Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2016.08–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) U

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  TERMINALS OF ECU  


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the engine switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





JUNCTION CONNECTOR


a.

No. 1 Junction Connector

i.

G193 No. 1 junction connector

U148556E04
2.885,1.073 3.021,1.073 3.021,1.073 3.563,1.875 false 3.698,1.854 3.198,0.885 3.198,0.885 3.063,0.885 false 4.198,1.865 4.552,1.708 4.552,1.708 4.667,1.708 false 4.594,1.5 4.458,1.5 4.458,1.5 4.073,1.865 false 3.958,1.854 4.354,1.26 4.354,1.26 4.49,1.26 false 3.021,2.594 3.156,2.594 3.156,2.594 3.583,2.094 false 3.708,2.104 3.365,2.823 3.365,2.823 3.229,2.823 false 4.198,2.094 4.469,2.302 4.469,2.302 4.573,2.302 false 4.51,2.51 4.375,2.51 4.375,2.51 4.073,2.094 false 3.958,2.094 4.313,2.74 4.313,2.74 4.448,2.74 false 3.844,2.094 4.146,3 4.146,3 4.323,3 false 3.823,1.865 4.208,1.01 4.208,1.01 4.385,1.01 false 2.625,1.375 2.76,1.375 2.76,1.375 3.438,1.906 false 2.594,2.375 2.729,2.375 2.729,2.375 3.438,2.073 false 3.406,0.542 3.802,0.74 0.396,0.198 10 false G193 4.615,2.229 5.229,2.396 0.615,0.167 10 false CANL*a 2.333,1 2.99,1.302 0.656,0.302 10 false CANH*f 4.708,1.646 5.313,1.844 0.604,0.198 10 false CANH*a 2.521,2.51 3.104,2.729 0.583,0.219 10 false CANL*f 4.427,0.927 5.052,1.104 0.625,0.177 10 false CANH*d 2.49,0.802 3.104,1.021 0.615,0.219 10 false CANH*e 4.354,2.927 4.979,3.083 0.625,0.156 10 false CANL*d 2.708,2.74 3.26,2.917 0.552,0.177 10 false CANL*e 4.5,2.677 5.115,2.854 0.615,0.177 10 false CANL*c 4.531,1.188 5.167,1.375 0.635,0.188 10 false CANH*c 4.635,1.417 5.281,1.604 0.646,0.188 10 false CANH*b 4.552,2.438 5.156,2.646 0.604,0.208 10 false CANL*b 2.083,1.292 2.74,1.594 0.656,0.302 10 false CANH*g 2.073,2.292 2.656,2.51 0.583,0.219 10 false CANL*g

Text in Illustration
*a for No. 2 Junction Connector *b for Four Wheel Drive Control ECU
*c for Certification ECU (Smart Key ECU Assembly) *d for Power Management Control ECU (V1 Bus)
*e for Power Steering ECU Assembly *f
·

for ECM (for 1GR-FE, 1KD-FTV, 1GD-FTV) (V1 Bus)

·

for No. 4 Junction Connector (for 2TR-FE)


*g for Telematics Transceiver (w/ Telematics Transceiver) - -

No. 1 Junction Connector Wiring Color Connect to
G193-1 (CANH) GR No. 2 junction connector
G193-12 (CANL) W
G193-2 (CANH) G Four wheel drive control ECU
G193-13 (CANL) W
G193-3 (CANH) P Certification ECU (smart key ECU assembly)
G193-14 (CANL) W
G193-4 (CANH) BR Power management control ECU (V1 bus)
G193-15 (CANL) W
G193-5 (CANH) L Power steering ECU assembly
G193-16 (CANL) W
G193-6 (CANH) R
·

ECM*1 (V1 bus)

·

No. 4 junction connector*2


G193-17 (CANL) W
G193-7 (CANH) B Telematics transceiver*3
G193-18 (CANL) W

*1: for 1GR-FE, 1KD-FTV, 1GD-FTV

*2: for 2TR-FE

*3: w/ Telematics Transceiver



ii.

G98 No. 1 junction connector

U170140E02
2.948,1.854 2.563,1.448 2.563,1.448 2.448,1.448 false 2.531,1.219 2.656,1.219 2.656,1.219 3.083,1.854 false 3.208,1.854 2.844,1.01 2.844,1.01 2.708,1.01 false 4.198,1.865 4.448,1.667 4.448,1.667 4.563,1.667 false 4.531,1.49 4.396,1.49 4.396,1.49 4.073,1.854 false 2.969,2.104 2.75,2.448 2.75,2.448 2.646,2.448 false 2.771,2.656 2.896,2.656 2.896,2.656 3.104,2.104 false 3.229,2.104 3.115,2.875 3.115,2.875 2.979,2.875 false 4.208,2.104 4.5,2.271 4.5,2.271 4.604,2.271 false 4.552,2.479 4.417,2.479 4.417,2.479 4.094,2.104 false 3.979,2.104 4.365,2.792 4.365,2.792 4.542,2.792 false 3.958,1.854 4.333,1.26 4.333,1.26 4.51,1.26 false 3.854,2.104 4.24,3.042 4.24,3.042 4.417,3.042 false 3.823,1.854 4.208,1.042 4.208,1.042 4.385,1.042 false 3.698,1.854 4.125,0.781 4.125,0.781 4.333,0.781 false 3.583,1.865 4.063,0.552 4.063,0.552 4.271,0.552 false 3.719,2.083 4.156,3.229 4.156,3.229 4.365,3.229 false 3.719,2.083 4.156,3.229 4.156,3.229 4.365,3.229 false 3.594,2.083 4.073,3.448 4.073,3.448 4.271,3.448 false 3.594,2.083 4.073,3.448 4.073,3.448 4.271,3.448 false 3.458,0.542 3.802,0.729 0.344,0.188 10 false G98 4.646,2.198 5.271,2.406 0.625,0.208 10 false CANL*a 1.99,1.135 2.604,1.302 0.615,0.167 10 false CANH*h 4.594,1.604 5.25,1.781 0.656,0.177 10 false CANH*a 2.25,2.563 2.844,2.781 0.594,0.219 10 false CANL*h 2.156,0.917 2.74,1.125 0.583,0.208 10 false CANH*g 2.458,2.771 3.052,2.99 0.594,0.219 10 false CANL*g 1.896,1.365 2.51,1.604 0.615,0.24 10 false CANH*i 2.156,2.354 2.771,2.542 0.615,0.188 10 false CANL*i 4.573,1.417 5.188,1.604 0.615,0.188 10 false CANH*b 4.594,2.417 5.135,2.615 0.542,0.198 10 false CANL*b 4.552,1.188 5.198,1.438 0.646,0.25 10 false CANH*c 4.573,2.729 5.188,2.917 0.615,0.188 10 false CANL*c 4.427,0.979 5.063,1.177 0.635,0.198 10 false CANH*d 4.438,2.969 5.042,3.167 0.604,0.198 10 false CANL*d 4.375,0.708 5.031,0.875 0.656,0.167 10 false CANH*e 4.323,0.469 4.958,0.667 0.635,0.198 10 false CANH*f 4.385,3.167 5,3.354 0.615,0.188 10 false CANL*e 4.302,3.375 4.938,3.563 0.635,0.188 10 false CANL*f

Text in Illustration
*a for No. 3 Junction Connector (V2 BUS) *b for Power Management Control ECU (V2 Bus)
*c for Parking Assist ECU (w/ Side Monitor System) *d for Driving Support ECU Assembly (w/ Pre-crash Safety System)
*e for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System) *f for Air Conditioning Amplifier Assembly (except 1KD-FTV, 1GR-FE and Manual Transmission System) (V2 Bus)
*g for ECM (Power Management Bus) *h for Air Conditioning Amplifier Assembly (for 1KD-FTV, 1GR-FE and Manual Transmission System) (Power Management Bus)
*i for Power Management Control ECU (Power Management Bus) - -

No. 1 Junction Connector Wiring Color Connect to
G98-1 (CANH) P No. 3 junction connector (V2 Bus)
G98-12 (CANL) W
G98-2 (CANH) V Power management control ECU (V2 bus)
G98-13 (CANL) W
G98-3 (CANH) B Parking assist ECU*1
G98-14 (CANL) W
G98-4 (CANH) G Driving support ECU assembly*2
G98-15 (CANL) W
G98-5 (CANH) R Clearance warning ECU assembly*3
G98-16 (CANL) W
G98-6 (CANH) BR Air conditioning amplifier assembly*5 (V2 bus)
G98-17 (CANL) W
G98-9 (CANH) BR ECM (power management bus)
G98-20 (CANL) GR
G98-10 (CANH) BR Air conditioning amplifier assembly*4 (power management bus)
G98-21 (CANL) Y
G98-11 (CANH) BR Power management control ECU (power management bus)
G98-22 (CANL) W

*1: w/ Side Monitor System

*2: w/ Pre-crash Safety System

*3: w/ TOYOTA Parking Assist-sensor System

*4: for 1KD-FTV, 1GR-FE and Manual Transmission System

*5: except 1KD-FTV, 1GR-FE and Manual Transmission System




b.

No. 2 Junction Connector

U148557E02
2.885,1.083 3.021,1.083 3.021,1.083 3.583,1.854 false 3.708,1.854 3.208,0.885 3.208,0.885 3.073,0.885 false 4.208,1.865 4.563,1.708 4.563,1.708 4.677,1.708 false 4.604,1.5 4.469,1.5 4.469,1.5 4.083,1.865 false 3.958,1.854 4.354,1.26 4.354,1.26 4.49,1.26 false 3.031,2.604 3.167,2.604 3.167,2.604 3.594,2.104 false 3.719,2.104 3.375,2.823 3.375,2.823 3.24,2.823 false 4.208,2.104 4.479,2.313 4.479,2.313 4.583,2.313 false 4.531,2.521 4.396,2.521 4.396,2.521 4.094,2.104 false 3.979,2.104 4.333,2.75 4.333,2.75 4.469,2.75 false 3.854,2.104 4.156,3.01 4.156,3.01 4.333,3.01 false 3.844,1.854 4.229,1 4.229,1 4.406,1 false 3.385,0.542 3.844,0.771 0.458,0.229 10 false G100 4.615,2.24 5.219,2.438 0.604,0.198 10 false CANL*a 2.333,1 2.969,1.208 0.635,0.208 10 false CANH*f 4.719,1.635 5.323,1.823 0.604,0.188 10 false CANH*a 2.51,2.531 3.125,2.729 0.615,0.198 10 false CANL*f 4.438,0.927 5.083,1.135 0.646,0.208 10 false CANH*d 2.49,0.802 3.094,1.031 0.604,0.229 10 false CANH*e 4.365,2.938 5.021,3.156 0.656,0.219 10 false CANL*d 2.698,2.75 3.281,2.969 0.583,0.219 10 false CANL*e 4.51,2.677 5.083,2.844 0.573,0.167 10 false CANL*c 4.531,1.188 5.177,1.365 0.646,0.177 10 false CANH*c 4.635,1.417 5.281,1.594 0.646,0.177 10 false CANH*b 4.552,2.458 5.146,2.646 0.594,0.188 10 false CANL*b

Text in Illustration
*a for No. 1 Junction Connector *b
·

for Navigation Receiver Assembly (w/ Navigation System [for Navigation Receiver Type])

·

for Radio and Display Receiver Assembly (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)


*c for Spiral Cable Sub-assembly (Steering Angle Sensor) *d for Yaw Rate Sensor Assembly
*e for Center Airbag Sensor Assembly *f for No. 3 Junction Connector (V1 Bus)

No. 2 Junction Connector Wiring Color Connect to
G100-1 (CANH) GR No. 1 junction connector
G100-12 (CANL) W
G100-2 (CANH) P
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


G100-13 (CANL) W
G100-3 (CANH) G Spiral cable sub-assembly (steering angle sensor)
G100-14 (CANL) W
G100-4 (CANH) R Yaw rate sensor assembly
G100-15 (CANL) W
G100-5 (CANH) Y Center airbag sensor assembly
G100-16 (CANL) W
G100-6 (CANH) LG No. 3 junction connector (V1 Bus)
G100-17 (CANL) W

*1: w/ Navigation System (for Navigation Receiver Type)

*2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System



c.

