Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261275 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal and outputs it to the main body ECU. The main body ECU turns the headlights and taillights on or off according to the signal.

DTC Code DTC Detection Condition Trouble Area
B1244
·

Malfunction in the automatic light control sensor.

·

Open or short in the automatic light control sensor circuit.


·

Automatic light control sensor

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

E188439E04
0.236,2.731 0.565,2.904 0.329,0.173 10 H19 0.236,2.875 2.253,3.086 2.017,0.211 10 Automatic Light Control Sensor 5.339,2.711 5.668,2.884 0.329,0.173 10 G64 5.339,2.855 7.023,3.222 1.684,0.367 10 Main Body ECU (Multiplex Network Body ECU) 1.104,0.602 1.510,0.804 0.406,0.202 10 CLTB 1.104,1.387 1.510,1.589 0.406,0.202 10 CLTS 1.104,2.19 1.510,2.392 0.406,0.202 10 CLTE 5.727,0.602 6.133,0.804 0.406,0.202 10 CLTB 5.727,1.387 6.133,1.589 0.406,0.202 10 CLTS 5.727,2.19 6.133,2.392 0.406,0.202 10 CLTE 5.376,0.502 5.563,0.668 0.187,0.166 10 20 5.376,1.3 5.563,1.466 0.187,0.166 10 21 5.376,2.099 5.563,2.266 0.187,0.166 10 22 1.63,0.502 1.817,0.668 0.187,0.166 10 6 1.63,1.3 1.817,1.466 0.187,0.166 10 5 1.63,2.099 1.817,2.266 0.187,0.166 10 3

PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1244 output does not occur.




OK

NG

2.READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate Illumination rate information / 0 ms. to 99.99 ms. Value output according to ambient light levels -

OK:

Normal condition listed above is displayed.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the G64 main body ECU connector.


b.

Disconnect the H19 automatic light control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G64-22 (CLTE) - H19-3 (CLTE) Always Below 1 Ω
G64-21 (CLTS) - H19-5 (CLTS) Always Below 1 Ω
G64-20 (CLTB) - H19-6 (CLTB) Always Below 1 Ω
G64-22 (CLTE) - Body ground Always 10 kΩ or higher
G64-21 (CLTS) - Body ground Always 10 kΩ or higher
G64-20 (CLTB) - Body ground Always 10 kΩ or higher




OK

4.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
U170660E01
0.097,0.012 0.288,0.196 0.191,0.184 10 *a 0.991,1.891 1.369,2.066 0.378,0.174 10 CLTE 2.054,1.105 1.277,1.863 false 2.138,1.838 2.516,2.013 0.378,0.174 10 CLTB 2.329,1.11 2.329,1.798 false 0.233,0.499 0.555,0.662 0.323,0.163 10 G64

Reconnect the G64 main body ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G64-20 (CLTB) - G64-22 (CLTE) Ignition switch off Below 1 V
Ignition switch ON and headlight dimmer switch in AUTO position 11 to 14 V


Text in Illustration
*a Component with harness connected
(Main Body ECU)



OK

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR
a.
U170661E01
0.054,0.027 0.257,0.183 0.202,0.156 10 *a 2.561,1.784 2.951,1.928 0.390,0.144 10 CLTS 2.57,1.157 2.955,1.301 0.385,0.144 10 CLTE 2.532,1.228 1.835,1.228 false 1.842,1.367 2.527,1.859 false 0.331,0.469 0.639,0.651 0.309,0.181 10 H19

Reconnect the H19 automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.

Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor)


c.
B113714E01
2.948,1.063 3.292,1.219 0.344,0.156 10 GND 1.844,1.177 1.969,1.333 0.125,0.156 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
H19-5 (CLTS) - H19-3 (CLTE) 5 V/DIV., 5 ms./DIV. Ignition switch ON
Headlight dimmer switch AUTO Automatic light control sensor covered with a hand → Automatic light control sensor exposed to ambient light
Correct waveform is as shown


HINT:

When the ambient light becomes brighter, width A becomes narrower.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR