Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
72173B
1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE LH
Install the rear seat track adjusting handle LH.
Make sure the handle is straight when installing it, and check that it is centered.
71016A
2.INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH
Install the rear seat cushion frame sub-assembly LH with the 6 nuts.
72728
3.INSTALL REAR SEAT INNER RECLINING PROTECTOR RH
Attach the guide and claw to install the rear seat inner reclining protector RH.
71018
4.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH
Temporarily install the rear seatback frame sub-assembly LH with the 2 bolts and 2 "TORX" bolts.
Install the bolt to the bolt hole for the outer belt.
| *1 | Outer Belt Installation Bolt |
Using a T45 "TORX" socket wrench, tighten the 2 "TORX" bolts.
Tighten the 2 bolts.
Remove the bolt from the bolt hole for the outer belt.
82194
5.INSTALL REAR SEAT WIRE LH (w/ Seat Heater System)
Attach the clamp to install the rear seat wire LH to the rear seat cushion frame sub-assembly LH.
Attach the claw to connect the rear seat wire connector to the rear seat upper track rail sub-assembly LH.
87501D
6.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
72068
7.INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH
Install the rear back lock control lever sub-assembly LH with the 2 nuts.
72704B
8.INSTALL REAR NO. 2 SEAT RECLINING CONTROL CABLE
Install the rear No. 2 seat reclining control cable to the seat frame.
Attach the 3 cable clamps and connect the cable.
72704A
9.INSTALL REAR SEAT RECLINING CONTROL CABLE
Install the rear seat reclining control cable to the seat frame.
Attach the 3 cable clamps and connect the rear seat reclining control cable.
Install 4 new cable ties.
73320A
10.INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
73187A
11.INSTALL REAR SEAT SHOULDER BELT GUIDE
Attach the guide and claw to install the rear seat shoulder belt guide.
71499C
12.INSTALL REAR SEAT CUSHION SPRING DAMPER
Install the rear seat cushion spring damper with the 2 nuts.
71879B
13.INSTALL REAR SEAT RECLINING COVER INNER LH
Attach the guide and claw to install the rear seat reclining cover inner LH.
73949
14.INSTALL CAP
Attach the 2 claws to install the cap.
71828B
15.INSTALL REAR SEAT REAR CUSHION MOULDING LH
Move the rear seat rear cushion moulding LH in the direction of the arrow to attach the guide.
Attach the 4 claws and clip to install the rear seat rear cushion moulding LH.
71876J
16.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Attach the 2 claws to install the reclining adjuster inside cover LH.
Install the 2 screws.
71879A
17.INSTALL REAR SEAT INNER RECLINING COVER LH
Attach the guide and install the rear seat inner reclining cover LH with the 2 screws.
71697
18.INSTALL REAR SEATBACK EDGE PROTECTOR
Install the rear seatback edge protector to the rear seatback frame sub-assembly LH.
87510Q
19.INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71078S
20.INSTALL SEPARATE TYPE REAR SEATBACK COVER
Set the separate type rear seatback cover in place.
Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 8 new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the separate type rear seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.
w/ Seat Heater System:
Connect the rear seatback heater assembly wire harness to the separate type rear seatback pad.
21.INSTALL SEATBACK COVER WITH PAD
w/ Seat Heater System:
Install the wire harness as shown in the illustration.
| *a | Paint Mark |
Connect the outer belt to the seatback cover with pad.
Attach the hooks.
| *1 | Hog Ring Pliers |
| *2 | Hook |
| *3 | Hog Ring |
Using hog ring pliers, install the seatback cover with pad with 10 new hog rings.
Be careful not to damage the separate type rear seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.
71931B
22.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.
71890A
23.INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH
Attach the 7 clips to install the rear seatback board carpet assembly LH.
72996A
24.INSTALL REAR SEATBACK COVER
Attach the 4 claws to install the rear seatback cover.
73373
25.INSTALL REAR SEAT SHOULDER BELT COVER
Connect the outer belt to the rear seat shoulder belt cover.
Attach the 2 guides and 2 claws to install the rear seat shoulder belt cover.
73178A
26.INSTALL SEAT BELT ANCHOR COVER CAP
Attach the 2 claws to install the seat belt anchor cover cap.
72058A
27.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly LH.
Install the 2 screws.
72572C
28.INSTALL RECLINING ADJUSTER KNOB CAP LH
Attach the guide and claw to install the reclining adjuster knob cap LH.
73390C
29.INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
Install the rear No. 1 seat inner belt assembly LH and connect the rear No. 1 seat 3 point type belt assembly LH with the bolt.
Do not allow the anchor parts of the rear No. 1 seat 3 point type belt assembly LH and rear No. 1 seat inner belt assembly LH to overlap the protruding parts of the seat cushion frame.
| *1 | Protruding Part |
72978
30.INSTALL CENTER NO. 2 SEATBACK COVER
Install the center No. 2 seatback cover with the 3 screws.
74633A
31.INSTALL COAT HOOK CAP
Attach the guide and 2 claws to install the coat hook cap.
79873
32.INSTALL FOLD SEATBACK WIRE
Attach the 2 claws to install the fold seatback wire.
72663
33.INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER
Install the rear No. 1 seat lock control lever as shown in the illustration.
72660F
34.INSTALL REAR SEAT LOCK ASSEMBLY LH
Install the rear seat lock assembly LH with the 2 bolts.
Attach the clamp to connect the wire.
79157
35.INSTALL NO. 1 SEATBACK COVER
Attach the guide.
Attach the 2 claws to install the No. 1 seatback cover.
71931A
36.INSTALL REAR SEAT HEADREST SUPPORT
Attach the 4 claws to install the 2 rear seat headrest supports.
72877C
37.INSTALL SEAT ARMREST COVER
Install the seat armrest cover to the pad.
Install the seat armrest cover with pad.
Attach the hooks.
71087
38.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY
Attach the 5 clips to install the rear seatback board sub-assembly.
72665B
39.INSTALL REAR SEATBACK LOCK COVER
Move the rear seatback lock cover in the direction of the arrow to attach the clip and 2 guides.
Attach the claw.
72996A
40.INSTALL REAR SEATBACK COVER
Attach the 4 claws to install the rear seatback cover.
72806B
41.INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY
Attach the 2 claws to install the rear seat center armrest cup holder sub-assembly.
Install the 2 screws.
72830
42.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY
Install the rear seat center armrest assembly as shown in the illustration.
Install the armrest support with the nut.
Using a T45 "TORX" socket wrench, install the rear seat center armrest assembly and 2 bushes with the 2 "TORX" bolts.
71349B
43.INSTALL REAR SEATBACK STAY COVER RH
Attach the guide and 3 claws to install the rear seatback stay cover RH.
71369B
44.INSTALL REAR SEATBACK STAY COVER LH
Attach the guide and 3 claws to install the rear seatback stay cover LH.
72731
45.INSTALL REAR SEAT RECLINING BRACKET RH
Using a T45 "TORX" socket wrench, install the rear seat reclining bracket RH and bush with the "TORX" bolt.
72732
46.INSTALL REAR SEAT RECLINING BRACKET LH
Using a T45 "TORX" socket wrench, install the rear seat reclining bracket LH and bush with the "TORX" bolt.
71397A
47.INSTALL CENTER SEAT HINGE COVER
Attach the 2 guides and install the center seat hinge cover with the clip.
71960B
48.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY
Install the rear seat center headrest assembly.
49.INSTALL CENTER SEATBACK ASSEMBLY
Install the center seatback assembly with the 2 bolts.
71647
50.INSTALL REAR SEAT CUSHION EDGE PROTECTOR
Install the rear seat cushion edge protector to the cushion spring.
87510P
51.INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71076S
52.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER
Set the separate type rear seat cushion cover in place.
Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with 14 new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the separate type rear seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.
71696
53.INSTALL REAR NO. 2 SEAT PROTECTOR
Install the 2 rear No. 2 seat protectors to the separate type rear seat cushion pad.
54.INSTALL SEAT CUSHION COVER WITH PAD
Attach the hook.
Attach the hooks to install the seat cushion cover with pad.
w/ Seat Heater System:
Pass the wire harness as shown in the illustration.
Connect the 2 rear seat heater connectors.
72616A
55.INSTALL REAR SEATBACK LOCK STRIKER COVER LH
Attach the 3 clips to install the rear seatback lock striker cover LH.
71826B
56.INSTALL REAR SEAT CUSHION MOULDING LH
Move the rear seat cushion moulding LH in the direction of the arrow to attach the guide.
Attach the 3 claws and clip to install the rear seat cushion moulding LH.
71395B
57.INSTALL CENTER SEAT HINGE COVER LH
Attach the 2 guides and install the center seat hinge cover LH with the clip.
72526A
58.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
Install the reclining adjuster release handle LH with the 3 screws.
71846A
59.INSTALL REAR SEAT UPPER RECLINING COVER LH
Attach the 3 claws to install the rear seat upper reclining cover LH.