Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2016.08–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Either Condition is met:
·

"DCM" is not displayed on the "Bus Check" screen.

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "DCM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Telematics transceiver CAN branch wire or connector

·

Power source circuit of telematics transceiver

·

Telematics transceiver ground circuit

·

Telematics transceiver



WIRING DIAGRAM

C306914E48
5.656,1.031 6.125,1.188 0.469,0.156 10 false CANP 5.646,1.542 6.115,1.698 0.469,0.156 10 false CANN 5.656,2.385 6.125,2.542 0.469,0.156 10 false +B 5.646,3.156 6.115,3.313 0.469,0.156 10 false IG2 5.656,3.875 6.125,4.031 0.469,0.156 10 false ACC 5.656,4.396 6.125,4.552 0.469,0.156 10 false E 5.323,0.875 5.542,1.073 0.219,0.198 10 false 15 5.313,1.427 5.542,1.583 0.229,0.156 10 false 16 5.417,3.01 5.615,3.198 0.198,0.188 10 false 7 5.396,2.25 5.594,2.438 0.198,0.188 10 false 1 5.417,3.74 5.615,3.927 0.198,0.188 10 false 8 5.406,4.26 5.604,4.448 0.198,0.188 10 false 4 1.521,0.875 1.677,1.073 0.156,0.198 10 false 7 1.521,1.417 1.75,1.573 0.229,0.156 10 false 18 0.323,1.875 0.792,2.052 0.469,0.177 10 false G193 0.333,2.042 3.24,2.24 2.906,0.198 10 false No. 1 Junction Connector 5.302,4.865 5.698,5.031 0.396,0.167 10 false G187 5.302,5.021 6.844,5.271 1.542,0.25 10 false Telematics Transceiver 4.042,2.198 4.729,2.417 0.688,0.219 10 false MAYDAY 4.229,2.938 5.083,3.125 0.854,0.188 10 false IGN 4.198,3.677 4.969,3.875 0.771,0.198 10 false ACC 2.219,2.365 3.104,2.583 0.885,0.219 10 false from Battery 2.125,3.115 3.167,3.323 1.042,0.208 10 false from IG2 Relay 1.99,3.844 3.063,4.042 1.073,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (TELEMATICS TRANSCEIVER CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (TELEMATICS TRANSCEIVER CAN BRANCH WIRE)
a.
U156361E03
1.115,1.802 1.292,1.802 1.292,1.802 1.823,1.167 false 2.292,1.802 2.125,1.802 2.125,1.802 1.906,1.167 false 0.094,0.073 0.531,0.417 0.438,0.344 10 false *a 1.531,0.271 1.958,0.521 0.427,0.25 10 false G187 0.635,1.729 1.115,1.938 0.479,0.208 10 false CANP 2.365,1.719 2.969,1.969 0.604,0.25 10 false CANN

Disconnect the G187 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-15 (CANP) - G187-16 (CANN) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Telematics Transceiver)



OK

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE TELEMATICS TRANSCEIVER CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BATTERY AND BODY GROUND)
a.
U156362E02
0.438,1.458 0.604,1.458 0.604,1.458 0.948,1.167 false 2.854,0.698 2.698,0.698 2.698,0.698 2.271,0.927 false 0.479,0.635 0.635,0.635 0.635,0.635 0.969,0.938 false 0.656,1.74 0.823,1.74 0.823,1.74 1.052,1.188 false 0.115,0.104 0.552,0.448 0.438,0.344 10 false *a 1.531,0.26 1.927,0.448 0.396,0.188 10 false G187 2.885,0.604 3.042,0.75 0.156,0.146 10 false E 0.219,0.563 0.479,0.708 0.26,0.146 10 false +B 0.281,1.677 0.604,1.823 0.323,0.146 10 false ACC 0.115,1.375 0.438,1.521 0.323,0.146 10 false IG2

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-4 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G187-1 (+B) - Body ground Always 11 to 14 V
G187-7 (IG2) - Body ground Engine switch on (IG) 11 to 14 V
G187-8 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Telematics Transceiver)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR