Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0046  Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance  P0047  Turbocharger/Supercharger Boost Control "A" Circuit Low  P0048  Turbocharger/Supercharger Boost Control "A" Circuit High  


DESCRIPTION

These DTCs indicate that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets certain criteria, the ECM stores a DTC and illuminates the MIL immediately.

The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty ratio of the DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (DC motor stuck off), drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), drivability may deteriorate at intermediate throttle positions or the engine power may be insufficient.

P0046
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds Either condition is met when the motor is operating (1 trip detection logic):
·

DC motor duty ratio is +/-100% for 1.3 seconds or more.

·

DC motor current is 2.2 A or higher for 5 seconds or more.


·

Open or short in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



P0047
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Both conditions are met for 1 second or more when the motor is operating (1 trip detection logic):
·

DC motor duty ratio is 100%.

·

DC motor current is 0.5 A or less.


·

Open in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



P0048
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
2 seconds after engine is started, race engine for 1 second Overcurrent is detected 25 times or more (1 trip detection logic).
·

Short in DC motor (turbocharger sub-assembly) circuit

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



HINT:
·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck closed, the following symptom may appear:

-

Vehicle surge when driving with full load


·

If DTC P0046, P0047 and/or P0048 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

-

Lack of power

-

Vehicle surge or hesitation under light or medium load




WIRING DIAGRAM

A205135E83
2.073,1.406 2.281,1.615 0.208,0.208 10 false 1 5.479,0.74 5.688,0.917 0.208,0.177 10 false 6 5.479,1.406 5.677,1.583 0.198,0.177 10 false 7 5.698,1.292 6.115,1.469 0.417,0.177 10 false M- 6.031,2.01 6.427,2.188 0.396,0.177 10 false ECM 5.698,0.635 6.115,0.813 0.417,0.177 10 false M+ 2.083,0.74 2.281,0.917 0.198,0.177 10 false 2 0.667,2.021 2.021,2.323 1.354,0.302 10 false DC motor 6.021,1.833 6.344,1.99 0.323,0.156 10 false C93 0.656,1.844 1.24,2.073 0.583,0.229 10 false C141 1.771,0.531 2.188,0.708 0.417,0.177 10 false M+ 1.792,1.177 2.208,1.354 0.417,0.177 10 false M-

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047 AND/OR P0048)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
P0046, P0047 and/or P0048 is output A
P0046, P0047 and/or P0048 and other DTCs are output B

HINT:

If codes other than P0046, P0047 and/or P0048 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)

B

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)

OK

CHECK FOR INTERMITTENT PROBLEMS

NG

3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
a.
A182376E02
0.076,0.447 0.280,0.631 0.205,0.184 10 *a

Disconnect the DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (M-) - 2 (M+) Always 1 to 100 Ω


Text in Illustration
*a Component without harness connected
(DC Motor)


c.

Reconnect the DC motor connector.



OK

4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)

NG

6.REPLACE TURBOCHARGER SUB-ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)
a.

Disconnect the DC motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C141-1 (M-) - C93-7 (M-) Always Below 1 Ω
C141-2 (M+) - C93-6 (M+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C141-1 (M-) or C93-7 (M-) - Body ground Always 10 kΩ or higher
C141-2 (M+) or C93-6 (M+) - Body ground Always 10 kΩ or higher



d.

Reconnect the DC motor connector.


e.

Reconnect the ECM connector.



OK

5.REPLACE ECM

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE TURBOCHARGER SUB-ASSEMBLY

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 5 seconds or more.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END