Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.

The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.

A128639E44
2.521,2.073 2.854,3.073 false 2.406,2.604 2.208,3.094 false 2.208,0.792 2.406,1.281 false 1.698,0.219 3.25,0.427 1.552,0.208 10 false Throttle Position Sensor 2.896,3.021 3.438,3.219 0.542,0.198 10 false Hall IC 4.375,0.594 4.781,0.802 0.406,0.208 10 false ECM 4.385,1.063 4.677,1.26 0.292,0.198 10 false 5 V 3.5,1.146 3.938,1.344 0.438,0.198 10 false VCVL 3.573,1.76 4.031,1.958 0.458,0.198 10 false VLU 3.5,2.375 3.896,2.573 0.396,0.198 10 false EVLU 3.146,1.135 3.406,1.333 0.26,0.198 10 false VC 3.146,2.375 3.375,2.573 0.229,0.198 10 false E2 3.146,1.76 3.51,1.958 0.365,0.198 10 false VTA 1.698,3.01 2.292,3.219 0.594,0.208 10 false Magnet 1.708,0.656 2.302,0.865 0.594,0.208 10 false Magnet

P0122
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open or short in VLU circuit

·

Open in VC circuit

·

ECM



P0123
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 3 seconds Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open in E2 circuit

·

VC and VLU circuits are short-circuited

·

ECM



HINT:

If DTC P0122 and/or P0123 is stored, the following symptoms may appear:


- Intake booming noise

- Black smoke

- Lack of power

- Vibration at engine stop

- Turbo overspeed, turbo damage


MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

A372458E01
4.646,2.667 5,3.229 5,3.229 5.208,3.229 true 3.375,1 3.708,0.281 3.708,0.281 3.917,0.281 true 1.802,1.292 2.292,1.052 false 1.802,2.854 2.292,2.615 false 0.198,1.677 1.708,2.125 1.51,0.448 10 false Throttle Position Sensor Output Voltage (V) 2.073,0.646 2.99,0.844 0.917,0.198 10 false Closed 2.604,2.698 4.094,2.938 1.49,0.24 10 false Range of Operation 2.479,3.427 4.583,3.719 2.104,0.292 10 false Throttle Valve Opening Angle 3.958,0.208 5.448,0.448 1.49,0.24 10 false Stores P0123 5.271,3.146 6.76,3.385 1.49,0.24 10 false Stores P0122 1.948,0.927 2.563,1.125 0.615,0.198 10 false 5.00 1.958,1.354 2.573,1.552 0.615,0.198 10 false 3.49 1.969,2.375 2.583,2.573 0.615,0.198 10 false 0.69 1.5,2.781 2.115,2.979 0.615,0.198 10 false 0.20 2.25,3.188 2.865,3.385 0.615,0.198 10 false 0 3.948,0.667 4.563,0.865 0.615,0.198 10 false Open 1.51,1.208 2.125,1.406 0.615,0.198 10 false 4.80 4.052,3.198 4.448,3.438 0.396,0.24 10 false 70°

WIRING DIAGRAM

A221590E01
0.74,2.875 2.313,3.059 1.573,0.184 10 Throttle Position Sensor 0.74,2.693 1.059,2.874 0.319,0.180 10 C73 5.441,2.707 5.735,2.877 0.295,0.170 10 C91 5.441,2.889 5.847,3.045 0.406,0.156 10 ECM 5.469,0.928 5.876,1.110 0.408,0.182 10 VCVL 5.469,1.418 5.784,1.609 0.316,0.191 10 VLU 5.469,1.867 5.888,2.037 0.420,0.170 10 EVLU 5.262,0.921 5.401,1.077 0.139,0.156 10 8 5.262,1.404 5.376,1.557 0.114,0.152 10 3 5.262,1.86 5.385,2.002 0.123,0.142 10 9 1.864,1.005 2.083,1.161 0.218,0.156 10 VC 1.794,1.495 2.096,1.644 0.302,0.149 10 VTA 1.878,1.944 2.076,2.107 0.198,0.163 10 E2 2.194,0.921 2.295,1.077 0.101,0.156 10 1 2.194,1.397 2.295,1.553 0.101,0.156 10 3 2.194,1.86 2.295,2.016 0.101,0.156 10 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C73-1 (VC) - C91-8 (VCVL) Always Below 1 Ω
C73-3 (VTA) - C91-3 (VLU) Always Below 1 Ω
C73-2 (E2) - C91-9 (EVLU) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C73-1 (VC) or C91-8 (VCVL) - Body ground Always 10 kΩ or higher
C73-3 (VTA) or C91-3 (VLU) - Body ground Always 10 kΩ or higher
C73-2 (E2) or C91-9 (EVLU) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle position sensor connector.


e.

Reconnect the ECM connector.



OK

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
U169886E01
0.701,1.052 0.978,1.229 0.278,0.177 10 C73 1.098,1.57 1.335,1.724 0.237,0.154 10 VC 0.093,0.058 0.311,0.213 0.218,0.154 10 *a 1.984,1.57 2.212,1.724 0.228,0.154 10 E2 1.772,1.241 2.043,1.57 false

Disconnect the throttle position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C73-1 (VC) - C73-2 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to throttle position sensor)


c.

Reconnect the throttle position sensor connector.



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly (for Bank 1 or Bank 2) (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL).



NEXT

4.READ VALUE USING INTELLIGENT TESTER
4.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.



d.

Enter the following menus: Powertrain / Engine / Data List / Actual Throttle position or Actual Throttle position #2.


e.

Check the movement of the throttle valve when idling the engine after starting it from ignition switch ON.

OK
Condition Tester Display
Ignition switch ON -5 to 5%
Idling 0 to 90%



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END