Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261275 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

The illumination of the low beam headlights is controlled by the main body ECU. When the headlights are turned on, the main body ECU receives a signal from the headlight assembly and detects the illumination condition of the low beam headlights.

DTC Code DTC Detection Condition Trouble Area
B2430 LED headlight LH circuit malfunction
·

Headlight unit LH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


B2431 LED headlight RH circuit malfunction
·

Headlight unit RH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



HINT:

DTC B2430 and B2431 are not output if 12 seconds have not elapsed since the ignition switch was turned ON.


WIRING DIAGRAM

E285372E01
5.47,6.846 7.110,7.213 1.640,0.367 10 Main Body ECU (Multiplex Network Body ECU) 4.522,1.774 5.796,2.141 1.274,0.367 10 Driver Side Junction Block Assembly 5.553,0.874 5.765,1.044 0.211,0.170 10 15 4.272,0.994 4.484,1.164 0.211,0.170 10 40 5.953,1.095 6.372,1.265 0.420,0.170 10 HRLY 2.069,1.283 2.620,1.453 0.552,0.170 10 H-LP HI 3.724,0.977 3.879,1.142 0.156,0.165 10 2 3.745,1.87 3.901,2.035 0.156,0.165 10 3 2.967,1.873 3.123,2.038 0.156,0.165 10 5 2.96,1 3.116,1.165 0.156,0.165 10 1 0.497,1.965 1.342,2.167 0.845,0.202 10 from Battery 3.055,5.962 3.893,6.132 0.838,0.170 10 H-LP RH-LO 0.971,6.629 2.522,6.869 1.552,0.239 10 Headlight Unit RH 0.971,6.49 1.277,6.646 0.306,0.156 10 A87 5.61,5.909 5.732,6.079 0.121,0.170 10 8 3.065,4.305 3.902,4.475 0.838,0.170 10 H-LP LH-LO 1.11,3.928 1.323,4.084 0.213,0.156 10 LO 2.418,3.758 2.578,3.914 0.161,0.156 10 S 1.013,4.626 2.564,4.866 1.552,0.239 10 Headlight Unit LH 1.013,4.487 1.319,4.643 0.306,0.156 10 A86 3.127,2.413 3.780,2.583 0.654,0.170 10 H-LP LO 5.596,1.082 5.757,1.238 0.161,0.156 10 A 5.925,6.116 6.356,6.272 0.431,0.156 10 RLEW 5.925,3.776 6.356,3.932 0.431,0.156 10 LLEW 5.594,3.547 5.786,3.703 0.193,0.156 10 21 5.519,3.767 5.846,3.923 0.327,0.156 10 G64 0.894,3.817 1.049,3.983 0.156,0.165 10 2 2.642,3.662 2.853,3.832 0.211,0.170 10 3 2.418,4.069 2.629,4.239 0.211,0.170 10 B 2.642,3.999 2.853,4.168 0.211,0.170 10 1 5.519,6.107 5.846,6.263 0.327,0.156 10 G64 4.515,1.597 4.727,1.767 0.211,0.170 10 2F 0.236,1.096 1.315,1.266 1.080,0.170 10 to H-LP HI Relay 1.105,5.95 1.318,6.106 0.213,0.156 10 LO 2.413,6.116 2.573,6.272 0.161,0.156 10 S 0.889,5.84 1.045,6.005 0.156,0.165 10 2 2.637,6.021 2.849,6.191 0.211,0.170 10 3 2.413,5.769 2.624,5.939 0.211,0.170 10 B 2.637,5.699 2.849,5.868 0.211,0.170 10 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 output does not occur.




OK

NG

3.INSPECT HEADLIGHT RELAY (H-LP LO)
3.INSPECT HEADLIGHT RELAY (H-LP LO)
a.
E108359E19
2.313,0.792 2.75,0.552 false 2.323,1.458 2.24,1.75 false 2.083,1.167 1.927,1.479 false 2.531,1.073 2.771,1.25 false 1.583,0.708 1.708,0.906 0.125,0.198 10 false 3 1.583,1.26 1.708,1.458 0.125,0.198 10 false 2 2.781,0.417 2.906,0.615 0.125,0.198 10 false 3 2.802,1.135 2.927,1.333 0.125,0.198 10 false 1 2.167,1.74 2.302,1.938 0.135,0.198 10 false 5 1.823,1.438 1.948,1.635 0.125,0.198 10 false 2 0.5,1.26 0.625,1.458 0.125,0.198 10 false 1 0.5,0.708 0.635,0.906 0.135,0.198 10 false 5

Remove the headlight relay from the engine room relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage applied between terminals 1 and 2 Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY)

NG

REPLACE HEADLIGHT RELAY (H-LP LO)

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - BATTERY)
a.
E199762E01
0.375,0.153 0.586,0.323 0.211,0.170 10 *a

Remove the headlight relay from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay terminal 5 - Body ground Always 11 to 14 V
Headlight relay terminal 1 - Body ground


Text in Illustration
*a Front view of wire harness connector
(to Headlight Relay [H-LP LO])



OK

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Remove the headlight relay from the engine room relay block assembly.


b.

Disconnect the 2F driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 2 - 2F-40 Always Below 1 Ω
2F-40 - Body ground Always 10 kΩ or higher




OK

6.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.
U116636E01
1.573,2.552 1.719,2.938 1.719,2.938 1.875,2.938 false 1.635,2.135 1.781,2.323 0.146,0.188 10 false A 0.448,0.958 0.677,1.104 0.229,0.146 10 false 2F 1.958,2.875 2.396,3.063 0.438,0.188 10 false HRLY

Remove the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-15 (HRLY) - 2F-40 Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - HEADLIGHT)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - HEADLIGHT)

*1: for LH

*2: for RH


a.

Remove the headlight relay from the engine room relay block assembly.


b.

Disconnect the A86*1 and A87*2 headlight connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 3 - A86-1 (B)*1 Always Below 1 Ω
Headlight relay terminal 3 - A87-1 (B)*2 Always Below 1 Ω
Headlight relay terminal 3 - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT - MAIN BODY ECU AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the A86*1 or A87*2 headlight unit connector.

*1: for LH

*2: for RH



b.

Disconnect the G64 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH:
Tester Connection Condition Specified Condition
A86-3 (S) - G64-21 (LLEW) Always Below 1 Ω
A86-2 (LO) - Body ground Below 1 Ω
A86-3 (S) - Body ground 10 kΩ or higher

for RH:
Tester Connection Condition Specified Condition
A87-3 (S) - G46-8 (RLEW) Always Below 1 Ω
A87-2 (LO) - Body ground Below 1 Ω
A87-3 (S) - Body ground 10 kΩ or higher




OK

9.CHECK HEADLIGHT UNIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HEADLIGHT UNIT
a.

Temporarily replace the headlight with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 output does not occur.




OK

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)