Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2016.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C5  Emergency Switch Error (Open or Short)  


DESCRIPTION

This DTC is stored when the telematics transceiver detects an open or short circuit in the manual (SOS) switch.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C5 Emergency Switch Error (Open or Short) Open or short circuit in the manual (SOS) switch is detected.
·

Telematics transceiver

·

Map light assembly (manual (SOS) switch)

·

Wire harness or connector



WIRING DIAGRAM

E353339E01
1.063,2.198 2.531,2.417 1.469,0.219 10 false Map Light Assembly 1.052,2.01 1.365,2.208 0.313,0.198 10 false W7 1.51,1.615 2.979,1.833 1.469,0.219 10 false Manual (SOS) Switch 3.469,1.083 3.854,1.271 0.385,0.188 10 false GND 3.438,0.542 3.823,0.729 0.385,0.188 10 false SIG2 3.875,0.542 4.26,0.729 0.385,0.188 10 false 20 3.896,1.083 4.281,1.271 0.385,0.188 10 false 3 5.167,0.625 5.552,0.813 0.385,0.188 10 false SIG1 5.177,1.094 5.563,1.281 0.385,0.188 10 false SIG- 4.896,1.094 5.281,1.281 0.385,0.188 10 false 26 4.885,0.542 5.271,0.729 0.385,0.188 10 false 27 5.052,1.938 6.552,2.167 1.5,0.229 10 false Telematics Transceiver 5.031,1.76 5.396,1.969 0.365,0.208 10 false G187

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.

Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Front Door)>REMOVAL


b.
E140936C10
1.948,1.604 2.094,2.01 true 2.344,1.365 2.594,0.833 true 2.625,0.708 3.24,0.906 0.615,0.198 10 false GND 2.156,1.938 2.771,2.135 0.615,0.198 10 false SIG2 0.188,0.167 0.802,0.365 0.615,0.198 10 false *a
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
20 (SIG2) - 3 (GND) Manual (SOS) switch not pressed 392 to 432 Ω
20 (SIG2) - 3 (GND) Manual (SOS) switch pressed 78 to 86 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))

NG

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the G187 telematics transceiver connector.


b.

Disconnect the W7 map light assembly (manual (SOS) switch) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-27 (SIG1) - W7-20 (SIG2) Always Below 1 Ω
G187-26 (SIG-) - W7-3 (GND) Always Below 1 Ω
G187-27 (SIG1) or W7-20 (SIG2) - Body ground Always 10 kΩ or higher
G187-26 (SIG-) or W7-3 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT