Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261258 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 82375B 1.INSTALL WIPER MOTOR WIRE

a.

Attach the claw to install the wiper motor wire.


Hide 85110 2.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the connector.


c.

w/o Spring:

i.
E197630E01
1.041,1.49 1.245,1.692 0.204,0.202 10 *1 1.101,0.92 1.101,1.469 false

Apply MP grease to the crank arm pivot of the front wiper crank.

Text in Illustration
*1 Crank Arm Pivot
V100155

MP grease


ii.
E197632

Connect the rod to the crank arm pivot of the front wiper crank.



Hide 85012A 3.INSTALL FRONT WIPER CRANK SUB-ASSEMBLY (for RHD, w/ Spring)

a.

Check the automatic stop position.

i.

Check that the motor stops automatically at the automatic stop position (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION).



b.
E197629E01
0.062,0 0.341,0.267 0.279,0.267 10 *A 2.395,1.754 2.597,1.980 0.202,0.225 10 *b 0.384,0.974 0.586,1.199 0.202,0.225 10 *a 2.489,1.495 2.489,1.754 false 0.572,1.075 0.725,1.075 0.725,1.075 0.951,1.427 false

Install the front wiper crank sub-assembly to the front wiper motor assembly with the nut so that center lines of the crank arm spring and wiper link stay are parallel.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)

Text in Illustration
*A Front Wiper Crank Set Position
*a Center Line of Crank Arm Spring
*b Center Line of Wiper Link Stay

HINT:

Hold the front wiper crank sub-assembly by hand when tightening the nut.



c.
E201905E02
2.667,0.802 2.479,0.802 false 2.719,0.719 2.979,0.948 0.26,0.229 10 false *1

Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.

Text in Illustration
*1 Crank Arm Pivot
V100155

MP grease


d.

Connect the rod of the windshield wiper link to the front wiper crank.


Hide 4.INSTALL WINDSHIELD WIPER MOTOR AND LINK

a.
E197634E01
0.518,0.349 0.719,0.527 0.201,0.177 10 *1 1.93,0.349 2.131,0.527 0.201,0.177 10 *1 0.504,0.457 0.463,0.457 0.463,0.457 0.412,0.874 false 2.105,0.437 2.158,0.437 2.158,0.437 2.454,0.896 false

Attach the grommet as shown in the illustration.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

Text in Illustration
*1 Grommet

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.



b.

Install the windshield wiper motor and link with the 2 bolts.


c.

Connect the connector.


d.

Attach the clamp.


Hide 55781E 5.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
E197614E04
2.156,0.208 2.427,0.396 0.271,0.188 10 false *2 1.031,1.521 1.302,1.729 0.271,0.208 10 false *1

Attach the 10 guides (B).


b.

Attach the 6 claws and guide (A) as shown in the illustration.

Text in Illustration
*1 Guide A
*2 Guide B


c.

Install the 2 clips to the cowl top ventilator louver sub-assembly.


Hide 55784B 6.INSTALL CENTER NO. 2 COWL TOP VENTILATOR LOUVER

a.

Attach the 2 claws and 3 guides to install the center No. 2 cowl top ventilator louver.


Hide 53383 7.INSTALL HOOD TO COWL TOP SEAL

Hide 8.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

Operate the wiper and stop the windshield wiper motor at the automatic stop position.


b.
E112237E08
0.307,0.717 0.483,0.899 0.176,0.182 10 *1 0.43,2.768 0.617,2.922 0.187,0.154 10 *2 2.606,3.798 2.785,3.952 0.180,0.154 10 *3 0.504,0.818 0.801,0.818 0.801,0.818 1.334,1.43 false 0.675,2.869 0.912,2.869 0.912,2.869 1.185,3.265 false 2.661,3.743 2.661,3.562 2.661,3.562 1.939,3.511 false

When reusing the front wiper arm and blade assembly RH:

i.

