The theft warning siren assembly (self power siren) has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren assembly (self power siren) detects this and sounds its siren.
Although the theft warning siren assembly (self power siren) usually sounds by receiving a signal from the main body ECU, the theft warning siren assembly (self power siren) can sound by its internal battery in case the vehicle battery cable is disconnected.
The main body ECU sends an arming signal to the theft warning siren assembly (self power siren) while switching to the armed state, and it sends a disarming signal to the siren while switching to the disarmed state. Also, the main body ECU can cause the theft warning siren assembly (self power siren) to sound by sending an alarm signal during the alarm sounding state.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Operate the intelligent tester according to the steps on the display and select Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Security Horn2 | Theft warning siren (self power siren) | ON/OFF | - |
Siren operates normally.
OK
(See pageVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>PROBLEM SYMPTOMS TABLE)
NG
Disconnect the Q33*1 or Q42*2 siren connector.
*1: for 3 Door
*2: for 5 Door
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q33-2 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q42-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q33-5 (+B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q42-3 (+B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Theft Warning Siren Assembly) |
OK
NG
Using an oscilloscope, check waveform 1.
| *a | Component with harness connected
(Main Body ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | - | - |
| Item | Content |
|---|---|
| Tester Connection | G63-18 (SSCL) - Body ground |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Switched from armed state or arming preparation state to disarmed state |
Using an oscilloscope, check waveform 2.
| Item | Content |
|---|---|
| Tester Connection | G63-18 (SSCL) - Body ground |
| Tool Setting | 2 V/DIV., 20 ms./DIV. |
| Condition | Switched from arming preparation state to armed state |
Waveform is output normally (refer to illustration).
OK
NG
Disconnect the Q33*1 or Q42*2 siren connector.
*1: for 3 Door
*2: for 5 Door
Disconnect the G63 ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q33-4 (CONT) - G63-18 (SSCL) | Always | Below 1 Ω |
| Q33-4 (CONT) or G63-18 (SSCL) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Q42-2 (CONT) - G63-18 (SSCL) | Always | Below 1 Ω |
| Q42-2 (CONT) or G63-18 (SSCL) - Body ground | Always | 10 kΩ or higher |
OK
NG