Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2015.06–2020.08
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261248 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 69298A 2.REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.
B239600

Using moulding remover A, detach the 3 claws and remove the rear door inside handle bezel as shown in the illustration.


Hide 74611C 3.REMOVE ASSIST GRIP COVER LH

a.
B239602

Using moulding remover A, detach the 8 claws and remove the assist grip cover.


Hide 67604 4.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B239604

Remove the 3 screws.


b.

Using a clip remover, detach the 9 clips.


c.
B239606

Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.


d.

Raise the rear door trim board sub-assembly to detach the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.


e.
B239612

Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.


f.
B239616E04
0.063,0.052 0.302,0.302 0.24,0.25 10 false *A 0.073,2.188 0.354,2.438 0.281,0.25 10 false *B

Disconnect each connector.

Text in Illustration
*A for 14 Speakers
*B for 9 Speakers


g.
B241320

Using a screwdriver, detach the claw and remove the clamp.


Hide 68174A 5.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B239615

Using a screwdriver, detach the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.


Hide 84810D 6.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 81910D 7.REMOVE REAR REFLEX REFLECTOR ASSEMBLY

a.
E198065

Detach the 2 claws and remove the rear reflex reflector assembly.


Hide 81080G 8.REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

Hide 81081A 9.REMOVE NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

Hide 69206C 10.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B239610

Remove the 8 screws and rear door armrest.


b.
B239618

Remove the 2 screws.


c.

Detach the guide and 2 claws and remove the rear door inside handle sub-assembly from the rear door trim board sub-assembly.


Hide 86160Y 11.REMOVE REAR NO. 2 SPEAKER ASSEMBLY (for 14 Speakers)

Hide 67842E 13.REMOVE REAR DOOR SERVICE HOLE COVER

a.
B239620

Disconnect the connector.


b.

Detach the 3 clamps, move the wire harness out of the way and remove the service hole cover.

HINT:

Remove any remaining butyl tape from the door.



Hide 68152C 14.REMOVE REAR DOOR GLASS RUN LH

a.
B239628

Remove the rear door glass run.


Hide 67674A 15.REMOVE REAR DOOR FRAME GARNISH LH

a.
B240621

Detach the clip and remove the rear door frame garnish.


Hide 67408E 16.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.
B239630E01
2.477,1.092 2.681,1.283 0.204,0.191 10 *1 2.438,1.185 2.036,1.185 2.036,1.185 1.781,1.862 false

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt


b.

Remove the 2 bolts and screw.


c.

Remove the rear door window division bar sub-assembly.


d.

Remove the temporary bolt from the rear door window division bar sub-assembly.


Hide 68124B 17.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

a.
B239632

Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.


Hide 68189 18.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.
B241321

Remove the rear door quarter window weatherstrip from the rear door quarter window glass.


Hide 68104 19.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.


b.

Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the power window regulator switch assembly and rear power window regulator motor connectors.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




e.
B239636

Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

NOTICE:

After the bolts are removed, do not allow the door glass to fall.



f.
B239640E03
2.802,0.188 3.042,0.406 0.24,0.219 10 true (1) 1.479,0.031 1.792,0.25 0.313,0.219 10 false (2)

Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 69906B 20.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

a.
B234457E02
0.917,0.802 1.087,0.965 0.170,0.163 10 *1 0.602,1.212 0.686,0.893 0.686,0.893 0.883,0.893 false

Using a screwdriver, remove the rear door glass channel sub-assembly.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 69975A 21.REMOVE REAR DOOR GLASS CHANNEL FILLER

a.

Remove the rear door glass channel filler.


Hide 69840A 22.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH

a.
B239642E06
1.438,0.813 1.885,0.813 1.885,0.813 1.979,1.208 true 1.24,0.719 1.469,0.938 0.229,0.219 10 true *1

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.



b.

Remove the 3 bolts.


c.

Remove the rear door window regulator assembly.


d.

Remove the temporary bolt from the rear door window regulator assembly.


Hide 85720C 23.REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69340 24.REMOVE REAR DOOR LOCK ASSEMBLY LH

Hide 69740D 25.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B239650E03
0.037,0 0.295,0.331 0.258,0.331 10 *A 0.037,2.067 0.333,2.398 0.296,0.331 10 *B

Using a screwdriver, detach the claw.

Text in Illustration
*A w/ Double Locking System
*B w/o Double Locking System

HINT:

Tape the screwdriver tip before use.



b.
B239652E04
0.037,0 0.367,0.331 0.329,0.331 10 *A 0.037,2.155 0.326,2.486 0.289,0.331 10 *B

Remove the rear door lock remote control cable assembly.

Text in Illustration
*A w/ Double Locking System
*B w/o Double Locking System


Hide 69780B 26.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B239654E03
0.037,0 0.260,0.331 0.223,0.331 10 *A 0.037,2.101 0.296,2.433 0.259,0.331 10 *B

Using a screwdriver, detach the 3 claws.

Text in Illustration
*A w/ Double Locking System
*B w/o Double Locking System

HINT:

Tape the screwdriver tip before use.



b.
B239656E02
0.037,0 0.340,0.331 0.303,0.331 10 *A 0.037,2.101 0.278,2.433 0.241,0.331 10 *B

Remove the rear door inside locking cable assembly.

Text in Illustration
*A w/ Double Locking System
*B w/o Double Locking System


Hide 69227L 27.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

a.
B449821

Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.



b.

Detach the claw and remove the rear door outside handle cover.


Hide 69240 28.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B239662

Move the lever in the direction indicated by the arrow in the illustration.


b.
B239664

Remove the rear door outside handle assembly as shown in the illustration.


Hide 69252B 29.REMOVE REAR DOOR NO. 1 OUTSIDE HANDLE PAD LH

a.
B239668

Detach the 3 claws and remove the rear door No. 1 outside handle pad.


Hide 69254B 30.REMOVE REAR DOOR NO. 2 OUTSIDE HANDLE PAD LH

a.
B239670

Detach the 2 claws and remove the rear door No. 2 outside handle pad.


Hide 69204A 31.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B239672

Using a T30 "TORX" socket wrench, loosen the screw.


b.

Slide the rear door outside handle frame sub-assembly to detach the door handle nut and claw of the rear door outside handle frame sub-assembly, and then remove the rear door outside handle frame sub-assembly.


Hide 67888A 32.REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH

a.
B239676

Using a clip remover, detach the 6 clips and guide and remove the rear door No. 2 weatherstrip as shown in the illustration.


Hide 68640A 33.REMOVE REAR DOOR CHECK ASSEMBLY LH

a.
B239622

Remove the bolt, 2 nuts and rear door check assembly.


Hide 67872 34.REMOVE REAR DOOR WEATHERSTRIP LH

a.
B239624

Using a clip remover, detach the 19 clips and guide and remove the rear door weatherstrip.


Hide 75762A 36.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

Hide 75978H 38.REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH

Hide 67003C 41.REMOVE REAR DOOR PANEL CUSHION

a.
B240622

Using a clip remover, detach the clip and remove the door panel cushion.