Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING › 2015.06–2020.08
RM27T0E _59 Vehicle Exterior _053749 EXTERIOR PANELS / TRIM _0261309 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When removing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.



Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or window frame moulding excessively.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 69298C 3.REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

Hide 74611C 4.REMOVE ASSIST GRIP COVER LH

Hide 67604 5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 68174A 6.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

Hide 67842E 7.REMOVE REAR DOOR SERVICE HOLE COVER LH

Hide 68152C 8.REMOVE REAR DOOR GLASS RUN LH

Hide 67408E 9.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Hide 68124B 10.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

Hide 68104 11.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

Hide 67872 13.REMOVE REAR DOOR WEATHERSTRIP LH

B236341

a.

Detach the clip and remove the upper part of the rear door weatherstrip so that the moulding can be removed.


Hide 75762A 14.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

a.
B243913

Remove the door window frame moulding clip.


b.
B243912E03
1.073,0.135 1.448,0.135 1.448,0.135 1.521,0.344 true 0.771,1.188 1.01,1.188 1.01,1.188 1.208,1.281 true 1.135,1.76 0.656,1.76 true 1.417,1.927 1.75,1.927 true 2.469,2.302 2.313,2.302 2.313,2.302 2.135,2.781 true 0.885,0.052 1.052,0.219 0.167,0.167 10 false *1 2.469,2.198 2.635,2.365 0.167,0.167 10 false *1 0.448,1.667 0.615,1.844 0.167,0.177 10 false *2 1.75,1.833 1.917,2.01 0.167,0.177 10 false *2 0.573,1.104 0.75,1.25 0.177,0.146 10 false *3

Put protective tape around the rear door front window frame moulding.


c.

Using a moulding remover, detach the clip and remove the double-sided tape to remove the rear door front window frame moulding.

Text in Illustration
*1 Protective Tape
*2 Double-sided Tape
*3 Moulding Remover