No. 3 Junction Connector

i.

G94 No. 3 junction connector

U170136E02
3.573,1.854 3.115,0.99 3.115,0.99 2.979,0.99 false 4.208,1.854 4.563,1.698 4.563,1.698 4.677,1.698 false 4.604,1.49 4.469,1.49 4.469,1.49 4.083,1.854 false 3.958,1.854 4.354,1.26 4.354,1.26 4.49,1.26 false 3.573,2.104 3.229,2.604 3.229,2.604 3.083,2.604 false 4.208,2.104 4.479,2.313 4.479,2.313 4.583,2.313 false 4.531,2.521 4.396,2.521 4.396,2.521 4.094,2.104 false 3.979,2.104 4.333,2.75 4.333,2.75 4.469,2.75 false 3.719,2.104 4.156,3.01 4.156,3.01 4.333,3.01 false 3.708,1.854 4.229,1 4.229,1 4.406,1 false 3.469,0.542 3.75,0.688 0.281,0.146 10 false G94 4.604,2.24 5.188,2.427 0.583,0.188 10 false CANL*a 4.688,1.635 5.271,1.813 0.583,0.177 10 false CANH*a 4.427,0.927 5.042,1.104 0.615,0.177 10 false CANH*d 2.385,0.906 2.99,1.135 0.604,0.229 10 false CANH*e 4.354,2.938 5,3.177 0.646,0.24 10 false CANL*d 2.542,2.531 3.167,2.74 0.625,0.208 10 false CANL*e 4.5,2.677 5.146,2.885 0.646,0.208 10 false CANL*c 4.531,1.188 5.156,1.385 0.625,0.198 10 false CANH*c 4.635,1.417 5.26,1.594 0.625,0.177 10 false CANH*b 4.552,2.458 5.125,2.625 0.573,0.167 10 false CANL*b

Text in Illustration
*a for No. 2 Junction Connector *b for Combination Meter Assembly (for 2TR-FE)
*c for Main Body ECU (Multiplex Network Body ECU) (V1 Bus) *d for DLC3
*e for No. 5 Junction Connector (for 1GR-FE, 1KD-FTV, 1GD-FTV) - -

No. 3 Junction Connector Wiring Color Connect to
G94-1 (CANH) LG No. 2 junction connector
G94-12 (CANL) W
G94-2 (CANH) V Combination meter assembly*1
G94-13 (CANL) W
G94-3 (CANH) L Main body ECU (multiplex network body ECU) (V1 Bus)
G94-14 (CANL) W
G94-5 (CANH) R DLC3
G94-16 (CANL) W
G94-6 (CANH) B No. 5 junction connector*2
G94-17 (CANL) W

*1: for 2TR-FE

*2: for 1GR-FE, 1KD-FTV, 1GD-FTV



ii.

G95 No. 3 junction connector

U170137E02
3.573,1.854 3.115,0.99 3.115,0.99 2.979,0.99 false 4.208,1.854 4.563,1.698 4.563,1.698 4.677,1.698 false 3.969,1.854 4.365,1.365 4.365,1.365 4.5,1.365 false 3.573,2.104 3.229,2.604 3.229,2.604 3.083,2.604 false 4.208,2.104 4.479,2.313 4.479,2.313 4.583,2.313 false 3.979,2.104 4.344,2.635 4.344,2.635 4.479,2.635 false 3.719,2.104 4.167,2.906 4.167,2.906 4.344,2.906 false 3.708,1.854 4.229,1 4.229,1 4.406,1 false 3.469,0.542 3.75,0.688 0.281,0.146 10 false G95 4.604,2.24 5.188,2.438 0.583,0.198 10 false CANL*a 4.698,1.625 5.333,1.823 0.635,0.198 10 false CANH*a 4.438,0.927 5.073,1.146 0.635,0.219 10 false CANH*c 2.385,0.906 2.969,1.083 0.583,0.177 10 false CANH*d 4.365,2.833 4.927,3.021 0.563,0.188 10 false CANL*c 2.542,2.531 3.167,2.75 0.625,0.219 10 false CANL*d 4.51,2.563 5.135,2.771 0.625,0.208 10 false CANL*b 4.531,1.292 5.177,1.49 0.646,0.198 10 false CANH*b

Text in Illustration
*a for No. 1 Junction Connector (V2 Bus) *b
·

for No. 6 Junction Connector (w/ Blind Spot Monitor System)

·

for No. 5 Junction Connector (w/o Blind Spot Monitor System) (V2 Bus)


*c for Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System) *d for Seat Belt Control ECU (w/ Pre-crash Safety System)

No. 3 Junction Connector Wiring Color Connect to
G95-1 (CANH) P No. 1 junction connector (V2 Bus)
G95-12 (CANL) W
G95-3 (CANH) LG
·

No. 6 junction connector*1

·

No. 5 junction connector*2 (V2 Bus)


G95-14 (CANL) W
G95-5 (CANH) V Stabilizer control ECU*3
G95-16 (CANL) W
G95-6 (CANH) L Seat belt control ECU*4
G95-17 (CANL) W

*1: w/ Blind Spot Monitor System

*2: w/o Blind Spot Monitor System

*3: w/ Kinetic Dynamic Suspension System

*4: w/ Pre-crash Safety System



iii.

G96 No. 3 junction connector

U148558E02
3.573,1.854 3.073,0.885 3.073,0.885 2.938,0.885 false 4.083,1.854 4.427,1.698 4.427,1.698 4.542,1.698 false 4.479,1.49 4.354,1.49 4.354,1.49 3.958,1.854 false 3.854,1.854 4.24,1.26 4.24,1.26 4.375,1.26 false 3.594,2.104 3.26,2.823 3.26,2.823 3.125,2.823 false 4.094,2.104 4.354,2.313 4.354,2.313 4.469,2.313 false 4.406,2.521 4.271,2.521 4.271,2.521 3.969,2.104 false 3.865,2.104 4.208,2.75 4.208,2.75 4.344,2.75 false 3.74,2.104 4.031,3.01 4.031,3.01 4.208,3.01 false 3.719,1.854 4.094,1 4.094,1 4.271,1 false 3.479,0.542 3.76,0.688 0.281,0.146 10 false G96 4.5,2.24 5.104,2.438 0.604,0.198 10 false CANL*a 4.583,1.635 5.177,1.813 0.594,0.177 10 false CANH*a 4.313,0.927 4.927,1.115 0.615,0.188 10 false CANH*d 2.375,0.813 2.958,1.01 0.583,0.198 10 false CANH*e 4.229,2.938 4.854,3.115 0.625,0.177 10 false CANL*d 2.573,2.75 3.219,2.938 0.646,0.188 10 false CANL*e 4.375,2.677 5.01,2.875 0.635,0.198 10 false CANL*c 4.406,1.188 5.052,1.375 0.646,0.188 10 false CANH*c 4.521,1.417 5.146,1.604 0.625,0.188 10 false CANH*b 4.438,2.458 5.063,2.625 0.625,0.167 10 false CANL*b

Text in Illustration
*a for Front Power Seat Switch LH (w/ Seat Position Memory) *b for Multiplex Tilt and Telescopic ECU (for Power Tilt and Power Telescopic Steering Column)
*c for Main Body ECU (Multiplex Network Body ECU) (MS Bus) *d for Driving Support Switch Control ECU (w/ Multi-function Switch)
*e for No. 8 Junction Connector - -

No. 3 Junction Connector Wiring Color Connect to
G96-2 (CANH) L Front power seat switch LH*1
G96-13 (CANL) W
G96-3 (CANH) GR Multiplex tilt and telescopic ECU*2
G96-14 (CANL) W
G96-4 (CANH) P Main body ECU (multiplex network body ECU) (MS Bus)
G96-15 (CANL) W
G96-5 (CANH) R Driving support switch control ECU*3
G96-16 (CANL) W
G96-6 (CANH) LG No. 8 junction connector
G96-17 (CANL) W

*1: w/ Seat Position Memory

*2: for Power Tilt and Power Telescopic Steering Column

*3: w/ Multi-function Switch




d.

No. 4 Junction Connector (for 2TR-FE)

U170127E02
2.979,2.104 2.76,2.313 2.76,2.313 2.646,2.313 false 3.229,2.104 2.729,2.823 2.729,2.823 2.615,2.823 false 3.094,2.104 2.677,2.583 2.677,2.583 2.563,2.583 false 2.958,1.865 2.74,1.656 2.74,1.656 2.625,1.656 false 3.219,1.865 2.719,1.146 2.719,1.146 2.604,1.146 false 3.083,1.865 2.667,1.375 2.667,1.375 2.552,1.375 false 2.063,2.76 2.677,3.01 0.615,0.25 10 false CANL*a 2.094,2.229 2.719,2.458 0.625,0.229 10 false CANL*c 2.021,2.51 2.625,2.688 0.604,0.177 10 false CANL*b 3.469,0.688 3.823,0.875 0.354,0.188 10 false A72 2.021,1.052 2.667,1.25 0.646,0.198 10 false CANH*a 2,1.281 2.594,1.49 0.594,0.208 10 false CANH*b 2.073,1.573 2.688,1.792 0.615,0.219 10 false CANH*c

Text in Illustration
*a for No. 1 Junction Connector (V1 Bus) *b for ECM (V1 Bus)
*c for Brake Actuator Assembly (Skid Control ECU) - -

No. 4 Junction Connector Wiring Color Connect to
A72-9 (CANH) R No. 1 junction connector (V1 Bus)
A72-20 (CANL) W
A72-10 (CANH) LG ECM (V1 Bus)
A72-21 (CANL) W
A72-11 (CANH) B Brake actuator assembly (skid control ECU)
A72-22 (CANL) W


e.

