Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261300 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).

·

When installing the rear bumper pad and rear bumper energy absorber, heat the rear bumper cover surface using a heat light.

Standard:
Item Temperature
Rear Bumper Cover 20 to 30°C (68 to 86°F)




NOTICE:

Do not heat the rear bumper cover excessively.


PROCEDURE

Hide 52461F 1.INSTALL REAR BUMPER PAD (for 5 Door)

a.

When using a new rear bumper cover:

i.

Clean the rear bumper cover surface.


ii.

Using a heat light, heat the rear bumper cover surface.



b.

When reusing the rear bumper cover:

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove the double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



c.

Install a new rear bumper pad.

i.

Remove the peeling paper from the face of a new rear bumper pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Align the rear bumper pad with the mark-off line of the rear bumper.


iii.

Install the 4 rear bumper pads.



Hide 52461F 2.INSTALL REAR BUMPER PAD (for 3 Door)

a.

When using a new rear bumper cover:

i.

Clean the rear bumper cover surface.


ii.

Using a heat light, heat the rear bumper cover surface.



b.

When reusing the rear bumper cover:

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove the double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



c.

Install a new rear bumper pad.

i.

Remove the peeling paper from the face of a new rear bumper pad.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

Align the rear bumper pad with the mark-off line of the rear bumper.


iii.

Install the 2 rear bumper pads.



Hide 52152B 3.INSTALL REAR BUMPER EXTENSION RH

a.

Attach the claw to install the rear bumper extension.


b.

Install the screw.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 81920 4.INSTALL REFLEX REFLECTOR ASSEMBLY LH (w/o Rear Fog Light)

a.

Attach the 2 claws to install the reflex reflector.


b.

Install the screw.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 81910 5.INSTALL REFLEX REFLECTOR ASSEMBLY RH (w/o Rear Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 81590B 6.INSTALL REAR FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light)

Hide 81580H 7.INSTALL REAR FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light)

HINT:

Use the same procedure described for the LH side.


Hide 52046A 8.INSTALL REAR BUMPER PROTECTOR SUB-ASSEMBLY LH

a.

Install the rear bumper protector with the screw.


Hide 52045A 9.INSTALL REAR BUMPER PROTECTOR SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89348A 10.INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89341A 11.INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89348D 12.INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

Hide 82163B 13.INSTALL NO. 5 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

a.

Attach the 5 clamps to install the No. 5 floor wire.


b.

Connect the 3 connectors.


Hide 82163B 14.INSTALL NO. 5 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light)

a.

Attach the 5 clamps to install the No. 5 floor wire.


b.

Connect the 2 connectors.


Hide 82163B 15.INSTALL NO. 5 FLOOR WIRE (w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

a.

Attach the 2 clamps to install the No. 5 floor wire.


b.

Connect the connector.


Hide 82163A 16.INSTALL NO. 4 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

HINT:

Use the same procedure described for the No. 5 floor wire.


Hide 82163A 17.INSTALL NO. 4 FLOOR WIRE (w/ TOYOTA Parking Assist-sensor System, w/o Rear Fog Light)

HINT:

Use the same procedure described for the No. 5 floor wire.


Hide 82163A 18.INSTALL NO. 4 FLOOR WIRE (w/o TOYOTA Parking Assist-sensor System, w/ Rear Fog Light)

HINT:

Use the same procedure described for the No. 5 floor wire.


Hide 52615 19.INSTALL REAR BUMPER ENERGY ABSORBER

a.

When using a new rear bumper cover:

i.

Clean the rear bumper cover surface.


ii.

Using a heat light, heat the rear bumper cover surface.



b.

When reusing the rear bumper cover:

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove the double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



c.

When reusing the rear bumper energy absorber:

i.

Remove the double-sided tape from the rear bumper cover.


ii.

Wipe off any tape adhesive residue with cleaner.


iii.
B247915E02
2.229,0.323 2.313,0.323 2.313,0.323 2.375,0.729 true 2.917,1.188 2.969,1.188 2.969,1.188 2.969,0.823 true 1.781,1.198 1.708,1.198 1.708,1.198 1.688,0.99 true 1.167,0.333 1.063,0.333 1.063,0.333 1.01,0.729 true 0.479,1.198 0.354,1.198 0.354,1.198 0.281,0.813 true 0.333,1.917 0.719,2.063 0.385,0.146 10 false 2 mm 0.333,2.083 1.083,2.292 0.75,0.208 10 false (0.0787 in.) 1.438,2.573 1.948,2.719 0.51,0.146 10 false 3.0 mm 1.438,2.74 2.167,2.948 0.729,0.208 10 false (0.118 in.) 2.365,2.24 2.885,2.385 0.521,0.146 10 false 5.0 mm 2.365,2.396 3.063,2.615 0.698,0.219 10 false (0.197 in.) 0.5,1.104 0.667,1.271 0.167,0.167 10 false *1 1.823,1.115 1.99,1.281 0.167,0.167 10 false *1 2.75,1.104 2.917,1.271 0.167,0.167 10 false *1 2.073,0.25 2.24,0.417 0.167,0.167 10 false *1 1.188,0.24 1.354,0.406 0.167,0.167 10 false *1

Install the double-sided tape as shown in the illustration.



d.

Install the rear bumper energy absorber.

i.

Remove the peeling paper from the face of the rear bumper energy absorber.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.
B247882E01
1.517,0.837 1.680,0.997 0.163,0.159 10 *1 2.325,0.528 2.487,0.687 0.163,0.159 10 *1 1.517,0.939 1.372,0.939 1.372,0.939 1.31,1.475 false 2.505,0.615 2.618,0.615 2.618,0.615 2.709,1.116 false

Align the guide and install the rear bumper energy absorber to rear bumper cover as shown in the illustration.

HINT:

Press the rear bumper energy absorber firmly to install it.


Text in Illustration
*1 Guide