Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2016.08–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"PPS" is not displayed on "Bus Check".

·

"Power Steering ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside power steering ECU assembly

·

Power steering ECU assembly CAN branch wire or connector

·

Power steering ECU assembly



WIRING DIAGRAM

E346816E11
0.552,1.427 1.01,1.625 0.458,0.198 10 false G193 0.542,1.604 2.229,1.875 1.688,0.271 10 false No. 1 Junction Connector 1.906,0.49 2.365,0.688 0.458,0.198 10 false 5 1.917,0.885 2.375,1.083 0.458,0.198 10 false 16 5.583,0.49 6.042,0.688 0.458,0.198 10 false 1 5.594,0.875 6.052,1.073 0.458,0.198 10 false 2 5.542,1.552 6,1.75 0.458,0.198 10 false 5 5.563,2.208 6.021,2.406 0.458,0.198 10 false 3 5.813,0.594 6.271,0.792 0.458,0.198 10 false CANH 5.813,1.031 6.271,1.229 0.458,0.198 10 false CANL 5.813,1.688 6.271,1.885 0.458,0.198 10 false IG 5.792,2.354 6.25,2.552 0.458,0.198 10 false GND 4.427,1.542 5.396,1.792 0.969,0.25 10 false ECU-IG NO. 1 2.354,1.677 3.948,2.031 1.594,0.354 10 false from IG1 NO. 1 Relay 5.146,2.729 5.604,2.927 0.458,0.198 10 false G46 5.146,2.885 7.073,3.146 1.927,0.26 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U148346E03
1.917,1.521 2.135,1.063 2.135,1.063 2.229,1.063 false 2.354,1.25 2.281,1.25 2.281,1.25 2.01,1.521 false 0.063,0 0.333,0.229 0.271,0.229 10 false *a 2.396,1.167 2.823,1.333 0.427,0.167 10 false CANH 2.26,0.979 2.677,1.146 0.417,0.167 10 false CANL 0.625,1.365 0.948,1.531 0.323,0.167 10 false G46

Disconnect the G46 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - BATTERY AND BODY GROUND)
a.
U148347E03
1.823,1.521 2.135,1.063 2.135,1.063 2.229,1.063 false 1.323,1.927 1.406,1.927 1.406,1.927 1.625,1.563 false 0.063,0.031 0.333,0.26 0.271,0.229 10 false *a 1.115,1.854 1.281,2.021 0.167,0.167 10 false IG 2.26,0.979 2.625,1.146 0.365,0.167 10 false GND 0.635,1.375 0.958,1.542 0.323,0.167 10 false G46

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G46-5 (IG) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR