w/o Air Suspension System:
The DTC is stored when the headlight swivel ECU detects malfunctions in the rear height control sensor power source or rear height control sensor.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2416 | ·
Malfunction in the rear height control sensor. ·
Open or short in the rear height control sensor circuit. |
·
Rear height control sensor sub-assembly ·
Headlight swivel ECU assembly ·
Harness or connector |
| B241A | ·
Malfunction in the rear height control sensor. ·
Open or short in the rear height control sensor circuit. |
·
Rear height control sensor sub-assembly ·
Headlight swivel ECU assembly ·
Harness or connector |
w/ Air Suspension System:
The DTC is stored when the headlight swivel ECU detects malfunctions in the suspension control ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2416 | ·
Malfunction in the suspension control ECU. ·
Open or short in the suspension control ECU circuit. |
·
Air suspension system ·
Suspension control ECU ·
Headlight swivel ECU assembly ·
Harness or connector |
| B241A | ·
Malfunction in the suspension control ECU. ·
Open or short in the suspension control ECU circuit. |
·
Air suspension system ·
Suspension control ECU ·
Headlight swivel ECU assembly ·
Harness or connector |
Clear the DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
DTC B2416 or B241A output does not occur.
OK
NG
Check the vehicle equipment.
| Result | Proceed to |
|---|---|
| w/o Air Suspension System | A |
| w/ Air Suspension System | B |
A
B
Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Height Sens Pw Supply Val | Height control sensor power supply value / 0 to 6.25 V | Approximately 5 V | - |
| Rr Height Sens Signal Val | Rear height control sensor signal value / 0 to 5 V | 0.5 to 4.5 V | The value changes according to the vehicle height. |
Normal conditions listed above are displayed.
OK
NG
Disconnect the A58 headlight swivel ECU connector.
Disconnect the S3 rear height control sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-18 (SBF) - S3-1 (SHB) | Always | Below 1 Ω |
| A58-19 (SHRL) - S3-2 (SHRR) | Always | Below 1 Ω |
| A58-21 (SGF) - S3-3 (SHG) | Always | Below 1 Ω |
| A58-18 (SBF) - Body ground | Always | 10 kΩ or higher |
| A58-19 (SHRL) - Body ground | Always | 10 kΩ or higher |
| A58-21 (SGF) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the rear height control sensor (See page Vehicle Exterior>LIGHTING (EXT)>HEIGHT CONTROL SENSOR>REMOVAL).
| *a | Min. Low | *b | Normal |
| *c | Max. High | - | - |
|
45° |
|
45° |
Connect 3 dry cell batteries (1.5 V) in series.
Connect the positive (+) end of the batteries to terminal 1 (SHB) of the height control sensor and the negative (-) end of the batteries to terminal 3 (SHG). While slowly moving the sensor link up and down, measure the voltage between terminal 2 (SHRR) and terminal 3 (SHG).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (SHG) - 2 (SHRR) | Max. high (45°) | 4.4 to 4.6 V |
| Normal (0°) | 2.3 to 2.6 V | |
| Min. low (-45°) | 0.4 to 0.6 V |
Do not apply a voltage of 5 V or higher.
OK
NG
Check for DTCs (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>DTC CHECK / CLEAR).
DTC "C1712 Front Height Control Sensor LH Circuit Malfunction" and "C1714 Rear Height Control Sensor LH Circuit Malfunction" are not output.
OK
NG
Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Height Sens Pw Supply Val | Height control sensor power supply value / 0 to 6.25 V | Approximately 5 V | - |
| Rr Height Sens Signal Val | Rear height control sensor signal value / 0 to 5 V | 0.5 to 4.5 V | The value changes according to the vehicle height. |
Normal conditions listed above are displayed.
OK
NG
Disconnect the A58 headlight swivel ECU connector.
Disconnect the A14 and R19 suspension control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-18 (SBF) - A14-22 (SBL) | Always | Below 1 Ω |
| A58-19 (SHRL) - R19-27 (SHR2) | Always | Below 1 Ω |
| A58-21 (SGF) - A14-21 (SGL) | Always | Below 1 Ω |
| A58-18 (SBF) - Body ground | Always | 10 kΩ or higher |
| A58-19 (SHRL) - Body ground | Always | 10 kΩ or higher |
| A58-21 (SGF) - Body ground | Always | 10 kΩ or higher |
OK
NG
Temporarily replace the suspension control ECU with a new or normally functioning one (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL ECU>REMOVAL).
Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).
DTC B2416 or B241A output does not occur.
OK
NG