No. 5 Junction Connector

U148559E02
2.958,1.854 2.573,1.448 2.573,1.448 2.458,1.448 false 2.531,1.219 2.656,1.219 2.656,1.219 3.083,1.854 false 3.219,1.854 2.854,1.01 2.854,1.01 2.719,1.01 false 4.198,1.854 4.406,1.698 4.406,1.698 4.521,1.698 false 4.51,1.521 4.375,1.521 4.375,1.521 4.083,1.854 false 2.969,2.104 2.75,2.448 2.75,2.448 2.646,2.448 false 2.771,2.656 2.896,2.656 2.896,2.656 3.104,2.104 false 3.229,2.104 3.115,2.875 3.115,2.875 2.979,2.875 false 4.208,2.104 4.417,2.344 4.417,2.344 4.531,2.344 false 4.479,2.552 4.344,2.552 4.344,2.552 4.094,2.104 false 3.979,2.104 4.26,2.76 4.26,2.76 4.438,2.76 false 3.969,1.854 4.333,1.313 4.333,1.313 4.51,1.313 false 3.833,1.854 4.198,1.094 4.198,1.094 4.375,1.094 false 3.844,2.104 4.083,3 4.083,3 4.26,3 false 3.469,0.542 3.823,0.76 0.354,0.219 10 false A73 4.552,2.271 5.135,2.479 0.583,0.208 10 false CANL*a 2.01,1.135 2.583,1.333 0.573,0.198 10 false CANH*f 4.552,1.635 5.156,1.833 0.604,0.198 10 false CANH*a 2.281,2.583 2.854,2.771 0.573,0.188 10 false CANL*f 2.167,0.917 2.781,1.094 0.615,0.177 10 false CANH*e 4.458,2.688 5.031,2.885 0.573,0.198 10 false CANL*c 2.448,2.802 3.073,2.979 0.625,0.177 10 false CANL*e 1.906,1.375 2.521,1.573 0.615,0.198 10 false CANH*g 2.125,2.354 2.75,2.563 0.625,0.208 10 false CANL*g 4.542,1.448 5.198,1.656 0.656,0.208 10 false CANH*b 4.5,2.49 5.083,2.646 0.583,0.156 10 false CANL*b 4.563,1.25 5.208,1.438 0.646,0.188 10 false CANH*c 4.427,1.021 5.042,1.229 0.615,0.208 10 false CANH*d 4.302,2.948 4.917,3.167 0.615,0.219 10 false CANL*d

Text in Illustration
*a for No. 7 Junction Connector *b
·

for No. 6 Junction Connector (w/ Blind Spot Monitor System)

·

for No. 3 Junction Connector (w/o Blind Spot Monitor System) (V2 Bus)


*c for Suspension Control ECU (w/ Air Suspension System) *d for Headlight Swivel ECU Assembly (for LED Headlight)
*e for No. 3 Junction Connector (V1 Bus) *f for Combination Meter Assembly (for 1GR-FE, 1KD-FTV, 1GD-FTV)
*g for Master Cylinder Solenoid (Skid Control ECU) (for 1GR-FE, 1KD-FTV, 1GD-FTV) - -

No. 5 Junction Connector Wiring Color Connect to
A73-1 (CANH) LG No. 7 junction connector
A73-12 (CANL) W
A73-2 (CANH) B
·

No. 6 junction connector*1

·

No. 3 junction connector*2 (V2 bus)


A73-13 (CANL) W
A73-3 (CANH) GR Suspension control ECU*3
A73-14 (CANL) W
A73-4 (CANH) V Headlight swivel ECU assembly*4
A73-15 (CANL) W
A73-9 (CANH) R No. 3 junction connector (V1 Bus)
A73-20 (CANL) W
A73-10 (CANH) LG Combination meter assembly*5
A73-21 (CANL) W
A73-11 (CANH) B Master cylinder solenoid (skid control ECU)*5
A73-22 (CANL) W

*1: w/ Blind Spot Monitor System

*2: w/o Blind Spot Monitor System

*3: w/ Air Suspension System

*4: for LED Headlight

*5: for 1GR-FE, 1KD-FTV, 1GD-FTV



f.

No. 6 Junction Connector (w/ Blind Spot Monitor System)

U148560E03
3.958,2.094 4.313,2.615 4.313,2.615 4.427,2.615 false 4.198,2.094 4.438,2.281 4.438,2.281 4.552,2.281 false 3.958,1.865 4.323,1.354 4.323,1.354 4.438,1.354 false 4.083,2.094 4.448,2.458 4.448,2.458 4.563,2.458 false 4.073,1.865 4.438,1.5 4.438,1.5 4.552,1.5 false 4.208,1.865 4.448,1.677 4.448,1.677 4.563,1.677 false 4.604,1.615 5.26,1.833 0.656,0.219 10 false CANH*a 4.594,2.208 5.24,2.438 0.646,0.229 10 false CANL*a 4.469,2.542 5.135,2.75 0.667,0.208 10 false CANL*c 4.604,2.385 5.271,2.615 0.667,0.229 10 false CANL*b 3.469,0.688 3.813,0.875 0.344,0.188 10 false R47 4.479,1.271 5.146,1.469 0.667,0.198 10 false CANH*c 4.594,1.427 5.26,1.688 0.667,0.26 10 false CANH*b

Text in Illustration
*a for No. 3 Junction Connector (V2 Bus) *b Blind Spot Monitor Sensor LH
*c for No. 5 Junction Connector (V2 Bus) - -

No. 6 Junction Connector Wiring Color Connect to
R47-1 (CANH) LG No. 3 junction connector (V2 bus)
R47-12 (CANL) W
R47-2 (CANH) G Blind spot monitor sensor LH
R47-13 (CANL) W
R47-3 (CANH) B No. 5 junction connector (V2 bus)
R47-14 (CANL) W


g.
U148309E03
2.219,0.24 2.156,0.24 2.156,0.24 1.385,0.865 false 2.479,1.594 2.417,1.594 2.417,1.594 1.729,1.073 false 2.26,0.167 2.99,0.375 0.729,0.208 10 false CANH*a 0.427,0.885 0.844,1.104 0.417,0.219 10 false G102 2.521,1.521 3.115,1.74 0.594,0.219 10 false CANL*a

No. 7 Junction Connector

Text in Illustration
*a for No. 5 Junction Connector (V2 Bus)

No. 7 Junction Connector Wiring Color Connect to
G102-2 (CANL) W No. 5 junction connector (V2 bus)
G102-3 (CANH) LG


h.
U148310E03
2.198,0.24 2.135,0.24 2.135,0.24 1.365,0.865 false 2.469,1.594 2.406,1.594 2.406,1.594 1.719,1.073 false 2.26,0.167 2.979,0.396 0.719,0.229 10 false CANP*a 0.438,0.896 0.865,1.135 0.427,0.24 10 false G103 2.521,1.521 3.135,1.792 0.615,0.271 10 false CANN*a

No. 8 Junction Connector (w/ Multi-function Switch)

Text in Illustration
*a for No. 3 Junction Connector (MS Bus)

No. 8 Junction Connector Wiring Color Connect to
G103-2 (CANN) W No. 3 junction connector (MS bus)
G103-3 (CANP) LG


i.

No. 9 Junction Connector (w/ Urea SCR System)

U170476E03
4.552,1.281 4.479,1.281 4.479,1.281 3.833,1.854 false 3.833,2.094 4.5,2.635 4.5,2.635 4.583,2.635 false 4.552,0.948 4.479,0.948 4.479,0.948 3.708,1.854 false 3.708,2.083 4.49,3.083 4.49,3.083 4.573,3.083 false 3.583,2.083 4.479,3.458 4.479,3.458 4.583,3.458 false 3.583,1.854 4.479,0.531 4.479,0.531 4.552,0.531 false 3.469,0.479 3.865,0.719 0.396,0.24 10 false Q41 4.635,2.552 5.24,2.729 0.604,0.177 10 false CANL*a 4.615,3.01 5.177,3.188 0.563,0.177 10 false CANL*b 4.583,0.865 5.146,1.042 0.563,0.177 10 false CANH*b 4.594,1.208 5.167,1.385 0.573,0.177 10 false CANH*a 4.594,0.448 5.156,0.625 0.563,0.177 10 false CANH*c 4.646,3.385 5.208,3.552 0.563,0.167 10 false CANL*c

Text in Illustration
*a for Urea Pump Control ECU *b for ECM
*c for Nitrogen Oxides Sensor - -

No. 9 Junction Connector Wiring Color Connect to
Q41-4 (CANH) W Urea pump control ECU
Q41-15 (CANL) B
Q41-5 (CANH) L ECM
Q41-16 (CANL) W
Q41-6 (CANH) L Nitrogen oxides sensor
Q41-17 (CANL) W



CHECK DLC3


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.
U149545E02
1.969,0.917 2.073,0.49 2.073,0.49 2.146,0.49 false 1.604,0.896 1.344,0.469 1.344,0.469 1.281,0.469 false 1.948,1.469 1.802,1.844 1.802,1.844 1.74,1.844 false 2.333,1.448 2.396,1.813 2.396,1.813 2.448,1.813 false 0.229,1.167 0.51,1.344 0.281,0.177 10 false G48 2.229,0.396 2.677,0.573 0.448,0.177 10 false CANH 1.021,0.385 1.26,0.542 0.24,0.156 10 false CG 2.5,1.729 2.813,1.906 0.313,0.177 10 false BAT 1.302,1.75 1.688,1.927 0.385,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) R - W Engine switch off 54 to 69 Ω
G48-6 (CANH) - G48-4 (CG) R - W-B Engine switch off 200 Ω or higher
G48-14 (CANL) - G48-4 (CG) W - W-B Engine switch off 200 Ω or higher
G48-6 (CANH) - G48-16 (BAT) R - GR Engine switch off 6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK ECM (for 1GR-FE)


U170145E02
0.99,1.677 0.698,2.073 0.698,2.073 0.604,2.073 true 2.031,1.688 1.844,2 1.844,2 1.75,2 true 2.208,1.688 2.042,2.229 2.042,2.229 1.948,2.229 true 2.427,1.688 2.625,2 2.625,2 2.719,2 true 2.302,1.688 2.458,2.229 2.458,2.229 2.552,2.229 true 2.438,1.552 2.625,0.604 2.625,0.604 2.719,0.604 true 5.219,1.323 5.677,0.573 5.677,0.573 5.771,0.573 true 0.229,2.021 0.688,2.208 0.458,0.188 10 false BATT 4.833,0.49 5.177,0.677 0.344,0.188 10 false C36 2.052,0.49 2.375,0.688 0.323,0.198 10 false G56 1.125,0.49 1.469,0.656 0.344,0.167 10 false G55 2.74,1.948 4.281,2.177 1.542,0.229 10 false CANL*A, CANH*C 2.583,2.177 3.5,2.396 0.917,0.219 10 false CANH*A 1.188,1.927 2.042,2.115 0.854,0.188 10 false CANP*B 1.396,2.167 2.281,2.385 0.885,0.219 10 false CANN*B 2.74,0.552 3.688,0.771 0.948,0.219 10 false CANL*C 5.802,0.49 6.083,0.719 0.281,0.229 10 false E1

Text in Illustration
*A for V1 Bus (for Manual Transmission System) *B for Power Management Bus
*C for V1 Bus (for Automatic Transmission System) - -

a.