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serration
*2 Wire Brush
*3 Wiper Pivot Serration



c.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



d.
E197636E02
2.229,1.031 2.49,0.74 2.49,0.74 2.583,0.74 false 1.448,3.417 1.271,3.125 1.271,3.125 1.177,3.125 false 1.698,0.563 2.125,0.563 2.125,0.563 2.198,0.688 false 1.76,1.479 2.063,1.479 2.063,1.479 2.156,1.385 true 1.865,3.01 1.573,3.01 1.573,3.01 1.5,3.104 false 1.865,3.865 1.615,3.865 1.615,3.865 1.49,3.698 false 2.021,0.75 2.146,0.938 0.125,0.188 10 false a 2.021,1.104 2.146,1.292 0.125,0.188 10 false b 1.521,0.49 1.708,0.677 0.188,0.188 10 false *a 1.563,1.365 1.75,1.552 0.188,0.188 10 false *b 2.604,0.656 2.792,0.844 0.188,0.188 10 false *1 0.99,3.042 1.177,3.229 0.188,0.188 10 false *1 1.542,3.073 1.667,3.26 0.125,0.188 10 false c 1.542,3.427 1.667,3.615 0.125,0.188 10 false d 0.083,0.063 0.271,0.25 0.188,0.188 10 false *A 0.083,2.354 0.271,2.542 0.188,0.188 10 false *B 1.885,2.927 2.073,3.115 0.188,0.188 10 false *a 1.885,3.771 2.073,3.958 0.188,0.188 10 false *b

Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Standard
Area Standard Condition
a 7.5 mm (0.295 in.)
b 7.5 mm (0.295 in.)
c 7.5 mm (0.295 in.)
d 7.5 mm (0.295 in.)

Text in Illustration
*A for LHD
*B for RHD
*1 Ceramic Dot
*a Upper Limit
*b Lower Limit

HINT:
·

Hold the wiper arm by hand while tightening the nut.

·

Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.




Hide 9.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.
E112237E08
0.307,0.717 0.483,0.899 0.176,0.182 10 *1 0.43,2.768 0.617,2.922 0.187,0.154 10 *2 2.606,3.798 2.785,3.952 0.180,0.154 10 *3 0.504,0.818 0.801,0.818 0.801,0.818 1.334,1.43 false 0.675,2.869 0.912,2.869 0.912,2.869 1.185,3.265 false 2.661,3.743 2.661,3.562 2.661,3.562 1.939,3.511 false

When reusing the front wiper arm and blade assembly LH:

i.

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serration
*2 Wire Brush
*3 Wiper Pivot Serration



b.

When reusing the windshield wiper link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



c.
E197693E02
1.969,0.875 2.094,0.875 2.094,0.875 2.313,1.156 false 0.865,2.938 0.99,2.938 0.99,2.938 1.229,3.229 false 1.698,2.792 1.438,2.792 1.438,2.792 1.333,2.875 false 1.76,3.646 1.5,3.646 1.5,3.646 1.396,3.563 false 2.635,0.771 2.438,0.771 2.438,0.771 2.354,0.854 false 2.635,1.51 2.438,1.51 2.438,1.51 2.354,1.438 false 2.406,1.229 2.563,1.448 0.156,0.219 10 false b 2.406,0.906 2.563,1.125 0.156,0.219 10 false a 1.385,3.302 1.542,3.521 0.156,0.219 10 false d 1.385,2.938 1.542,3.156 0.156,0.219 10 false c 1.719,2.719 1.875,2.938 0.156,0.219 10 false *a 1.802,3.563 1.958,3.781 0.156,0.219 10 false *b 1.802,0.792 2.042,1.01 0.24,0.219 10 false *1 0.083,0 0.323,0.219 0.24,0.219 10 false *A 0.083,2.177 0.323,2.396 0.24,0.219 10 false *B 0.688,2.844 0.927,3.063 0.24,0.219 10 false *1 2.667,0.677 2.823,0.896 0.156,0.219 10 false *a 2.646,1.417 2.802,1.635 0.156,0.219 10 false *b

Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Standard
Area Standard Condition
a 7.5 mm (0.295 in.)
b 7.5 mm (0.295 in.)
c 7.5 mm (0.295 in.)
d 7.5 mm (0.295 in.)

Text in Illustration
*A for LHD
*B for RHD
*1 Ceramic Dot
*a Upper Limit
*b Lower Limit

HINT:
·

Hold the wiper arm by hand while tightening the nut.

·

Raise and lower the wiper arm a few times to confirm that it has settled to the specified position.




d.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.


Hide 85192 10.INSTALL WINDSHIELD WIPER ARM COVER

a.
E201164

Attach the 3 claws to install the wiper arm cover.

HINT:

Use the same procedure described for the LH side.



Hide 53867H 11.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.

Attach the 5 claws to install the front fender to cowl side seal LH.


Hide 53866J 12.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 53828J 13.INSTALL FRONT FENDER SIDE PANEL PROTECTOR LH

a.

Attach the 4 clips and 2 guides to install the fender side panel.


Hide 53827K 14.INSTALL FRONT FENDER SIDE PANEL PROTECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).