Home › Engine / Hybrid System › 1KD-FTV (FUEL) › FUEL TANK › 2016.08–2020.08
RM27T0E _51 Engine / Hybrid System _053669 1KD-FTV FUEL _0282661 FUEL TANK A

1KD-FTV FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 2.REMOVE REAR SEAT ASSEMBLY LH

a.

for 60/40 Split Double-folding Seat Type LH Side:

Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side)>REMOVAL).


b.

for 60/40 Split Slide Walk-in Seat Type LH Side:

Remove the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side)>REMOVAL).


Hide 58371F 3.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

Hide 67934 4.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

Hide 67918D 5.REMOVE REAR DOOR SCUFF PLATE LH

Hide 58325E 6.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A220797

Remove the 3 screws and rear floor service hole cover.


b.
A220803E01
0.071,0.057 0.335,0.226 0.265,0.169 12 *A 0.071,2.347 0.327,2.514 0.257,0.167 12 *B

Disconnect the fuel pump and sender gauge connector.

Text in Illustration
*A for Single Tank Type
*B for Double Tank Type


Hide 77606 7.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A220805

Remove the 6 bolts and No. 1 fuel tank protector.


b.
A224491

for Half Cover Type:

Remove the 4 bolts and No. 1 fuel tank protector.


Hide 77209D 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

A223261

Hide 77207A 9.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

A223105

Hide 77209D 10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

A223101

Hide 11.DISCONNECT FUEL CUT OFF TUBE (for Single Tank Type)

A223106

Hide 77012 12.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A223262

Disconnect the fuel tank breather tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77208A 13.DISCONNECT NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223102

Disconnect the No. 4 fuel main tube and fuel suction tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 14.DISCONNECT FUEL CUT OFF TUBE (for Double Tank Type)

a.
A223280

Disconnect the fuel cut off tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77207A 15.DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223281

Disconnect the fuel return tube and No. 2 fuel main tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77012 16.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223282

Disconnect the fuel tank breather tube (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77213B 17.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A220811

Disconnect the fuel tank to filler pipe hose from the filler pipe.


Hide 77100U 18.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Place a transmission jack under the fuel tank.


b.
A220832

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


c.

Slowly lower the transmission jack slightly.


Hide 77651A 19.REMOVE FUEL TANK CUSHION

a.
A220812E01
0.679,0.225 0.863,0.368 0.184,0.143 10 *1 0.886,0.313 0.976,0.313 0.976,0.313 1.176,0.849 false 2.253,0.177 2.437,0.320 0.184,0.143 10 *2 2.46,0.265 2.55,0.265 2.55,0.265 2.75,0.801 false 2.05,1.934 2.234,2.076 0.184,0.143 10 *3 2.257,2.018 2.347,2.018 2.347,2.018 2.547,1.677 false

Remove the No. 1, No. 2 and No. 3 fuel tank cushions from the fuel tank.

Text in Illustration
*1 No. 1 Fuel Tank Cushion
*2 No. 2 Fuel Tank Cushion
*3 No. 3 Fuel Tank Cushion


Hide 77207A 20.REMOVE FUEL RETURN TUBE SUB-ASSEMBLY AND FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A223107E01
2.369,2.868 2.555,3.017 0.185,0.149 10 *2 2.343,2.959 2.246,2.959 2.246,2.959 2.05,3.252 false 0.96,2.869 1.146,3.018 0.185,0.149 10 *1 1.17,2.955 1.267,2.955 1.267,2.955 1.463,3.248 false 2.576,3.199 2.762,3.348 0.185,0.149 10 *3 2.55,3.289 2.453,3.289 2.453,3.289 2.257,3.583 false 0.982,3.863 1.167,4.012 0.185,0.149 10 *4 1.722,3.949 1.192,3.949 false 1.735,3.834 1.312,3.834 1.312,3.834 1.312,3.945 false

Remove the 2 fuel tube joint clips and pull out the fuel return tube and fuel tank main tube.

Text in Illustration
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Fuel Tube Joint Clip
*4 O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A223110

Remove the fuel return tube and fuel tank main tube from the fuel tank.