Disconnect the C36, G55 and G56 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus (for Manual Transmission System)
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G56-32 (CANH) - G56-31 (CANL) R - W Engine switch off 108 to 132 Ω
G56-32 (CANH) - C36-12 (E1) R - BR Engine switch off 200 Ω or higher
G56-31 (CANL) - C36-12 (E1) W - BR Engine switch off 200 Ω or higher
G56-32 (CANH) - G55-24 (BATT) R - L Engine switch off 6 kΩ or higher
G56-31 (CANL) - G55-24 (BATT) W - L Engine switch off 6 kΩ or higher

for V1 Bus (for Automatic Transmission System)
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) R - W Engine switch off 108 to 132 Ω
G56-31 (CANH) - C36-12 (E1) R - BR Engine switch off 200 Ω or higher
G56-25 (CANL) - C36-12 (E1) W - BR Engine switch off 200 Ω or higher
G56-31 (CANH) - G55-24 (BATT) R - L Engine switch off 6 kΩ or higher
G56-25 (CANL) - G55-24 (BATT) W - L Engine switch off 6 kΩ or higher

for Power Management Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G56-34 (CANP) - G56-33 (CANN) BR - GR Engine switch off 108 to 132 Ω
G56-34 (CANP) - C36-12 (E1) BR - BR Engine switch off 200 Ω or higher
G56-33 (CANN) - C36-12 (E1) GR - BR Engine switch off 200 Ω or higher
G56-34 (CANP) - G55-24 (BATT) BR - L Engine switch off 6 kΩ or higher
G56-33 (CANN) - G55-24 (BATT) GR - L Engine switch off 6 kΩ or higher



CHECK ECM (for 1KD-FTV)


U170143E03
1.198,1.688 0.896,2.083 0.896,2.083 0.813,2.083 true 1.646,1.688 1.917,2.427 1.917,2.427 2.01,2.427 true 1.552,1.677 1.677,2.656 1.677,2.656 1.771,2.656 true 1.948,1.677 2.146,1.99 2.146,1.99 2.229,1.99 true 1.875,1.688 2.031,2.229 2.031,2.229 2.125,2.229 true 5.031,1.49 4.729,2.031 4.729,2.031 4.635,2.031 true 5.052,1.583 5.24,2.021 5.24,2.021 5.333,2.021 true 6.25,1.177 6.563,0.823 6.563,0.823 6.656,0.823 true 0.458,2.031 0.865,2.281 0.406,0.25 10 false BATT 5.729,0.49 6.042,0.698 0.313,0.208 10 false C93 4.781,0.49 5.073,0.729 0.292,0.24 10 false C92 2.042,0.49 2.375,0.667 0.333,0.177 10 false G58 1.125,0.49 1.427,0.688 0.302,0.198 10 false G57 2.052,2.354 2.906,2.542 0.854,0.188 10 false CANP*B 1.802,2.594 2.76,2.75 0.958,0.156 10 false CANN*B 2.26,1.917 3.083,2.083 0.823,0.167 10 false CANH*A 2.156,2.156 3.031,2.375 0.875,0.219 10 false CANL*A 4.094,1.958 4.906,2.156 0.813,0.198 10 false CAN-*C 5.365,1.948 6.188,2.135 0.823,0.188 10 false CAN+*C 6.688,0.75 6.958,0.948 0.271,0.198 10 false E1

Text in Illustration
*A for V1 Bus *B for Power Management Bus
*C for Powertrain Bus - -

a.

Disconnect the C92, C93, G57 and G58 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) R - W Engine switch off 108 to 132 Ω
G58-35 (CANH) - C93-1 (E1) R - BR Engine switch off 200 Ω or higher
G58-36 (CANL) - C93-1 (E1) W - BR Engine switch off 200 Ω or higher
G58-35 (CANH) - G57-23 (BATT) R - L Engine switch off 6 kΩ or higher
G58-36 (CANL) - G57-23 (BATT) W - L Engine switch off 6 kΩ or higher

for Power Management Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G57-20 (CANP) - G57-21 (CANN) BR - GR Engine switch off 108 to 132 Ω
G57-20 (CANP) - C93-1 (E1) BR - BR Engine switch off 200 Ω or higher
G57-21 (CANN) - C93-1 (E1) GR - BR Engine switch off 200 Ω or higher
G57-20 (CANP) - G57-23 (BATT) BR - L Engine switch off 6 kΩ or higher
G57-21 (CANN) - G57-23 (BATT) GR - L Engine switch off 6 kΩ or higher

for Powertrain Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
C92-24 (CAN+) - C92-18 (CAN-) B - W Engine switch off 108 to 132 Ω
C92-24 (CAN+) - C93-1 (E1) B - BR Engine switch off 200 Ω or higher
C92-18 (CAN-) - C93-1 (E1) W - BR Engine switch off 200 Ω or higher
C92-24 (CAN+) - G57-23 (BATT) B - L Engine switch off 6 kΩ or higher
C92-18 (CAN-) - G57-23 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK ECM (for 2TR-FE)


U170486E02
4.708,1.24 4.396,0.281 4.396,0.281 4.313,0.281 true 4.604,1.25 4.135,0.625 4.135,0.625 4.042,0.625 true 1.042,1.104 1.292,0.552 1.292,0.552 1.385,0.552 true 6.448,1.104 6.573,0.583 6.573,0.583 6.667,0.583 true 6.708,0.51 7.104,0.677 0.396,0.167 10 false BATT 0.74,0.292 1.156,0.469 0.417,0.177 10 false C153 6.083,0.281 6.5,0.49 0.417,0.208 10 false G180 4.792,0.281 5.271,0.5 0.479,0.219 10 false G181 3.677,0.552 4.146,0.719 0.469,0.167 10 false CANL 3.906,0.208 4.385,0.375 0.479,0.167 10 false CANH 1.438,0.479 1.667,0.646 0.229,0.167 10 false E1

a.

Disconnect the C153, G180 and G181 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G181-13 (CANH) - G181-14 (CANL) LG - W Engine switch off 108 to 132 Ω
G181-13 (CANH) - C153-3 (E1) LG - BR Engine switch off 200 Ω or higher
G181-14 (CANL) - C153-3 (E1) W - BR Engine switch off 200 Ω or higher
G181-13 (CANH) - G180-3 (BATT) LG - L Engine switch off 6 kΩ or higher
G181-14 (CANL) - G180-3 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK ECM (for 1GD-FTV)


U170469E03
6.688,1.792 6.75,1.792 6.75,1.792 6.875,1.073 false 4.021,1.781 4.083,1.781 4.083,1.781 4.604,1.063 true 5.813,1.313 6.073,2.115 6.073,2.115 6.156,2.115 true 5.802,1.438 5.917,2.438 5.917,2.438 5.99,2.438 true 4.385,2.458 4.438,2.458 4.438,2.458 4.771,1.448 true 4.208,2.135 4.26,2.135 4.26,2.135 4.771,1.323 true 0.615,0.375 1.01,0.552 0.396,0.177 10 false C149 1.75,0.375 2.115,0.552 0.365,0.177 10 false C150 2.979,0.385 3.354,0.563 0.375,0.177 10 false C151 4.042,0.375 4.427,0.552 0.385,0.177 10 false C152 5.135,0.375 5.51,0.552 0.375,0.177 10 false G184 6.24,0.375 6.615,0.552 0.375,0.177 10 false G185 6.042,2.365 6.646,2.542 0.604,0.177 10 false CANL*A 3.646,2.052 4.208,2.229 0.563,0.177 10 false CANU*B 3.823,2.385 4.385,2.563 0.563,0.177 10 false CAND*B 6.313,1.708 6.729,1.885 0.417,0.177 10 false BATT 6.208,2.042 6.771,2.219 0.563,0.177 10 false CANH*A 3.813,1.698 4.063,1.865 0.25,0.167 10 false E1

Text in Illustration
*A for V1 Bus *B for Local Bus

a.

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G184-17 (CANH) - G184-28 (CANL) R - W Engine switch off 108 to 132 Ω
G184-17 (CANH) - C152-1 (E1) R - W-B Engine switch off 200 Ω or higher
G184-28 (CANL) - C152-1 (E1) W - W-B Engine switch off 200 Ω or higher
G184-17 (CANH) - G185-1 (BATT) R - L Engine switch off 6 kΩ or higher
G184-28 (CANL) - G185-1 (BATT) W - L Engine switch off 6 kΩ or higher

for Local Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) L - W Engine switch off 108 to 132 Ω
G184-27 (CANU) - C152-1 (E1) L - W-B Engine switch off 200 Ω or higher
G184-35 (CAND) - C152-1 (E1) W - W-B Engine switch off 200 Ω or higher
G184-27 (CANU) - G185-1 (BATT) L - L Engine switch off 6 kΩ or higher
G184-35 (CAND) - G185-1 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U169735E02
1.625,1.531 1.823,1.292 1.823,1.292 1.906,1.292 false 1.625,1.854 1.823,1.698 1.823,1.698 1.906,1.698 false 1.625,2.188 1.823,2.385 1.823,2.385 1.906,2.385 false 5.031,8.135 5.281,7.708 5.281,7.708 5.385,7.708 true 3.031,8.135 2.781,7.708 2.781,7.708 2.677,7.708 true 3.573,4.604 3.427,5.156 3.427,5.156 3.344,5.156 true 3.49,4.604 3.344,4.979 3.344,4.979 3.26,4.979 true 1.354,4.604 1.5,5.156 1.5,5.156 1.583,5.156 true 1.438,4.604 1.594,4.969 1.594,4.969 1.677,4.969 true 1.615,1.031 1.615,0.615 1.615,0.615 1.76,0.615 false 0.896,1.635 1.104,1.792 0.208,0.156 10 false 2I 3.594,3.896 3.875,4.052 0.281,0.156 10 false G64 0.896,2.229 1.104,2.385 0.208,0.156 10 false 2F 5.865,1.552 6.073,1.708 0.208,0.156 10 false 2D 5.865,2.26 6.073,2.417 0.208,0.156 10 false 2A 1.073,2.771 1.281,2.927 0.208,0.156 10 false 2K 3.75,1.354 3.865,1.5 0.115,0.146 10 false A 1.927,1.219 2.302,1.365 0.375,0.146 10 false G65 1.792,0.552 2.167,0.698 0.375,0.146 10 false *1 1.927,2.313 2.271,2.458 0.344,0.146 10 false G63 1.927,1.646 2.323,1.792 0.396,0.146 10 false G64 1.094,3.896 1.375,4.052 0.281,0.156 10 false G63 1.125,5.198 1.344,5.354 0.219,0.156 10 false 2I 1.885,6.438 2.104,6.594 0.219,0.156 10 false 2D 4.938,6.438 5.156,6.594 0.219,0.156 10 false 2A 3.51,7.677 3.646,7.833 0.135,0.156 10 false A 3.948,5.208 4.146,5.365 0.198,0.156 10 false 2F 5.896,5.208 6.094,5.365 0.198,0.156 10 false 2K 5.906,3.896 6.188,4.052 0.281,0.156 10 false G65 5.417,7.646 5.833,7.802 0.417,0.156 10 false BECU 2.281,7.646 2.698,7.802 0.417,0.156 10 false GND1 2.823,5.083 3.375,5.24 0.552,0.156 10 false CANL*A 2.708,4.906 3.302,5.063 0.594,0.156 10 false CANH*A 1.719,4.896 2.302,5.052 0.583,0.156 10 false CANP*B 1.625,5.083 2.24,5.24 0.615,0.156 10 false CANN*B

Text in Illustration
*A for V1 Bus *B for MS Bus
*1 Main Body ECU (Multiplex Network Body ECU) - -

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) L - W Engine switch off 54 to 69 Ω
G64-14 (CANH) - A-11 (GND1) L - None Engine switch off 200 Ω or higher
G64-13 (CANL) - A-11 (GND1) W - None Engine switch off 200 Ω or higher
G64-14 (CANH) - A-30 (BECU) L - None Engine switch off 6 kΩ or higher
G64-13 (CANL) - A-30 (BECU) W - None Engine switch off 6 kΩ or higher

for MS Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G63-9 (CANP) - G63-10 (CANN) P - W Engine switch off 108 to 132 Ω
G63-9 (CANP) - A-11 (GND1) P - None Engine switch off 200 Ω or higher
G63-10 (CANN) - A-11 (GND1) W - None Engine switch off 200 Ω or higher
G63-9 (CANP) - A-30 (BECU) P - None Engine switch off 6 kΩ or higher
G63-10 (CANN) - A-30 (BECU) W - None Engine switch off 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


U149211E04
4.719,1.146 4.927,0.927 4.927,0.927 5.01,0.927 true 4.115,1.156 4.24,0.365 4.24,0.365 4.323,0.365 true 2.448,1.198 2.188,1.385 2.188,1.385 2.063,1.385 true 2.552,1.198 2.323,1.625 2.323,1.625 2.198,1.625 true 3.49,0.333 3.76,0.5 0.271,0.167 10 false G6 5.094,0.865 5.354,1.052 0.26,0.188 10 false E2 4.396,0.292 4.531,0.479 0.135,0.188 10 false B 1.656,1.302 2.115,1.51 0.458,0.208 10 false CANH 1.813,1.542 2.344,1.771 0.531,0.229 10 false CANL

a.

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) LG - W*1
V - W*2
Engine switch off 108 to 132 Ω
G6-40 (CANH) - G6-21 (E2) LG - BR*1
V - BR*2
Engine switch off 200 Ω or higher
G6-39 (CANL) - G6-21 (E2) W - BR Engine switch off 200 Ω or higher
G6-40 (CANH) - G6-26 (B) LG - L*1
V - L*2
Engine switch off 6 kΩ or higher
G6-39 (CANL) - G6-26 (B) W - L Engine switch off 6 kΩ or higher

*1: for 1GR-FE, 1KD-FTV, 1GD-FTV

*2: for 2TR-FE




CHECK POWER STEERING ECU ASSEMBLY


U148691E04
2.135,1.094 2.354,0.5 2.354,0.5 2.479,0.5 true 2.281,1.115 2.635,0.74 2.635,0.74 2.74,0.74 true 5.771,1.271 5.979,1.396 5.979,1.396 6.083,1.396 true 1.76,0.49 1.844,0.49 1.844,0.49 1.969,1.083 true 0.438,0.938 0.792,1.125 0.354,0.188 10 false G46 2.792,0.667 3.229,0.896 0.438,0.229 10 false CANH 2.521,0.427 2.927,0.656 0.406,0.229 10 false CANL 1.427,0.406 1.771,0.594 0.344,0.188 10 false GND 6.135,1.323 6.542,1.552 0.406,0.229 10 false BAT 4,1 4.354,1.188 0.354,0.188 10 false G48

a.

Disconnect the G46 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) L - W Engine switch off 54 to 69 Ω
G46-1 (CANH) - G46-3 (GND) L - W-B Engine switch off 200 Ω or higher
G46-2 (CANL) - G46-3 (GND) W - W-B Engine switch off 200 Ω or higher
G46-1 (CANH) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
G46-2 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


C215955E08
5.615,0.406 6.094,0.688 0.479,0.281 1.823,0.406 2.302,0.688 0.479,0.281 3.802,0.344 4.281,0.625 0.479,0.281 3.635,1.135 3.448,0.677 3.448,0.677 3.354,0.677 true 3.885,1.135 3.698,0.417 3.698,0.417 3.604,0.417 true 4.021,1.146 4.396,0.635 4.396,0.635 4.49,0.635 true 5.229,1.302 4.979,0.417 4.979,0.417 4.875,0.417 true 3.24,0.344 3.667,0.51 0.427,0.167 10 false CANL 4.521,0.563 4.948,0.729 0.427,0.167 10 false CANH 4.75,0.344 4.885,0.51 0.135,0.167 10 false B 3.042,0.604 3.417,0.771 0.375,0.167 10 false GND 5.781,0.469 6.01,0.635 0.229,0.167 10 false z1 1.917,0.469 2.208,0.635 0.292,0.167 10 false G24 3.906,0.396 4.198,0.563 0.292,0.167 10 false G25

a.

Disconnect the G25 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) BR - Y*1
BR - W*2
Engine switch off 54 to 69 Ω
G25-11 (CANH) - G25-14 (GND) BR - W-B Engine switch off 200 Ω or higher
G25-12 (CANL) - G25-14 (GND) Y - W-B*1
W - W-B*2
Engine switch off 200 Ω or higher
G25-11 (CANH) - G25-21 (B) BR - V Engine switch off 6 kΩ or higher
G25-12 (CANL) - G25-21 (B) Y - V*1
W - V*2
Engine switch off 6 kΩ or higher

*1: for 1KD-FTV, 1GR-FE and Manual Transmission System

*2: except 1KD-FTV, 1GR-FE and Manual Transmission System




CHECK CENTER AIRBAG SENSOR ASSEMBLY


U148296E01
1.332,0.448 1.613,0.660 0.281,0.212 10 G1 5.451,0.504 5.746,0.716 0.295,0.212 10 G48 2.157,0.654 2.600,0.800 0.443,0.147 10 CANH 2.191,2.133 2.634,2.279 0.443,0.147 10 CANL 1.837,1.377 2.076,0.727 2.076,0.727 2.127,0.727 false 1.079,2.119 1.271,2.265 0.193,0.147 10 E1 6.117,1.693 6.319,2.04 6.319,2.04 6.401,2.04 false 6.412,1.979 6.725,2.126 0.313,0.147 10 BAT 1.978,1.843 2.101,2.197 2.101,2.197 2.164,2.197 false 1.46,1.833 1.338,2.192 1.338,2.192 1.275,2.192 false

a.

Disconnect the G1 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Y - W Engine switch off 54 to 69 Ω
G1-13 (CANH) - G1-25 (E1) Y - W-B Engine switch off 200 Ω or higher
G1-22 (CANL) - G1-25 (E1) W - W-B Engine switch off 200 Ω or higher
G1-13 (CANH) - G48-16 (BAT) Y - GR Engine switch off 6 kΩ or higher
G1-22 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (for 1GR-FE, 1KD-FTV, 1GD-FTV)


U170045E03
2.146,0.677 2.313,0.219 2.313,0.219 2.406,0.219 true 2.156,0.969 2.417,1.635 2.417,1.635 2.51,1.635 true 3.927,0.688 3.75,0.229 3.75,0.229 3.646,0.229 true 4.24,0.698 4.417,0.302 4.417,0.302 4.521,0.302 true 2.542,1.563 2.969,1.729 0.427,0.167 10 false CANL 2.448,0.146 2.875,0.313 0.427,0.167 10 false CANH 3.26,0.146 3.656,0.313 0.396,0.167 10 false +BM1 4.563,0.229 5.01,0.396 0.448,0.167 10 false GND1 4.958,0.844 5.25,1.01 0.292,0.167 10 false A8 0.479,0.865 0.771,1.031 0.292,0.167 10 false A7

a.

Disconnect the A7 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) B - W Engine switch off 54 to 69 Ω
A7-11 (CANH) - A7-1 (GND1) B - W-B Engine switch off 200 Ω or higher
A7-25 (CANL) - A7-1 (GND1) W - W-B Engine switch off 200 Ω or higher
A7-11 (CANH) - A7-2 (+BM1) B - B Engine switch off 6 kΩ or higher
A7-25 (CANL) - A7-2 (+BM1) W - B Engine switch off 6 kΩ or higher



CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (for 2TR-FE)


U148729E03
4.438,0.646 4.896,0.354 4.896,0.354 5.042,0.354 true 4.167,1.281 4.5,1.594 4.5,1.594 4.604,1.594 true 4.156,1.021 4.938,0.583 4.938,0.583 5.031,0.583 true 2.698,1.167 2.354,1.49 2.354,1.49 2.25,1.49 true 1.375,0.771 1.646,0.948 0.271,0.177 10 false A6 5.094,0.281 5.542,0.458 0.448,0.177 10 false GND1 4.656,1.521 5.146,1.698 0.49,0.177 10 false CANH 5.083,0.521 5.573,0.698 0.49,0.177 10 false CANL 2.01,1.406 2.344,1.583 0.333,0.177 10 false BM

a.

Disconnect the A6 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) B - W Engine switch off 54 to 69 Ω
A6-25 (CANH) - A6-1 (GND1) B - W-B Engine switch off 200 Ω or higher
A6-14 (CANL) - A6-1 (GND1) W - W-B Engine switch off 200 Ω or higher
A6-25 (CANH) - A6-24 (BM) B - B Engine switch off 6 kΩ or higher
A6-14 (CANL) - A6-24 (BM) W - B Engine switch off 6 kΩ or higher



CHECK SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


U148274E04
2.25,1.188 2.583,0.594 2.583,0.594 2.667,0.594 true 1.969,1.188 1.635,0.594 1.635,0.594 1.542,0.594 true 2.344,1.177 2.677,0.813 2.677,0.813 2.76,0.813 true 2.156,1.188 2.354,0.396 2.354,0.396 2.448,0.396 true 2.719,0.5 3.146,0.667 0.427,0.167 10 false CANL 1.26,0.51 1.573,0.677 0.313,0.167 10 false BAT 2.865,1.094 3.177,1.26 0.313,0.167 10 false G33 2.813,0.74 3.125,0.917 0.313,0.177 10 false ESS 2.5,0.323 2.948,0.49 0.448,0.167 10 false CANH

a.

Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G33-4 (CANH) - G33-3 (CANL) G - W Engine switch off 54 to 69 Ω
G33-4 (CANH) - G33-2 (ESS) G - W-B Engine switch off 200 Ω or higher
G33-3 (CANL) - G33-2 (ESS) W - W-B Engine switch off 200 Ω or higher
G33-4 (CANH) - G33-6 (BAT) G - L Engine switch off 6 kΩ or higher
G33-3 (CANL) - G33-6 (BAT) W - L Engine switch off 6 kΩ or higher



CHECK YAW RATE SENSOR ASSEMBLY


U148362E02
2.313,0.865 2.417,1.677 2.417,1.677 2.531,1.677 true 2.229,0.875 1.969,1.573 1.969,1.573 1.875,1.573 true 2.417,0.865 2.896,1.563 2.896,1.563 2.99,1.563 true 5.635,1.333 5.844,1.656 5.844,1.656 5.948,1.656 true 2.052,0.323 2.344,0.469 0.292,0.146 10 false G52 4.979,0.323 5.271,0.469 0.292,0.146 10 false G48 2.573,1.583 2.99,1.771 0.417,0.188 10 false CANL 1.458,1.49 1.885,1.677 0.427,0.188 10 false CANH 3.031,1.49 3.365,1.667 0.333,0.177 10 false GND 6.01,1.573 6.302,1.75 0.292,0.177 10 false BAT

a.

Disconnect the G52 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G52-3 (CANH) - G52-2 (CANL) R - W Engine switch off 54 to 69 Ω
G52-3 (CANH) - G52-1 (GND) R - W-B Engine switch off 200 Ω or higher
G52-2 (CANL) - G52-1 (GND) W - W-B Engine switch off 200 Ω or higher
G52-3 (CANH) - G48-16 (BAT) R - GR Engine switch off 6 kΩ or higher
G52-2 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U169640E02
3.677,1.302 4.063,0.531 4.063,0.531 4.156,0.531 true 2.083,1.292 1.635,0.396 1.635,0.396 1.531,0.396 true 1.979,1.292 1.396,0.573 1.396,0.573 1.271,0.573 true 1.417,1.354 1,1.844 1,1.844 0.906,1.844 true 4.615,0.635 4.917,0.813 0.302,0.177 10 false G39 2.396,0.635 2.698,0.813 0.302,0.177 10 false G38 4.219,0.458 4.667,0.635 0.448,0.177 10 false +B 0.885,0.51 1.281,0.688 0.396,0.177 10 false CANL 1.115,0.313 1.552,0.49 0.438,0.177 10 false CANH 0.729,1.781 0.885,1.927 0.156,0.146 10 false E

a.

Disconnect the G38 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G38-9 (CANH) - G38-10 (CANL) P - W Engine switch off 54 to 69 Ω
G38-9 (CANH) - G38-15 (E) P - W-B Engine switch off 200 Ω or higher
G38-10 (CANL) - G38-15 (E) W - W-B Engine switch off 200 Ω or higher
G38-9 (CANH) - G38-1 (+B) P - V Engine switch off 6 kΩ or higher
G38-10 (CANL) - G38-1 (+B) W - V Engine switch off 6 kΩ or higher



CHECK POWER MANAGEMENT CONTROL ECU


U169943E02
4.104,1.688 3.99,2.281 3.99,2.281 3.917,2.281 true 4.063,2.479 4.156,2.479 4.156,2.479 4.188,1.688 true 4.844,1.406 5.052,1.052 5.052,1.052 5.146,1.052 true 3.698,1.406 3.51,1.063 3.51,1.063 3.417,1.063 true 4.104,1.563 3.917,0.875 3.917,0.875 3.844,0.875 true 4.052,0.708 4.146,0.708 4.146,0.708 4.188,1.552 true 4.448,1.563 4.625,0.875 4.625,0.875 4.698,0.875 true 4.49,0.708 4.406,0.708 4.406,0.708 4.365,1.552 true 5.219,1.469 5.521,1.656 0.302,0.188 10 false G51 5.167,0.969 5.573,1.125 0.406,0.156 10 false AM22 3.115,0.979 3.458,1.135 0.344,0.156 10 false GND 3.542,2.396 4.083,2.552 0.542,0.156 10 false CA2L*C 3.396,2.208 3.979,2.365 0.583,0.156 10 false CA2H*C 3.542,0.625 4.073,0.781 0.531,0.156 10 false CA1L*A 4.531,0.625 5.542,0.781 1.01,0.156 10 false CA3P*B, *C 3.333,0.802 3.865,0.958 0.531,0.156 10 false CA1H*A 4.74,0.802 5.76,0.958 1.021,0.156 10 false CA3N*B, *C

Text in Illustration
*A for V1 Bus *B for Power Management Bus
*C for V2 Bus - -

a.

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G51-14 (CA1H) - G51-13 (CA1L) BR - W Engine switch off 54 to 69 Ω
G51-14 (CA1H) - G51-6 (GND) BR - W-B Engine switch off 200 Ω or higher
G51-13 (CA1L) - G51-6 (GND) W - W-B Engine switch off 200 Ω or higher
G51-14 (CA1H) - G51-1 (AM22) BR - B Engine switch off 6 kΩ or higher
G51-13 (CA1L) - G51-1 (AM22) W - B Engine switch off 6 kΩ or higher

for V2 Bus (for 1KD-FTV, 1GR-FE and Manual Transmission System)
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) V - W Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) V - W-B Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) W - W-B Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) V - B Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) W - B Engine switch off 6 kΩ or higher

for V2 Bus (except 1KD-FTV, 1GR-FE and Manual Transmission System)
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) V - W Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) V - W-B Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) W - W-B Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) V - B Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) W - B Engine switch off 6 kΩ or higher

for Power Management Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) BR - W Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) BR - W-B Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) W - W-B Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) BR - B Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) W - B Engine switch off 6 kΩ or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System [for Navigation Receiver Type])


U170731E02
0.625,2.396 0.563,1.99 0.563,1.99 0.479,1.99 true 1.094,2.688 1.177,3.083 1.177,3.083 1.26,3.083 true 3.354,1.125 3.49,1.542 3.49,1.542 3.594,1.542 true 3.26,1.125 3.135,1.542 3.135,1.542 3.031,1.542 true 0.885,1.833 1.156,2.01 0.271,0.177 10 false H54 3.354,0.521 3.625,0.698 0.271,0.177 10 false H56 0.198,1.917 0.573,2.063 0.375,0.146 10 false +B1 1.313,3.01 1.75,3.156 0.438,0.146 10 false GND1 3.615,1.479 4.052,1.625 0.438,0.146 10 false CANH 2.625,1.479 3.063,1.625 0.438,0.146 10 false CANL

a.

Disconnect the H54 and H56 navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) W - P Engine switch off 54 to 69 Ω
H56-9 (CANH) - H54-7 (GND1) W - BR Engine switch off 200 Ω or higher
H56-10 (CANL) - H54-7 (GND1) P - BR Engine switch off 200 Ω or higher
H56-9 (CANH) - H54-4 (+B1) W - R Engine switch off 6 kΩ or higher
H56-10 (CANL) - H54-4 (+B1) P - R Engine switch off 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)


U170697E02
4.302,1.51 4.021,0.938 4.021,0.938 3.813,0.938 true 3.75,1.125 3.885,1.125 3.885,1.125 4.188,1.5 true 1.094,2.625 1.188,2.958 1.188,2.958 1.302,2.958 true 0.333,2.063 0.396,2.063 0.396,2.063 0.563,2.365 true 4.292,0.927 4.563,1.073 0.271,0.146 10 false H51 0.833,1.792 1.115,1.938 0.281,0.146 10 false H49 3.354,0.865 3.802,1.01 0.448,0.146 10 false CANH 3.354,1.052 3.802,1.198 0.448,0.146 10 false CANL 0.052,1.99 0.427,2.135 0.375,0.146 10 false +B1 1.333,2.896 1.781,3.042 0.448,0.146 10 false GND1

a.

Disconnect the H49 and H51 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) W - P Engine switch off 54 to 69 Ω
H51-9 (CANH) - H49-7 (GND1) W - BR Engine switch off 200 Ω or higher
H51-10 (CANL) - H49-7 (GND1) P - BR Engine switch off 200 Ω or higher
H51-9 (CANH) - H49-4 (+B1) W - R Engine switch off 6 kΩ or higher
H51-10 (CANL) - H49-4 (+B1) P - R Engine switch off 6 kΩ or higher



CHECK FOUR WHEEL DRIVE CONTROL ECU


U148363E04
0.906,0.813 0.854,0.354 0.854,0.354 0.771,0.354 true 0.823,0.813 0.688,0.542 0.688,0.542 0.604,0.542 true 2.5,0.802 2.375,0.448 2.375,0.448 2.292,0.448 true 5.792,1.115 5.917,1.354 5.917,1.354 6.01,1.354 true 1.979,0.365 2.313,0.552 0.333,0.188 10 false GND 2.677,0.354 2.99,0.563 0.313,0.208 10 false G54 0.344,0.271 0.76,0.458 0.417,0.188 10 false CANH 0.229,0.469 0.625,0.656 0.396,0.188 10 false CANL 1.427,0.354 1.781,0.531 0.354,0.177 10 false G53 4.031,0.875 4.344,1.083 0.313,0.208 10 false G48 6.052,1.281 6.344,1.469 0.292,0.188 10 false BAT

a.

Disconnect the G53 and G54 four wheel drive control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G53-19 (CANH) - G53-20 (CANL) G - W Engine switch off 54 to 69 Ω
G53-19 (CANH) - G54-4 (GND) G - W-B Engine switch off 200 Ω or higher
G53-20 (CANL) - G54-4 (GND) W - W-B Engine switch off 200 Ω or higher
G53-19 (CANH) - G48-16 (BAT) G - GR Engine switch off 6 kΩ or higher
G53-20 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK SUSPENSION CONTROL ECU (w/ Air Suspension System)


E346814E01
1.938,0.271 2.365,0.49 0.427,0.219 3.375,0.271 3.802,0.49 0.427,0.219 4.833,0.271 5.26,0.49 0.427,0.219 4.667,0.906 4.667,0.323 4.667,0.323 4.5,0.323 true 5.167,0.917 5.583,0.25 5.583,0.25 5.75,0.25 true 5.625,1.104 6.042,0.438 6.042,0.438 6.208,0.438 true 5.5,1.167 6,1.417 6,1.417 6.25,1.417 true 2.021,0.292 2.479,0.49 0.458,0.198 10 false R19 3.479,0.302 3.938,0.5 0.458,0.198 10 false A14 4.927,0.302 5.385,0.5 0.458,0.198 10 false A49 4.177,0.24 4.635,0.438 0.458,0.198 10 false GND 5.813,0.167 6.271,0.365 0.458,0.198 10 false B 6.26,0.344 6.719,0.542 0.458,0.198 10 false CANH 6.302,1.333 6.76,1.531 0.458,0.198 10 false CANL

a.

Disconnect the A49 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A49-7 (CANH) - A49-8 (CANL) GR - W Engine switch off 54 to 69 Ω
A49-7 (CANH) - A49-5 (GND) GR - W-B Engine switch off 200 Ω or higher
A49-8 (CANL) - A49-5 (GND) W - W-B Engine switch off 200 Ω or higher
A49-7 (CANH) - A49-3 (B) GR - GR Engine switch off 6 kΩ or higher
A49-8 (CANL) - A49-3 (B) W - GR Engine switch off 6 kΩ or higher



CHECK STABILIZER CONTROL ECU (w/ Kinetic Dynamic Suspension System)


U148404E02
6.281,1.094 6.479,1.448 6.479,1.448 6.563,1.448 true 1.813,1 2.01,1.458 2.01,1.458 2.094,1.458 true 1.729,1 1.854,1.635 1.854,1.635 1.938,1.635 true 2.344,0.948 2.552,0.49 2.552,0.49 2.635,0.49 true 2.083,0.146 2.458,0.313 0.375,0.167 10 false G123 5.615,0.146 5.906,0.354 0.292,0.208 10 false G48 6.573,1.385 6.885,1.531 0.313,0.146 10 false BAT 2.125,1.385 2.531,1.531 0.406,0.146 10 false CANL 1.969,1.573 2.396,1.719 0.427,0.146 10 false CANH 2.667,0.417 2.99,0.563 0.323,0.146 10 false GND

a.

Disconnect the G123 stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) V - W Engine switch off 54 to 69 Ω
G123-29 (CANH) - G123-22 (GND) V - W-B Engine switch off 200 Ω or higher
G123-28 (CANL) - G123-22 (GND) W - W-B Engine switch off 200 Ω or higher
G123-29 (CANH) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
G123-28 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK SEAT BELT CONTROL ECU (w/ Pre-crash Safety System)


U170572E02
4.771,1.688 5.156,0.344 5.156,0.344 5.323,0.344 true 4.896,1.698 5.521,0.771 5.521,0.771 5.688,0.771 true 3.146,1.646 2.479,0.438 2.479,0.438 2.313,0.438 true 2.833,1.667 2.01,0.698 2.01,0.698 1.844,0.698 true 4.531,0.583 4.938,0.729 0.406,0.146 10 false G118 2.823,0.583 3.198,0.729 0.375,0.146 10 false G117 5.75,0.698 6.208,0.844 0.458,0.146 10 false CANH 5.365,0.271 5.823,0.417 0.458,0.146 10 false CANL 2.083,0.365 2.302,0.51 0.219,0.146 10 false +B 1.417,0.625 1.875,0.771 0.458,0.146 10 false PGND

a.

Disconnect the G117 and G118 seat belt control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G118-1 (CANH) - G118-2 (CANL) L - W Engine switch off 54 to 69 Ω
G118-1 (CANH) - G117-8 (PGND) L - W-B Engine switch off 200 Ω or higher
G118-2 (CANL) - G117-8 (PGND) W - W-B Engine switch off 200 Ω or higher
G118-1 (CANH) - G117-7 (+B) L - W Engine switch off 6 kΩ or higher
G118-2 (CANL) - G117-7 (+B) W - W Engine switch off 6 kΩ or higher



CHECK DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


U170251E03
1.104,0.906 0.875,0.219 0.875,0.219 0.74,0.219 true 1.125,1.104 0.938,1.615 0.938,1.615 0.802,1.615 true 2.344,1.094 2.521,1.458 2.521,1.458 2.667,1.458 true 5.813,1.24 5.938,1.448 5.938,1.448 6.083,1.448 true 1.031,0.917 0.719,0.5 0.719,0.5 0.583,0.5 true 1.031,1.104 0.74,1.365 0.74,1.365 0.604,1.365 true 1.802,0.333 2.229,0.5 0.427,0.167 10 false G119 5.156,0.333 5.542,0.542 0.385,0.208 10 false G48 0.229,0.135 0.771,0.323 0.542,0.188 10 false CA2L*A 0.25,1.531 0.802,1.719 0.552,0.188 10 false CA2H*A 2.688,1.365 3.104,1.552 0.417,0.188 10 false GND 6.115,1.365 6.531,1.552 0.417,0.188 10 false BAT 0.052,0.427 0.604,0.615 0.552,0.188 10 false CA1N*B 0.073,1.281 0.615,1.469 0.542,0.188 10 false CA1P*B

Text in Illustration
*A for V2 Bus *B for Parking Assist Bus

NOTICE:
·

As disconnecting the connector to perform inspections may cause DTCs to be stored, clear DTCs after performing inspections.

·

As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.



a.

Disconnect the G119 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

for V2 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G119-39 (CA2H) - G119-17 (CA2L) G - W Engine switch off 54 to 69 Ω
G119-39 (CA2H) - G119-25 (GND) G - BR Engine switch off 200 Ω or higher
G119-17 (CA2L) - G119-25 (GND) W - BR Engine switch off 200 Ω or higher
G119-39 (CA2H) - G48-16 (BAT) G - GR Engine switch off 6 kΩ or higher
G119-17 (CA2L) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher

for Parking Assist Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G119-40 (CA1P) - G119-18 (CA1N) L - W Engine switch off 108 to 132 Ω
G119-40 (CA1P) - G119-25 (GND) L - BR Engine switch off 200 Ω or higher
G119-18 (CA1N) - G119-25 (GND) W - BR Engine switch off 200 Ω or higher
G119-40 (CA1P) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
G119-18 (CA1N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK PARKING ASSIST ECU (w/ Side Monitor System)


U148937E02
2.406,2.365 2.521,2.365 2.521,2.365 2.656,1.677 true 2.01,2.135 2.125,2.135 2.125,2.135 2.573,1.667 true 5.969,1.031 5.854,1.031 5.854,1.031 5.563,1.521 true 4.646,1.521 4.365,1 4.365,1 4.24,1 true 5.042,0.844 5.177,0.99 0.135,0.146 10 false I6 3.302,0.844 3.438,0.99 0.135,0.146 10 false I7 1.583,2.052 2.042,2.198 0.458,0.146 10 false CANH 6,0.948 6.458,1.094 0.458,0.146 10 false +B 3.823,0.927 4.281,1.073 0.458,0.146 10 false GND1 2.01,2.281 2.469,2.427 0.458,0.146 10 false CANL

a.

Disconnect the I6 and I7 parking assist ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I7-40 (CANH) - I7-39 (CANL) B - W Engine switch off 54 to 69 Ω
I7-40 (CANH) - I6-4 (GND1) B - W-B Engine switch off 200 Ω or higher
I7-39 (CANL) - I6-4 (GND1) W - W-B Engine switch off 200 Ω or higher
I7-40 (CANH) - I6-1 (+B) B - L Engine switch off 6 kΩ or higher
I7-39 (CANL) - I6-1 (+B) W - L Engine switch off 6 kΩ or higher



CHECK CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


a.

for 4 Sensor Type:

U148704E02
3.479,0.75 3.635,0.354 3.635,0.354 3.698,0.354 true 3.135,0.75 3.375,0.177 3.375,0.177 3.448,0.177 true 2.604,1.021 2.167,1.469 2.167,1.469 2.094,1.469 true 6.281,1.094 6.479,1.438 6.479,1.438 6.563,1.438 true 2.573,0.156 2.854,0.313 0.281,0.156 10 false I1 3.74,0.271 3.948,0.427 0.208,0.156 10 false R1 3.479,0.094 3.688,0.25 0.208,0.156 10 false R2 1.979,1.406 2.115,1.563 0.135,0.156 10 false E 5.604,0.156 5.896,0.365 0.292,0.208 10 false G48 6.573,1.375 6.885,1.521 0.313,0.146 10 false BAT

i.

Disconnect the I1 clearance warning ECU assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I1-3 (R1) - I1-5 (R2) R - W Engine switch off 54 to 69 Ω
I1-3 (R1) - I1-17 (E) R - W-B Engine switch off 200 Ω or higher
I1-5 (R2) - I1-17 (E) W - W-B Engine switch off 200 Ω or higher
I1-3 (R1) - G48-16 (BAT) R - GR Engine switch off 6 kΩ or higher
I1-5 (R2) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



b.

for 8 Sensor Type:

U148705E02
3.479,0.75 3.635,0.354 3.635,0.354 3.698,0.354 true 3.125,0.74 3.365,0.167 3.365,0.167 3.438,0.167 true 2.594,1.021 2.156,1.469 2.156,1.469 2.083,1.469 true 6.281,1.094 6.479,1.438 6.479,1.438 6.563,1.438 false 2.458,0.167 2.823,0.323 0.365,0.156 10 false G154 3.75,0.281 3.958,0.438 0.208,0.156 10 false R1 3.479,0.094 3.688,0.25 0.208,0.156 10 false R2 1.979,1.406 2.115,1.563 0.135,0.156 10 false E 5.594,0.156 5.885,0.365 0.292,0.208 10 false G48 6.594,1.365 6.906,1.51 0.313,0.146 10 false BAT

i.

Disconnect the G154 clearance warning ECU assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G154-3 (R1) - G154-5 (R2) R - W Engine switch off 54 to 69 Ω
G154-3 (R1) - G154-17 (E) R - W-B Engine switch off 200 Ω or higher
G154-5 (R2) - G154-17 (E) W - W-B Engine switch off 200 Ω or higher
G154-3 (R1) - G48-16 (BAT) R - GR Engine switch off 6 kΩ or higher
G154-5 (R2) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher




CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (for LED Headlight)


U148706E03
2.927,1.021 3.167,0.438 3.167,0.438 3.24,0.438 true 1.719,0.833 1.417,0.479 1.417,0.479 1.344,0.479 true 1.844,0.833 1.49,0.292 1.49,0.292 1.427,0.292 true 6.281,1.094 6.479,1.448 6.479,1.448 6.563,1.448 true 2.615,0.24 2.99,0.479 0.375,0.24 10 false A58 0.979,0.396 1.396,0.552 0.417,0.156 10 false CANL 1.021,0.219 1.5,0.375 0.479,0.156 10 false CANH 3.292,0.375 3.51,0.531 0.219,0.156 10 false E1 5.594,0.156 5.927,0.385 0.333,0.229 10 false G48 6.604,1.375 6.917,1.521 0.313,0.146 10 false BAT

a.

Disconnect the A58 headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A58-12 (CANH) - A58-13 (CANL) V - W Engine switch off 54 to 69 Ω
A58-12 (CANH) - A58-22 (E1) V - W-B Engine switch off 200 Ω or higher
A58-13 (CANL) - A58-22 (E1) W - W-B Engine switch off 200 Ω or higher
A58-12 (CANH) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
A58-13 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK MULTIPLEX TILT AND TELESCOPIC ECU (for Power Tilt and Power Telescopic Steering Column)


U148531E05
4.594,0.292 4.708,0.292 4.708,0.292 4.854,0.688 true 5.458,0.25 5.344,0.25 5.344,0.25 5.25,0.698 true 5.5,1.625 5.375,1.625 5.375,1.625 5.25,0.958 true 4.604,1.448 4.74,1.448 4.74,1.448 4.865,0.99 true 3.917,0.583 4.292,0.76 0.375,0.177 10 false G116 5.531,1.531 5.938,1.708 0.406,0.177 10 false CANP 5.51,0.177 5.917,0.354 0.406,0.177 10 false CANN 4.396,1.385 4.75,1.625 0.354,0.24 10 false +B 4.26,0.219 4.583,0.396 0.323,0.177 10 false GND

a.

Disconnect the G116 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G116-5 (CANP) - G116-14 (CANN) GR - W Engine switch off 54 to 69 Ω
G116-5 (CANP) - G116-11 (GND) GR - W-B Engine switch off 200 Ω or higher
G116-14 (CANN) - G116-11 (GND) W - W-B Engine switch off 200 Ω or higher
G116-5 (CANP) - G116-2 (+B) GR - G Engine switch off 6 kΩ or higher
G116-14 (CANN) - G116-2 (+B) W - G Engine switch off 6 kΩ or higher



CHECK FRONT POWER SEAT SWITCH LH (w/ Seat Position Memory)


U147960E03
4.938,1.521 4.823,1.521 4.823,1.521 4.354,1.219 true 2.188,1.26 2.292,1.26 2.292,1.26 3.521,0.938 true 4.958,0.854 4.823,0.854 4.823,0.854 4.438,1.188 true 2.229,1.479 2.365,1.479 2.365,1.479 3.521,1.115 true 4.979,1.458 5.385,1.635 0.406,0.177 10 false CANP 4.99,0.781 5.396,0.958 0.406,0.177 10 false CANN 2.031,1.406 2.271,1.594 0.24,0.188 10 false +B 1.854,1.188 2.271,1.375 0.417,0.188 10 false GND 4.167,0.333 4.344,0.49 0.177,0.156 10 false b5 3.167,0.333 3.344,0.49 0.177,0.156 10 false b4

a.

Disconnect the b5 and b4 front power seat switch LH connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
b5-8 (CANP) - b5-7 (CANN) L - W Engine switch off 54 to 69 Ω
b5-8 (CANP) - b4-2 (GND) L - W-B Engine switch off 200 Ω or higher
b5-7 (CANN) - b4-2 (GND) W - W-B Engine switch off 200 Ω or higher
b5-8 (CANP) - b4-7 (+B) L - W Engine switch off 6 kΩ or higher
b5-7 (CANN) - b4-7 (+B) W - W Engine switch off 6 kΩ or higher



CHECK DRIVING SUPPORT SWITCH CONTROL ECU (w/ Multi-function Switch)


a.

for Automatic Transmission:

U170367E03
4.417,1.5 5.042,0.948 5.042,0.948 5.281,0.948 true 5.042,0.729 4.865,0.729 4.865,0.729 4.302,1.5 true 3.771,1.49 3.427,0.865 3.427,0.865 3.271,0.865 true 4.531,1.688 5.063,2.323 5.063,2.323 5.188,2.323 true 4.031,0.667 4.396,0.813 0.365,0.146 10 false G163 5.323,0.865 6.052,1.031 0.729,0.167 10 false CANP 5.052,0.635 5.781,0.802 0.729,0.167 10 false CANN 5.24,2.229 5.969,2.396 0.729,0.167 10 false +B 2.938,0.781 3.667,0.948 0.729,0.167 10 false GND

i.

Disconnect the G163 driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G163-2 (CANP) - G163-3 (CANN) R - W Engine switch off 54 to 69 Ω
G163-2 (CANP) - G163-7 (GND) R - W-B Engine switch off 200 Ω or higher
G163-3 (CANN) - G163-7 (GND) W - W-B Engine switch off 200 Ω or higher
G163-2 (CANP) - G163-8 (+B) R - L Engine switch off 6 kΩ or higher
G163-3 (CANN) - G163-8 (+B) W - L Engine switch off 6 kΩ or higher



b.

for Manual Transmission:

U170606E02
3.135,0.51 3.25,0.51 3.25,0.51 3.729,1.104 false 4.729,1.51 4.615,1.51 4.615,1.51 4.344,1.177 true 4.375,0.51 4.25,0.51 4.25,0.51 3.885,1.104 true 2.417,1.51 2.552,1.51 2.552,1.51 2.823,1.188 true 3.521,0.313 3.844,0.51 0.323,0.198 10 false G76 4.427,0.438 4.885,0.625 0.458,0.188 10 false CANP 2.74,0.438 3.146,0.583 0.406,0.146 10 false CANN 4.771,1.438 5.063,1.625 0.292,0.188 10 false +B 2.083,1.438 2.406,1.583 0.323,0.146 10 false GND

i.

Disconnect the G76 driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G76-9 (CANP) - G76-10 (CANN) R - W Engine switch off 54 to 69 Ω
G76-9 (CANP) - G76-16 (GND) R - W-B Engine switch off 200 Ω or higher
G76-10 (CANN) - G76-16 (GND) W - W-B Engine switch off 200 Ω or higher
G76-9 (CANP) - G76-6 (+B) R - L Engine switch off 6 kΩ or higher
G76-10 (CANN) - G76-6 (+B) W - L Engine switch off 6 kΩ or higher




CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor Sensor)


U170328E02
5.615,1.698 5.792,1.969 5.792,1.969 5.99,1.969 true 2.667,1.24 2.844,0.969 2.844,0.969 3.031,0.969 true 1.865,1.531 1.688,1.802 1.688,1.802 1.49,1.802 true 2.667,1.531 2.844,1.802 2.844,1.802 3.031,1.802 true 2.479,1.24 2.729,0.76 2.729,0.76 2.927,0.76 true 2.479,1.531 2.729,2.01 2.729,2.01 2.927,2.01 true 2.146,0.396 2.469,0.583 0.323,0.188 10 false R42 2.969,0.667 3.573,0.885 0.604,0.219 10 false CA1P*A 3.063,0.885 3.656,1.104 0.594,0.219 10 false CA2P*B 2.958,1.938 3.552,2.146 0.594,0.208 10 false CA1N*A 3.073,1.729 3.719,1.917 0.646,0.188 10 false CA2N*B 4.927,0.573 5.26,0.771 0.333,0.198 10 false G48 6.031,1.896 6.563,2.094 0.531,0.198 10 false BAT 1.063,1.75 1.563,2 0.5,0.25 10 false BLGD

Text in Illustration
*A for V2 Bus *B for Sensor Bus

a.

Disconnect the R42 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

for V2 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R42-2 (CA1P) - R42-7 (CA1N) G - W Engine switch off 54 to 69 Ω
R42-2 (CA1P) - R42-10 (BLGD) G - W-B Engine switch off 200 Ω or higher
R42-7 (CA1N) - R42-10 (BLGD) W - W-B Engine switch off 200 Ω or higher
R42-2 (CA1P) - G48-16 (BAT) G - GR Engine switch off 6 kΩ or higher
R42-7 (CA1N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher

for Sensor Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R42-1 (CA2P) - R42-6 (CA2N) V - W Engine switch off 108 to 132 Ω
R42-1 (CA2P) - R42-10 (BLGD) V - W-B Engine switch off 200 Ω or higher
R42-6 (CA2N) - R42-10 (BLGD) W - W-B Engine switch off 200 Ω or higher
R42-1 (CA2P) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
R42-6 (CA2N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor Sensor)


U170329E02
5.615,1.688 5.792,1.958 5.792,1.958 5.99,1.958 true 2.656,1.24 2.833,0.969 2.833,0.969 3.021,0.969 true 1.865,1.531 1.688,1.802 1.688,1.802 1.49,1.802 true 2.656,1.531 2.833,1.802 2.833,1.802 3.021,1.802 true 2.146,0.406 2.458,0.604 0.313,0.198 10 false R43 3.063,0.885 3.677,1.167 0.615,0.281 10 false CA2P 3.063,1.729 3.625,1.958 0.563,0.229 10 false CA2N 4.927,0.573 5.26,0.792 0.333,0.219 10 false G48 6.01,1.875 6.594,2.094 0.583,0.219 10 false BAT 1.073,1.729 1.563,1.938 0.49,0.208 10 false BRGD

a.

Disconnect the R43 blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R43-1 (CA2P) - R43-6 (CA2N) V - W Engine switch off 108 to 132 Ω
R43-1 (CA2P) - R43-10 (BRGD) V - W-B Engine switch off 200 Ω or higher
R43-6 (CA2N) - R43-10 (BRGD) W - W-B Engine switch off 200 Ω or higher
R43-1 (CA2P) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
R43-6 (CA2N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK TRANSMISSION CONTROL ECU ASSEMBLY (for 1KD-FTV and Automatic Transmission System)


U170042E03
5.188,1.271 4.885,0.615 4.885,0.615 4.75,0.615 true 2.417,1.271 2.719,0.615 2.719,0.615 2.865,0.615 true 6.094,1.833 6.271,2.177 6.271,2.177 6.458,2.177 true 6.26,2.406 6.083,2.406 6.083,2.406 5.927,1.823 true 5.49,0.323 5.823,0.542 0.333,0.219 10 false G70 1.552,0.313 1.906,0.51 0.354,0.198 10 false G69 2.906,0.531 3.26,0.729 0.354,0.198 10 false E1 6.302,2.323 6.823,2.521 0.521,0.198 10 false CAN+ 6.49,2.104 6.948,2.292 0.458,0.188 10 false CAN- 4.375,0.542 4.885,0.74 0.51,0.198 10 false BATT

a.

Disconnect the G69 and G70 transmission control ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G70-21 (CAN+) - G70-20 (CAN-) B - W Engine switch off 108 to 132 Ω
G70-21 (CAN+) - G69-1 (E1) B - BR Engine switch off 200 Ω or higher
G70-20 (CAN-) - G69-1 (E1) W - BR Engine switch off 200 Ω or higher
G70-21 (CAN+) - G70-5 (BATT) B - L Engine switch off 6 kΩ or higher
G70-20 (CAN-) - G70-5 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


U169954E02
1.646,1.146 1.542,1.625 1.542,1.625 1.458,1.625 true 1.875,1.146 1.948,1.625 1.948,1.625 2.042,1.625 true 2.115,1.167 2.427,1.5 2.427,1.5 2.5,1.5 true 5.948,1.271 6.083,1.51 6.083,1.51 6.188,1.51 true 1.698,0.25 1.99,0.417 0.292,0.167 10 false A15 1.073,1.552 1.521,1.75 0.448,0.198 10 false CA1P 2.052,1.542 2.542,1.74 0.49,0.198 10 false CA1N 2.521,1.427 3.021,1.646 0.5,0.219 10 false SGND 5.292,0.333 5.625,0.51 0.333,0.177 10 false G48 6.24,1.427 6.635,1.635 0.396,0.208 10 false BAT

a.

Disconnect the A15 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A15-4 (CA1P) - A15-3 (CA1N) L - W Engine switch off 108 to 132 Ω
A15-4 (CA1P) - A15-2 (SGND) L - BR Engine switch off 200 Ω or higher
A15-3 (CA1N) - A15-2 (SGND) W - BR Engine switch off 200 Ω or higher
A15-4 (CA1P) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
A15-3 (CA1N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK UREA PUMP CONTROL ECU (w/ Urea SCR System)


U170479E02
2.344,2.396 2.406,2.396 2.406,2.396 2.823,1.26 true 3.708,2.531 3.635,2.531 3.635,2.531 3.125,1.271 true 3.219,1.271 3.958,2.26 3.958,2.26 4.031,2.26 true 3.708,1.615 4.354,0.542 4.354,0.542 4.417,0.542 true 3.396,0.229 3.74,0.427 0.344,0.198 10 false s4 4.073,2.188 4.677,2.365 0.604,0.177 10 false CAN- 1.979,2.313 2.542,2.49 0.563,0.177 10 false BATT 4.469,0.458 4.792,0.635 0.323,0.177 10 false E01 3.75,2.458 4.313,2.635 0.563,0.177 10 false CAN+

a.

Disconnect the urea pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
s4-27 (CAN+) - s4-26 (CAN-) G - W Engine switch off 108 to 132 Ω
s4-27 (CAN+) - s4-52 (E01) G - W-B Engine switch off 200 Ω or higher
s4-26 (CAN-) - s4-52 (E01) W - W-B Engine switch off 200 Ω or higher
s4-27 (CAN+) - s4-30 (BATT) G - B Engine switch off 6 kΩ or higher
s4-26 (CAN-) - s4-30 (BATT) W - B Engine switch off 6 kΩ or higher



CHECK NITROGEN OXIDES SENSOR (w/ Urea SCR System)


U170478E03
5.938,1.271 6.177,1.479 6.177,1.479 6.271,1.479 true 1.979,0.906 2.552,0.51 2.552,0.51 2.625,0.51 true 1.875,0.896 1.354,0.385 1.354,0.385 1.25,0.385 true 1.781,0.896 1.135,0.729 1.135,0.729 1.031,0.729 true 1.833,0.25 2.198,0.521 0.365,0.271 10 false s6 5.271,0.26 5.646,0.49 0.375,0.229 10 false G48 0.875,0.302 1.479,0.479 0.604,0.177 10 false CAN- 0.708,0.646 1.104,0.823 0.396,0.177 10 false GND 2.698,0.438 3.26,0.615 0.563,0.177 10 false CAN+ 6.333,1.396 6.698,1.563 0.365,0.167 10 false BAT

a.

Disconnect the nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
s6-4 (CAN+) - s6-3 (CAN-) L - W Engine switch off 54 to 69 Ω
s6-4 (CAN+) - s6-2 (GND) L - W-B Engine switch off 200 Ω or higher
s6-3 (CAN-) - s6-2 (GND) W - W-B Engine switch off 200 Ω or higher
s6-4 (CAN+) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
s6-3 (CAN-) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)


U156734E03
1.26,1.625 1.396,1.625 1.396,1.625 1.552,1.052 false 1.448,1.052 1.167,1.417 1.167,1.417 1.063,1.417 false 3,0.323 2.875,0.323 2.875,0.323 2.458,0.823 false 1.177,0.802 0.948,0.448 0.948,0.448 0.844,0.448 false 1.49,0.302 1.917,0.5 0.427,0.198 10 false G187 0.646,1.344 1.115,1.531 0.469,0.188 10 false CANN 0.865,1.552 1.302,1.729 0.438,0.177 10 false CANP 3.073,0.24 3.438,0.427 0.365,0.188 10 false +B 0.688,0.375 1.052,0.563 0.365,0.188 10 false E

a.

Disconnect the G187 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G187-15 (CANP) - G187-16 (CANN) B - W Engine switch off 54 to 69 Ω
G187-15 (CANP) - G187-4 (E) B - W-B Engine switch off 200 Ω or higher
G187-16 (CANN) - G187-4 (E) W - W-B Engine switch off 200 Ω or higher
G187-15 (CANP) - G187-1 (+B) B - R Engine switch off 6 kΩ or higher
G187-16 (CANN) - G187-1 (+B) W - R Engine switch off 6 kΩ or higher