Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

Vehicles which are equipped with a manual transaxle detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115899E12
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.47,1.96 5.343,2.123 1.873,0.163 10 Combination Meter Assembly 3.113,0.599 3.921,0.776 0.809,0.177 10 4-Pulse 5.039,0.599 5.848,0.776 0.809,0.177 10 4-Pulse 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

P0500
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle at 10 km/h (6.3 mph) or more Conditions (a), (b) and (c) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F).
(b) Injection volume is 19 mm3/st or more.
(c) No speed signal is input to the ECM.
·

Open or short in speedometer circuit

·

Speedometer assembly

·

ECM


Drive the vehicle at 10 km/h (6.3 mph) or more Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed.
(b) No speed signal is input to the ECM.

Related Data List
DTC No. Data List
P0500 Vehicle Speed

WIRING DIAGRAM

A160610E49
0.198,1.802 1.677,1.948 1.479,0.146 10 false from Skid Control ECU 2.146,1.896 2.406,2.073 0.26,0.177 10 false 18 3.917,1.896 4.281,2.063 0.365,0.167 10 false 17 2.417,1.896 2.615,2.063 0.198,0.167 10 false SI 3.635,1.896 3.833,2.063 0.198,0.167 10 false +S 4.948,1.896 5.167,2.063 0.219,0.167 10 false 30 5.969,1.375 6.26,1.542 0.292,0.167 10 false 5 V 5.198,1.625 5.542,1.792 0.344,0.167 10 false SPD 5.667,2.604 6.01,2.771 0.344,0.167 10 false G58 5.667,2.76 6.021,2.927 0.354,0.167 10 false ECM 2.208,2.594 2.771,2.75 0.563,0.156 10 false G304 2.219,2.76 4.115,2.927 1.896,0.167 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:

The vehicle speed sensor is operating normally if the speedometer reading is normal.


OK:

The vehicle speed sensor is operating normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

NG

7.CHECK SPEEDOMETER CIRCUIT
2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the tester.

OK:

Vehicle speed displayed on tester and speedometer display are equal.




OK

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

3.CHECK HARNESS AND CONNECTOR
3.CHECK HARNESS AND CONNECTOR
A372456E02
0.281,0.542 0.729,0.792 0.448,0.25 1.729,1.844 1.875,1.51 true 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 1.615,1.865 1.927,2.063 0.313,0.198 10 false +S 0.344,0.594 0.76,0.792 0.417,0.198 10 false G304

a.

Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-32 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to combination meter assembly)


c.

Reconnect the combination meter assembly connector.



OK

4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
U169133E03
1.542,1.208 1.042,2.031 true 0.125,0.052 0.354,0.281 0.229,0.229 10 false *a 0.177,0.885 1.167,1.167 0.99,0.281 10 false G304 0.74,2.063 1.26,2.25 0.521,0.188 10 false 32 (+S) 2.896,3.573 3.271,3.75 0.375,0.177 10 false GND

a.

Move the shift lever to neutral.


b.

Jack up the vehicle.


c.

Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-32 (+S) - Body ground Ignition switch ON Voltage generated intermittently


Text in Illustration
*a Component with harness connected
(combination meter assembly)

HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


Result
Result Proceed to
OK A
NG B



A

6.REPLACE ECM

B

8.REPLACE COMBINATION METER ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G304-32 (+S) - G58-30 (SPD) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G304-32 (+S) or G58-30 (SPD) - Body ground Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.



OK

6.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK SPEEDOMETER CIRCUIT
a.

Check the speedometer circuit (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).

HINT:

Inspect the brake actuator assembly and speed sensor.




NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at 10 km/h (6.3 mph) or more.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Confirm that the pending DTC is not output again.



NEXT

END