Hide 77208A 21.REMOVE NO. 4 FUEL MAIN TUBE SUB-ASSEMBLY AND FUEL SUCTION TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223109E01
2.369,2.868 2.555,3.017 0.185,0.149 10 *2 2.343,2.959 2.246,2.959 2.246,2.959 2.05,3.252 false 0.96,2.869 1.146,3.018 0.185,0.149 10 *1 1.17,2.955 1.267,2.955 1.267,2.955 1.463,3.248 false 2.576,3.199 2.762,3.348 0.185,0.149 10 *3 2.55,3.289 2.453,3.289 2.453,3.289 2.257,3.583 false 0.982,3.863 1.167,4.012 0.185,0.149 10 *4 1.722,3.949 1.192,3.949 false 1.735,3.834 1.312,3.834 1.312,3.834 1.312,3.945 false

Remove the 2 fuel tube joint clips and pull out the No. 4 fuel main tube and fuel suction tube.

Text in Illustration
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Fuel Tube Joint Clip
*4 O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A223112

Detach the clamp and remove the No. 4 fuel main tube from the fuel tank.


c.

Detach the clamp and remove the fuel suction tube from the fuel tank.


Hide 77209D 22.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY, FUEL RETURN TUBE SUB-ASSEMBLY AND NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223241E01
2.369,2.868 2.555,3.017 0.185,0.149 10 *2 2.343,2.959 2.246,2.959 2.246,2.959 2.05,3.252 false 0.96,2.869 1.146,3.018 0.185,0.149 10 *1 1.17,2.955 1.267,2.955 1.267,2.955 1.463,3.248 false 2.576,3.199 2.762,3.348 0.185,0.149 10 *3 2.55,3.289 2.453,3.289 2.453,3.289 2.257,3.583 false 0.982,3.863 1.167,4.012 0.185,0.149 10 *4 1.722,3.949 1.192,3.949 false 1.735,3.834 1.312,3.834 1.312,3.834 1.312,3.945 false

Remove the 3 fuel tube joint clips and pull out the fuel tank main tube, fuel return tube and No. 2 fuel main tube.

Text in Illustration
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Fuel Tube Joint Clip
*4 O-Ring

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.




b.
A223243

Detach the clamp and remove the No. 2 fuel main tube from the fuel tank.


c.

Detach the clamp and remove the fuel return tube from the fuel tank.


d.

Remove the fuel tank main tube from the fuel tank.


Hide 77010 23.REMOVE FUEL TANK VENT TUBE ASSEMBLY (for Single Tank Type)

NOTICE:

Protect the connector and tube joint of the fuel tank vent tube assembly with vinyl tape to prevent foreign matter from entering. Then clean off any mud or other foreign matter before proceeding with work.


a.
A387294C02
0.604,1.292 0.604,0.865 0.604,0.865 0.99,0.865 true 0.615,1.135 1.333,1.135 1.333,1.135 1.333,1 true 0.51,1.323 0.823,1.479 0.313,0.156 10 false *a
*a Co-rotation Prevention Check Mark


Apply a co-rotation prevention check mark to the fuel tank vent tube assembly and fuel tank sub-assembly.

NOTICE:
·

The fuel tank sub-assembly cutout is attached to the protrusion on the fuel tank vent tube assembly.

·

If the fuel tank vent tube assembly and fuel tank sub-assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel tank vent tube assembly will co-rotate and result in the fuel tank vent tube assembly and fuel tank sub-assembly being damaged.

·

Make sure to apply a co-rotation prevention check mark to prevent the fuel tank vent tube assembly from co-rotating.




b.
A393131C01
0.719,4.396 1.646,4.135 true 1.208,2.469 1.625,2.74 true 1.667,2.854 2.469,2.583 true 1.063,1.146 1.458,1.281 true 0.615,0.635 0.865,0.802 true 0.792,2.802 0.594,2.292 true 1.5,1.24 1.813,1.396 0.313,0.156 10 false *1 0.458,0.5 0.771,0.656 0.313,0.156 10 false *a 2.479,2.458 2.792,2.615 0.313,0.156 10 false *b 1.073,2.323 1.385,2.479 0.313,0.156 10 false *c 0.552,4.333 0.865,4.49 0.313,0.156 10 false *d 0.49,2.125 0.802,2.281 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a SST (claw set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)


Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

·

Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




c.
A387296C02
2.333,1.313 2.51,1.104 2.51,1.104 2.698,1.104 false 1.146,0.74 1.344,0.74 1.344,0.74 1.75,1.052 false 1.115,2.063 1.313,2.063 1.313,2.063 1.563,1.833 false 2.74,1.021 3.052,1.177 0.313,0.156 10 false *1 0.958,0.667 1.271,0.823 0.313,0.156 10 false *a 0.948,1.979 1.26,2.135 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Press
V100136

SST (Bolt)


While firmly pressing the claw of SST into rib of the fuel pump gauge retainer, tighten the bolt.


d.
A387297C02
0.615,0.438 1.052,0.438 false 0.875,1.906 1.063,1.906 1.063,1.906 1.219,1.563 true 0.448,0.354 0.76,0.51 0.313,0.156 10 false *a 0.698,1.833 1.01,1.99 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).

SST
09808-14031  (09808-01030, 09808-01090)


e.
A387317C02
0.615,1.198 0.854,1.198 0.854,1.198 1.333,0.906 true 1.74,1.083 2.573,1.083 true 2.604,1 2.917,1.198 0.313,0.198 10 true *a 0.427,1.094 0.74,1.25 0.313,0.156 10 false *b
*a Center of Fuel Pump Gauge Retainer
*b SST (Plate)


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.


f.
A393430C01
0.844,3.792 0.74,3.354 true 2.26,3.177 1.875,3.385 true 2.531,3.583 1.719,4.021 true 1.333,1.323 0.469,1.063 true 1.531,0.365 1.615,0.688 true 0.635,3.167 0.948,3.323 0.313,0.156 10 false *1 1.417,0.177 1.729,0.333 0.313,0.156 10 false *a 2.281,3.063 2.594,3.219 0.313,0.156 10 false *b 0.292,0.948 0.604,1.104 0.313,0.156 10 false *c 2.552,3.438 2.865,3.594 0.313,0.156 10 false *d
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V113147

Press


While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).


g.

Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


h.
A387299C03
0.771,0.865 0.969,0.865 0.969,0.865 1.25,0.771 false 1.781,0.24 1.979,0.24 1.979,0.24 2.188,0.521 false 0.615,0.771 0.927,0.927 0.313,0.156 10 false *a 1.615,0.156 1.927,0.313 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Handle)
V100135

Loosen


Slowly loosen the fuel pump gauge retainer by approximately 90°.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.




i.

While one person slowly loosens the fuel pump gauge retainer, have another person press down the rising fuel tank vent tube assembly, securely attach the protrusion of the fuel tank vent tube assembly to the groove of the fuel tank sub-assembly, and then remove the fuel pump gauge retainer while making sure that the fuel tank vent tube assembly is properly aligned.

A387300C02
2.792,3.021 3.24,3.021 3.24,3.021 3.24,2.833 true 0.99,1.885 1.208,1.885 1.208,1.885 1.51,1.375 true 0.854,0.208 1.063,0.208 1.063,0.208 1.146,0.531 true 2.792,3.219 2.792,2.74 2.792,2.74 2.969,2.74 true 0.823,1.792 1.135,1.948 0.313,0.156 10 false *a 0.688,0.125 1,0.281 0.313,0.156 10 false *b 1.521,2.042 1.833,2.198 0.313,0.156 10 false *c 1.938,0.167 2.25,0.323 0.313,0.156 10 false *d 2.729,3.229 3.042,3.385 0.313,0.156 10 false *e 5.448,1.927 5.76,2.083 0.313,0.156 10 false *c 5.75,0.177 6.063,0.333 0.313,0.156 10 false *d
*a SST (Plate) *b SST (Handle)
*c Person in Charge of Loosening *d Person in Charge of Supporting
*e Co-rotation Prevention Check Mark - -


NOTICE:
·

The fuel tank vent tube assembly is equipped with a spring that pushes against the bottom of the fuel tank sub-assembly to constantly lift the fuel tank vent tube assembly upwards.

·

If the fuel tank vent tube assembly and fuel tank sub-assembly are not firmly attached and the fuel pump gauge retainer is rotated, the fuel tank vent tube assembly will co-rotate and result in the fuel tank vent tube assembly and fuel tank sub-assembly being damaged.

·

Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.

·

Do not bend the arm of the fuel sender gauge assembly.




j.

Remove the gasket from the fuel tank sub-assembly.


Hide 77020A 24.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY (for Double Tank Type)

Hide 77643A 25.REMOVE NO. 3 FUEL TANK PROTECTOR

a.
A362964

Remove the 2 bolts.


b.

Detach the 4 clamps and remove the No. 3 fuel tank protector.


Hide 77213B 26.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A220822

Remove the fuel tank to filler pipe hose from the fuel tank.