Home › Engine / Hybrid System › 1KD-FTV (INTAKE / EXHAUST) › EXHAUST MANIFOLD W/ TURBOCHARGER › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053679 1KD-FTV INTAKE / EXHAUST _0260647 EXHAUST MANIFOLD W/ TURBOCHARGER A

1KD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53736 6.REMOVE FRONT FENDER APRON SEAL RH

a.

Using a clip remover, remove the 4 clips and front fender apron seal RH.


Hide 53736B 7.REMOVE FRONT NO. 1 FENDER APRON TO FRAME SEAL RH

a.

Using a clip remover, remove the 5 clips and front No. 1 fender apron to frame seal RH.


Hide 53292A 8.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 87452A 9.REMOVE FRONT HEATER BRACKET (for Cold Area Specification Vehicles)

Hide 17881 11.REMOVE NO. 1 AIR CLEANER HOSE

a.
A223211

Loosen the 2 hose clamps and remove the No. 1 air cleaner hose.


Hide 17705 12.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A246272E03
0.031,0.021 0.323,0.219 0.292,0.198 10 true *A 0.031,2.281 0.323,2.521 0.292,0.24 10 true *B

a.

except Cold Area Specification Vehicles:

Detach the 2 clamps and disconnect the mass air flow meter connector.

Text in Illustration
*A except Cold Area Specification Vehicles
*B for Cold Area Specification Vehicles


b.

for Cold Area Specification Vehicles:

Detach the 3 clamps and disconnect the mass air flow meter connector.


c.

Detach the 4 clamps and remove the air cleaner cap sub-assembly.


Hide 17801 13.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 14.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A223214

Remove the 3 bolts and air cleaner case sub-assembly.


Hide 17275A 16.REMOVE COMPRESSOR OUTLET ELBOW

a.
A223215

Detach the 3 wire harness clamps.


b.

Remove the bolt and wire harness bracket.


c.
A220719

Loosen the hose clamp and remove the 2 bolts and compressor outlet elbow.


Hide 87120G 17.REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (for Cold Area Specification Vehicles)

Hide 87101 18.REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (for Cold Area Specification Vehicles)

Hide 88320 19.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 88431 22.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET

Hide 12229 23.REMOVE VENTILATION PIPE

a.
A308001

Type A

Slide the 2 clamps and disconnect the No. 3 turbo water hose and No. 4 turbo water hose from the ventilation pipe.


b.
A308002E02
0.031,0 0.302,0.229 0.271,0.229 10 false *A 0.031,2.333 0.302,2.563 0.271,0.229 10 false *B

Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe from the cylinder head sub-assembly.

Text in Illustration
*A Type A
*B Type B


Hide 11409 24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A220721

Remove the 2 bolts and engine oil level dipstick guide from the cylinder block sub-assembly.


c.

Remove the O-ring from the engine oil level dipstick guide.


Hide 17274 25.REMOVE COMPRESSOR INLET ELBOW

a.
A223216

Detach the 3 wire harness clamps.


b.

Remove the bolt and wire harness bracket from the water inlet.


c.

Disconnect the 2 connectors and detach the wire harness clamp.

A309156E01
3.889,0.048 4.147,0.221 0.258,0.173 10 *B 0.108,0.048 0.365,0.221 0.258,0.173 10 *A

Text in Illustration
*A Type A *B Type B


d.

Slide the clamp and disconnect the No. 2 turbo water hose from the No. 1 turbo water hose sub-assembly.


e.

Slide the clamp and disconnect the No. 3 turbo water hose from the No. 2 water by-pass pipe.


f.

Remove the 2 nuts, compressor inlet elbow and gasket from the turbocharger sub-assembly.


Hide 17271 26.REMOVE NO. 1 TURBO INSULATOR

a.
A220723

Remove the 2 bolts and No. 1 turbo insulator from the turbocharger sub-assembly.


Hide 17167 27.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Remove the bolt and No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 16284 28.DISCONNECT NO. 1 TURBO WATER HOSE

a.
A220724

Disconnect the No. 1 turbo water hose from the No. 1 turbo water pipe sub-assembly.


Hide 17291 29.REMOVE TURBINE OUTLET ELBOW

a.
A220725

Remove the 3 nuts, turbine outlet elbow and gasket from the turbocharger sub-assembly.


Hide 17293 30.REMOVE TURBOCHARGER STAY

a.
A220726

Remove the 2 bolts, nut and turbocharger stay from the turbocharger sub-assembly and cylinder block sub-assembly.


Hide 15407 31.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
U169165E02
0.729,0.417 0.854,0.563 0.125,0.146 10 false A

Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe sub-assembly and 3 gaskets from the turbocharger sub-assembly and cylinder block sub-assembly.

NOTICE:

Do not loosen the nut labeled A in the illustration.



Hide 17141 32.REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY

a.
A220728

Remove the 8 nuts, 8 plate washers and 8 collars from the exhaust manifold with turbocharger sub-assembly.


b.

Remove the exhaust manifold with turbocharger and gasket.


Hide 17201 33.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A220729

Remove the 3 nuts, turbocharger sub-assembly and gasket from the exhaust manifold.


Hide 16027 34.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.
A220730

Remove the 2 nuts, bolt, No. 1 turbo water pipe sub-assembly and gasket from the turbocharger sub-assembly.