Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261258 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.
E197600E01
3.169,0.596 3.313,0.784 0.144,0.189 10 A 2.849,1.648 2.993,1.837 0.144,0.189 10 B 0.388,2.697 0.532,2.886 0.144,0.189 10 C 0.517,1.025 0.692,1.200 0.175,0.175 10 *1 2.82,2.239 2.995,2.413 0.175,0.175 10 *1 2.989,2.321 3.103,2.321 3.103,2.321 3.276,2.195 false 0.5,1.12 0.353,1.12 false

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

Standard:
Area Standard Condition
A 47.5 mm (1.87 in.)
B 30.4 mm (1.20 in.)
C 9.5 mm (0.374 in.)

Text in Illustration
*1 Moulding Edge



b.
E201882E01
0.04,0.024 0.307,0.270 0.267,0.246 10 *A 0.04,2.439 0.307,2.685 0.267,0.246 10 *B 0.118,1.826 0.249,2.004 0.131,0.178 10 a 1.006,4.393 1.137,4.572 0.131,0.178 10 b 0.483,1.937 0.741,2.138 0.258,0.201 10 *1 1.42,4.455 1.678,4.617 0.258,0.163 10 *2 1.535,4.442 1.535,4.241 false 0.595,1.937 0.595,1.768 0.595,1.768 0.244,1.673 false

Stop the front wiper motor and link assembly operation.

Text in Illustration
*A for RH Side
*B for LH Side
*1 Cowl Side Seal Edge
*2 Louver Edge


c.

Check the automatic stop position.

OK:

The front wipers stop at the positions shown in the illustration.


Standard:
Area Standard Condition
a 35.6 to 55.6 mm (1.40 to 2.19 in.)
b 18.9 to 38.9 mm (0.744 to 1.53 in.)


If the result is not as specified, remove and reinstall the wiper arm and blade assembly, and then perform the on-vehicle inspection described above to inspect the wiper motor and link assembly again. If the result is not as specified again, inspect the wiper motor and link assembly with it removed from the vehicle body (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION).


Hide 85110 2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.
E197601E01
0.037,2.273 0.469,2.675 0.433,0.401 0.132,0.56 0.336,0.769 0.205,0.209 10 A 0.548,1.564 0.752,1.746 0.205,0.182 10 B 2.667,2.552 2.853,2.789 0.186,0.237 10 C 0.141,2.312 0.345,2.622 0.205,0.310 10 *1 2.71,0.962 2.915,1.175 0.205,0.214 10 *1 0.227,2.317 0.227,2.217 0.227,2.217 0.143,2.181 false 2.884,1.051 3.102,1.051 false

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

Standard:
Area Standard Condition
A 47.5 mm (1.87 in.)
B 30.4 mm (1.20 in.)
C 13.0 mm (0.512 in.)

Text in Illustration
*1 Moulding Edge



b.
E201883E01
2.721,1.995 3.030,2.276 0.308,0.281 10 *1 1.811,4.474 1.986,4.624 0.175,0.150 10 *2 0.046,0.022 0.354,0.303 0.308,0.281 10 *A 0.049,2.313 0.357,2.594 0.308,0.281 10 *B 3.201,1.895 3.355,2.176 0.154,0.281 10 a 2.286,4.399 2.426,4.577 0.140,0.178 10 b 2.819,1.975 2.819,1.629 2.819,1.629 3.191,1.675 false 1.911,4.252 1.911,4.474 false

Stop the front wiper motor and link assembly operation.

Text in Illustration
*A for LH Side
*B for RH Side
*1 Cowl Side Seal Edge
*2 Louver Edge


c.

Check the automatic stop position.

OK:

The front wipers stop at the positions shown in the illustration.


Standard:
Area Standard Condition
a 35.6 to 55.6 mm (1.40 to 2.19 in.)
b 18.9 to 38.9 mm (0.744 to 1.53 in.)


If the result is not as specified, remove and reinstall the wiper arm and blade assembly, and then perform the on-vehicle inspection described above to inspect the wiper motor and link assembly again. If the result is not as specified again, inspect the wiper motor and link assembly with it removed from the vehicle body (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION).