Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2016.08–2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1570  Red LED Error  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (red) circuit of the manual (SOS) switch.

The manual (SOS) switch indicator (red) illuminates for 10 seconds and turns off when the ignition switch is turned to ON.

If a malfunction in the telematics system is detected, the manual (SOS) switch indicator (red) will illuminate. However, the manual (SOS) switch indicator (red) may not illuminate when this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1570 Red LED Error Current for the manual (SOS) switch indicator (red) exceeds malfunction threshold for 20 seconds when the ignition switch is ON.
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Wire harness or connector



WIRING DIAGRAM

E355991E01
1.417,1.74 2.927,1.979 1.51,0.24 10 false Manual (SOS) Switch 3.385,1.094 3.875,1.344 0.49,0.25 10 false GND1 3.385,1.469 3.875,1.719 0.49,0.25 10 false GND2 3.844,1.094 4.104,1.333 0.26,0.24 10 false 15 3.854,1.49 4.115,1.729 0.26,0.24 10 false 16 1.896,0.99 2.385,1.24 0.49,0.25 10 false RED 1.042,2.313 2.552,2.552 1.51,0.24 10 false Map Light Assembly 1.042,2.135 1.531,2.385 0.49,0.25 10 false W7 5.156,0.792 5.646,1.042 0.49,0.25 10 false IND1 3.458,0.667 3.948,0.917 0.49,0.25 10 false IND1 3.833,0.667 4.094,0.906 0.26,0.24 10 false 19 4.927,0.677 5.188,0.917 0.26,0.24 10 false 11 4.906,1.896 6.417,2.135 1.51,0.24 10 false Telematics Transceiver 4.896,1.729 5.385,1.979 0.49,0.25 10 false G187

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


HINT:

If DTC B1570 is stored, the manual (SOS) switch indicator (red) may not illuminate when another DTC is stored.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) (RED INDICATOR)
a.
E140936C07
2.646,1.594 2.771,1.979 2.771,1.979 2.906,1.979 true 1.521,1.979 1.677,1.979 1.677,1.979 2.094,1.594 true 2.281,2.021 2.438,2.021 2.438,2.021 2.5,1.594 true 2.948,1.906 3.385,2.115 0.438,0.208 10 false GND1 1.167,1.896 1.781,2.094 0.615,0.198 10 false IND1 0.167,0.146 0.781,0.344 0.615,0.198 10 false *a 1.875,1.938 2.49,2.135 0.615,0.198 10 false GND2
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Front Door)>REMOVAL


b.

Connect 2 dry-cell batteries (1.5 V each) in series.


c.

Connect a positive (+) lead from the batteries to terminal 19 (IND1) and a negative (-) lead to terminal 15 (GND1) or terminal 16 (GND2) of the map light assembly (manual (SOS) switch) connector.


d.

Check if the manual (SOS) switch indicator (red) illuminates.

OK:

Manual (SOS) switch indicator (red) illuminates.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) - TELEMATICS TRANSCEIVER AND BODY GROUND)

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH) - TELEMATICS TRANSCEIVER AND BODY GROUND)
a.

Disconnect the G187 telematics transceiver connector.


b.

Disconnect the W7 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-11 (IND1) - W7-19 (IND1) Always Below 1 Ω
G187-11 (IND1) or W7-19 (IND1) - Body ground Always 10 kΩ or higher
W7-15 (GND1) - Body ground Always Below 1 Ω
W7-16 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT