Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261300 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 89997 1.INSTALL ELECTRICAL KEY ANTENNA (w/ Entry and Start System)

a.

Install the electrical key antenna with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52186B 2.INSTALL REAR BUMPER SIDE MOUNTING BRACKET LH

a.

Connect the connector.


b.

Install the rear bumper side mounting bracket with the bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52185B 3.INSTALL REAR BUMPER SIDE MOUNTING BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 52158C 4.INSTALL NO. 2 REAR BUMPER SIDE SUPPORT LH

a.

Install the No. 2 rear bumper side support with the bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52174D 5.INSTALL REAR BUMPER BAR REINFORCEMENT LH

a.

Install the rear bumper bar reinforcement with the 3 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 52173D 6.INSTALL REAR BUMPER BAR REINFORCEMENT RH

HINT:

Use the same procedure described for the LH side.


Hide 52588 7.INSTALL REAR BUMPER END RETAINER LH (w/ Rear Bumper End Retainer)

a.

Install the rear bumper end retainer with the screw.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


Hide 52587 8.INSTALL REAR BUMPER END RETAINER RH (w/ Rear Bumper End Retainer)

HINT:

Use the same procedure described for the LH side.


Hide 52156A 9.INSTALL REAR BUMPER SIDE SUPPORT LH

a.

Attach the 4 claws to install the rear bumper side support.


b.

Install the 3 screws.


Hide 52155A 10.INSTALL REAR BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 52169A 11.INSTALL NO. 3 REAR BUMPER SIDE SUPPORT

a.

Install the No. 3 rear bumper side support with the screw.

Torque:
3.0 N*m (31 kgf*cm, 27 ft.*lbf)


Hide 52159 12.INSTALL REAR BUMPER COVER (for 5 Door)

a.

w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:

Connect the 4 connectors.


b.

w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:

Connect the 2 connectors.


c.

w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:

Connect the 2 connectors.


d.

Attach the 14 claws to install the rear bumper cover.


e.

Install the 5 bolts and 2 clips.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 52159 13.INSTALL REAR BUMPER COVER (for 3 Door)

a.

w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:

Connect the 4 connectors.


b.

w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:

Connect the 2 connectors.


c.

w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:

Connect the 2 connectors.


d.

Attach the 10 claws to install the rear bumper cover.


e.

Install the 5 bolts and 2 clips.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 76626E 14.INSTALL REAR QUARTER PANEL MUDGUARD LH

Hide 76625G 15.INSTALL REAR QUARTER PANEL MUDGUARD RH

HINT:

Use the same procedure described for the LH side.


Hide 52162B 16.INSTALL NO. 1 REAR BUMPER PLATE

a.

Attach the 21 claws to install the No. 1 rear bumper plate.


b.

Install the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 69411 17.INSTALL BACK DOOR CHECK

Hide 52179B 18.INSTALL REAR BUMPER BAR PLATE

a.

Attach the 14 claws to install the rear bumper bar plate.


Hide 58766A 19.INSTALL JACK BOX HOLE COVER

a.

Attach the 2 claws to install the jack box hole cover.


Hide 51980 20.INSTALL PINTLE HOOK ASSEMBLY (w/ Pintle Hook)

a.

Install the pintle hook with the 4 bolts and 4 nuts.

Torque:
81 N*m (826 kgf*cm, 60 ft.*lbf)


b.

For vehicles with a spare tire installed to the underbody, install the spare tire.