - G7-20 (WLVL) Always Below 1 Ω
A23-6 (E) - Body ground Always Below 1 Ω
A23-3 (S) or G7-20 (WLVL) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR