Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.5 mph) or more for more than 20 seconds.

P0617
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.5 mph).
(b) Engine speed is more than 1000 rpm.
(c) STA signal is on.
·

Starter relay circuit

·

Ignition switch assembly

·

Clutch pedal switch assembly*1

·

Park/neutral position switch assembly*2



*1: for Manual Transmission

*2: for Automatic Transmission

Related Data List
DTC No. Data List
P0617 Starter Signal

WIRING DIAGRAM

A311402E03
0.677,8.115 1.135,8.292 0.458,0.177 10 false Battery 1.469,7.448 1.979,7.646 0.51,0.198 10 false Starter 1.729,6.354 2,6.531 0.271,0.177 10 false C95 4.604,4.573 5.01,4.74 0.406,0.167 10 false C159 4.604,4.76 5.5,5.469 0.896,0.708 10 false Park/Neutral Position Switch Assembly*1 4.406,3.75 5.646,4.104 1.24,0.354 10 false Clutch Pedal Switch Assembly*2 4.406,3.573 5.542,3.76 1.135,0.188 10 false r1(*3), A40(*4) 4.271,6.021 4.427,6.198 0.156,0.177 10 false *2 4.271,2.469 4.427,2.646 0.156,0.177 10 false *2 6.208,2.469 6.365,2.646 0.156,0.177 10 false *1 5.969,5.813 6.125,5.99 0.156,0.177 10 false *1 5.979,4.542 6.146,4.75 0.167,0.208 10 false 4 5.76,5.344 5.927,5.552 0.167,0.208 10 false 5 6.135,1.542 6.417,1.719 0.281,0.177 10 false C92 6.115,6.354 6.396,6.531 0.281,0.177 10 false G57 6.177,1.354 6.406,1.552 0.229,0.198 10 false 26 6.198,6.167 6.313,6.313 0.115,0.146 10 false 6 3.542,5.833 3.708,6.042 0.167,0.208 10 false 5 3.542,6.26 3.708,6.469 0.167,0.208 10 false 2 2.75,5.833 2.917,6.042 0.167,0.208 10 false 3 2.75,6.25 2.917,6.458 0.167,0.208 10 false 1 1.563,6.344 1.729,6.552 0.167,0.208 10 false 1 1.542,2.521 3.125,2.729 1.583,0.208 10 false Ignition Switch Assembly 6.552,7.448 6.99,7.667 0.438,0.219 10 false ECM 3.094,6.719 3.333,6.906 0.24,0.188 10 false ST 6.458,6.354 6.781,6.542 0.323,0.188 10 false STA 6.458,1.552 6.938,1.74 0.479,0.188 10 false NSW*1 5.344,1.656 5.5,1.833 0.156,0.177 10 false *1 1.427,3.135 1.75,3.313 0.323,0.177 10 false AM1 4.01,3.479 4.177,3.688 0.167,0.208 10 false 2 4.01,4.135 4.177,4.344 0.167,0.208 10 false 1 0.208,0.083 2.156,0.25 1.948,0.167 10 false w/o Entry and Start System: 0.542,3.135 0.865,3.313 0.323,0.177 10 false ST 1.427,3.969 1.75,4.156 0.323,0.188 10 false ALT 1.531,2.365 1.792,2.51 0.26,0.146 10 false G2 1.823,1.427 2.146,1.604 0.323,0.177 10 false AM1 1.823,2.094 2.146,2.271 0.323,0.177 10 false AM2 2.396,1.427 2.719,1.604 0.323,0.177 10 false ST1 2.396,2.094 2.719,2.271 0.323,0.177 10 false ST2 1.646,1.438 1.75,1.667 0.104,0.229 10 false 2 2.781,1.438 2.885,1.667 0.104,0.229 10 false 1 1.646,1.865 1.75,2.094 0.104,0.229 10 false 7 2.781,1.865 2.885,2.094 0.104,0.229 10 false 8 0.708,6.438 0.958,6.625 0.25,0.188 10 false 1*5 1.042,6.448 1.24,6.625 0.198,0.177 10 false D5 1.042,6.635 1.24,6.813 0.198,0.177 10 false D6 0.708,6.635 0.958,6.823 0.25,0.188 10 false 1*6 3.625,6.74 5.542,6.906 1.917,0.167 10 false *1: for Automatic Transmission 3.635,7.052 5.448,7.208 1.813,0.156 10 false *2: for Manual Transmission 3.635,7.385 4.208,7.542 0.573,0.156 10 false *3: RHD 3.635,7.698 4.167,7.896 0.531,0.198 10 false *4: LHD 3.635,8.01 5.333,8.188 1.698,0.177 10 false *5: Except Cold Area Spec 3.635,8.313 4.896,8.563 1.26,0.25 10 false *6: Cold Area Spec

A269767E08
1.667,5.115 1.896,5.292 0.229,0.177 10 false ST 0.677,8.115 1.135,8.292 0.458,0.177 10 false Battery 1.469,7.448 1.979,7.646 0.51,0.198 10 false Starter 1.729,6.344 2,6.521 0.271,0.177 10 false C95 4.656,4.573 5.094,4.74 0.438,0.167 10 false C159 4.656,4.76 5.552,5.469 0.896,0.708 10 false Park/Neutral Position Switch Assembly*1 4.823,3.75 6.063,4.104 1.24,0.354 10 false Clutch Pedal Switch Assembly*2 4.823,3.573 5.823,3.76 1,0.188 10 false r1(*3), A40(*4) 4.688,6.021 4.844,6.198 0.156,0.177 10 false *2 4.688,2.469 4.844,2.646 0.156,0.177 10 false *2 6.208,2.469 6.365,2.646 0.156,0.177 10 false *1 5.969,5.813 6.125,5.99 0.156,0.177 10 false *1 5.979,4.542 6.146,4.75 0.167,0.208 10 false 4 5.76,5.385 5.927,5.594 0.167,0.208 10 false 5 1.25,0.74 1.521,0.906 0.271,0.167 10 false 14 1.25,1.427 1.792,1.625 0.542,0.198 10 false 10 1.25,3.021 2.01,3.333 0.76,0.313 10 false 12 6.135,1.552 6.417,1.729 0.281,0.177 10 false C92 6.115,6.354 6.396,6.531 0.281,0.177 10 false G57 6.177,1.354 6.385,1.5 0.208,0.146 10 false 26 6.198,6.156 6.313,6.302 0.115,0.146 10 false 6 3.542,5.833 3.708,6.042 0.167,0.208 10 false 5 3.542,6.25 3.708,6.458 0.167,0.208 10 false 2 2.75,5.833 2.917,6.042 0.167,0.208 10 false 3 2.75,6.26 2.917,6.469 0.167,0.208 10 false 1 1.542,6.344 1.708,6.552 0.167,0.208 10 false 1 0.708,6.438 0.958,6.625 0.25,0.188 10 false 1*5 0.167,4.177 3.354,4.583 3.188,0.406 10 false Certification ECU (Smart Key ECU Assembly) 0.229,4.01 0.583,4.208 0.354,0.198 10 false G213 6.531,7.427 6.969,7.646 0.438,0.219 10 false ECM 6.125,0.865 6.406,1.042 0.281,0.177 10 false G58 6.208,0.677 6.375,0.885 0.167,0.208 10 false 1 1.042,6.448 1.24,6.625 0.198,0.177 10 false D5 1.042,6.635 1.24,6.813 0.198,0.177 10 false D6 0.708,6.635 0.958,6.823 0.25,0.188 10 false 1*6 3.625,6.802 5.708,7.01 2.083,0.208 10 false *1: for Automatic Transmission 3.635,7.135 5.594,7.333 1.958,0.198 10 false *2: for Manual Transmission 3.635,7.469 4.208,7.625 0.573,0.156 10 false *3: RHD 3.635,7.771 4.167,7.969 0.531,0.198 10 false *4: LHD 3.635,8.104 5.396,8.323 1.76,0.219 10 false *5: Except Cold Area Spec 3.635,8.406 4.958,8.615 1.323,0.208 10 false *6: Cold Area Spec 3.094,6.719 3.333,6.906 0.24,0.188 10 false ST 6.479,0.865 6.802,1.052 0.323,0.188 10 false NEO 6.469,6.375 6.792,6.563 0.323,0.188 10 false STA 6.479,1.552 6.958,1.74 0.479,0.188 10 false NSW*1 5.344,1.656 5.5,1.833 0.156,0.177 10 false *1 0.844,3.135 1.167,3.313 0.323,0.177 10 false STA 0.76,1.531 1.188,1.698 0.427,0.167 10 false STAR 0.927,0.833 1.156,1.01 0.229,0.177 10 false NE 4.438,3.479 4.604,3.688 0.167,0.208 10 false 2 4.438,4.135 4.604,4.344 0.167,0.208 10 false 1 0.208,0.083 1.906,0.25 1.698,0.167 10 false w/ Entry and Start System:

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter.



PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
a.

Check if the vehicle is equipped with the entry and start system.

Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B



A

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

B

11.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Read the value displayed on the tester when the ignition switch is turned to ON.

OK:
Switch Condition Starter Signal
Ignition switch ON OFF



Result
Result Proceed to
NG (for Manual Transmission) A
NG (for Automatic Transmission) B
OK C


A

3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - CERTIFICATION ECU)

B

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU)

C

26.CONFIRM WHETHER DTC OUTPUT RECURS
3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - CERTIFICATION ECU)
a.

Disconnect the clutch pedal switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A40-2 or G213-10 (STAR) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
r1-2 or G213-10 (STAR) - Body ground Always 10 kΩ or higher



d.

Reconnect the clutch pedal switch assembly connector.


e.

Reconnect the certification ECU (smart key ECU assembly) connector.



OK

4.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the clutch pedal switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
ST relay terminal 2 or A40-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
ST relay terminal 2 or r1-1 - Body ground Always 10 kΩ or higher



d.

Reinstall the ST relay.


e.

Reconnect the clutch pedal switch assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ECM)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch pedal switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G57-6 (STA) or A40-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G57-6 (STA) or r1-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the clutch pedal switch assembly connector.



OK

6.INSPECT CLUTCH PEDAL SWITCH ASSEMBLY

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT CLUTCH PEDAL SWITCH ASSEMBLY
a.

Inspect the clutch pedal switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

21.REPLACE ECM

NG

22.REPLACE CLUTCH PEDAL SWITCH ASSEMBLY
7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU)
a.

Disconnect the park/neutral position switch connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-4 (B) or G213-10 (STAR) - Body ground Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch connector.


e.

Reconnect the certification ECU (smart key ECU assembly) connector.



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 or C159-5 (L) - Body ground Always 10 kΩ or higher



d.

Reinstall the ST relay.


e.

Reconnect the park/neutral position switch connector.



OK

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-5 (L) or G57-6 (STA) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the park/neutral position switch connector.



OK

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

21.REPLACE ECM

NG

23.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
11.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Read the value displayed on the tester when the ignition switch is turned to ON.

OK:
Switch Condition Starter Signal
Ignition switch ON OFF




OK

26.CONFIRM WHETHER DTC OUTPUT RECURS

NG

12.INSPECT IGNITION SWITCH
12.INSPECT IGNITION SWITCH
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1KD-FTV (STARTING)>IGNITION SWITCH>INSPECTION).


Result
Result Proceed to
OK (for Manual Transmission) A
OK (for Automatic Transmission) B
NG C


A

13.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - IGNITION SWITCH)

B

17.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)

C

24.REPLACE IGNITION SWITCH
13.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - IGNITION SWITCH)
a.

Disconnect the clutch pedal switch assembly connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A40-2 or G2-1 (ST1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
r1-2 or G2-1 (ST1) - Body ground Always 10 kΩ or higher



d.

Reconnect the clutch pedal switch assembly connector.


e.

Reconnect the ignition switch assembly connector.



OK

14.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the clutch pedal switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
ST relay terminal 2 or A40-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
ST relay terminal 2 or r1-1 - Body ground Always 10 kΩ or higher



d.

Reinstall the ST relay.


e.

Reconnect the clutch pedal switch assembly connector.



OK

15.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ECM)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL SWITCH ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the clutch pedal switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G57-6 (STA) or A40-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G57-6 (STA) or r1-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the clutch pedal switch assembly connector.



OK

16.INSPECT CLUTCH PEDAL SWITCH ASSEMBLY

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.INSPECT CLUTCH PEDAL SWITCH ASSEMBLY
a.

Inspect the clutch pedal switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).



OK

21.REPLACE ECM

NG

22.REPLACE CLUTCH PEDAL SWITCH ASSEMBLY
17.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH)
a.

Disconnect the park/neutral position switch connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-4 (B) or G2-1 (ST1) - Body ground Always 10 kΩ or higher



d.

Reconnect the park/neutral position switch connector.


e.

Reconnect the ignition switch assembly connector.



OK

18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 or C159-5 (L) - Body ground Always 10 kΩ or higher



d.

Reinstall the ST relay.


e.

Reconnect the park/neutral position switch connector.



OK

19.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
19.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-5 (L) or G57-6 (STA) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the park/neutral position switch connector.



OK

20.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

21.REPLACE ECM

NG

23.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
21.REPLACE ECM

NEXT

26.CONFIRM WHETHER DTC OUTPUT RECURS
22.REPLACE CLUTCH PEDAL SWITCH ASSEMBLY
a.

Replace the clutch pedal switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL).



NEXT

26.CONFIRM WHETHER DTC OUTPUT RECURS
23.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Replace the park/neutral position switch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).



NEXT

26.CONFIRM WHETHER DTC OUTPUT RECURS
24.REPLACE IGNITION SWITCH
a.

Replace the ignition switch assembly (See page Engine / Hybrid System>1KD-FTV (STARTING)>IGNITION SWITCH>REMOVAL).



NEXT

26.CONFIRM WHETHER DTC OUTPUT RECURS
25.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

26.CONFIRM WHETHER DTC OUTPUT RECURS
26.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.5 mph) or more and an engine speed of 1000 rpm or more.


f.

Confirm that the DTC is not output again.



NEXT

END