Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261275 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU receives headlight dimmer switch information signals and illuminates the clearance lights, taillights and license plate lights.

WIRING DIAGRAM

E199766E10
5.458,3.5 5.615,3.656 0.156,0.156 10 false A 5.458,3.656 7.135,4.021 1.677,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 5.844,1.177 6.052,1.344 0.208,0.167 10 false 14 6.167,1.26 6.583,1.427 0.417,0.167 10 false TRLY 3.938,1.979 4.292,2.146 0.354,0.167 10 false TAIL 4.667,2.5 5.021,2.667 0.354,0.167 10 false TAIL 0.604,1.24 1.469,1.438 0.865,0.198 10 false from Battery 0.125,2.292 1.385,2.469 1.26,0.177 10 false to Clearance Lights 0.115,2.781 1.438,3.167 1.323,0.385 10 false to Taillights and License Plate Lights 2.167,1.26 2.385,1.417 0.219,0.156 10 false 2K 2.208,1.073 2.344,1.24 0.135,0.167 10 false 1 2.167,2.333 2.385,2.49 0.219,0.156 10 false 2F 2.208,2.146 2.344,2.313 0.135,0.167 10 false 7 2.167,2.906 2.385,3.063 0.219,0.156 10 false 2D 2.167,2.719 2.354,2.885 0.188,0.167 10 false 32 2.771,3.385 5.146,3.573 2.375,0.188 10 false Driver Side Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TAILLIGHT RELAY)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay ON/OFF -

OK:

Taillight relay operates (taillights illuminate).




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU)
2.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU)
a.
U116502E01
0.162,0.098 0.366,0.275 0.205,0.177 10 *a 1.666,0.53 1.811,0.686 0.145,0.156 10 A 0.879,1.389 1.274,1.558 0.395,0.170 10 TRLY 1.495,1.109 1.398,1.47 1.398,1.47 1.329,1.47 false

Remove the main body ECU (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-14(TRLY) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU)



OK

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
U170727E01
1.621,0.294 1.812,0.449 0.191,0.156 10 2K 1.686,1.913 1.876,2.069 0.191,0.156 10 A 1.892,3.002 2.268,3.158 0.376,0.156 10 TRLY 1.507,2.605 1.661,3.075 1.661,3.075 1.833,3.075 false

a.

Remove the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-14(TRLY) - 2K-1 Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY