Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A221597E13
4.208,1.427 4.208,0.583 false 4.208,0.583 4.563,0.583 false 1.375,3.094 1.5,3.333 true 1.073,2.292 0.708,1.25 true 1.375,1.75 1.552,1.271 true 0.708,1.24 0.802,1.24 false 1.552,1.26 1.646,1.26 false 0.5,3.875 2.406,4.302 1.906,0.427 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.844,1.167 1.313,1.333 0.469,0.167 10 false Hall IC 3.01,2.354 3.406,2.531 0.396,0.177 10 false VTA1 3.01,3.135 3.406,3.313 0.396,0.177 10 false VNE2 3.01,1.552 3.469,1.729 0.458,0.177 10 false VNVC 3.094,3.542 3.479,3.76 0.385,0.219 10 false ECM 4.719,3.604 5.229,3.781 0.51,0.177 10 false Closed 5.719,3.604 6.302,3.781 0.583,0.177 10 false Opened 1.688,1.177 2.167,1.354 0.479,0.177 10 false Magnet 4.615,0.5 6.448,0.896 1.833,0.396 10 false Nozzle Vane Position Sensor Output Voltage (V) 0.063,2.688 0.531,3.073 0.469,0.385 10 false Sensor Vane 4.104,1.531 4.365,1.708 0.26,0.177 10 false 4.5 4.104,2.396 4.375,2.573 0.271,0.177 10 false 0.5 1.438,3.354 1.917,3.531 0.479,0.177 10 false Magnet 4.781,3.229 6.219,3.531 1.438,0.302 10 true Nozzle Vane Position

P2564
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTA1 voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM



P2565
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTA1 voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

ECM



HINT:

If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:

- Lack of power

- Vehicle surge or hesitation under light or medium load



WIRING DIAGRAM

A221590E37
0.74,2.823 2.583,3.396 1.844,0.573 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.74,2.646 1.573,2.927 0.833,0.281 10 false C87 5.896,2.833 6.729,3.167 0.833,0.333 10 false ECM 5.469,0.927 5.875,1.104 0.406,0.177 10 false VNVC 5.469,1.406 6.094,1.646 0.625,0.24 10 false VTA1 5.469,1.854 5.885,2.021 0.417,0.167 10 false VNE2 5.208,0.917 6.125,1.333 0.917,0.417 10 false 11 5.26,1.406 5.833,1.792 0.573,0.385 10 false 6 5.208,1.865 5.854,2.24 0.646,0.375 10 false 10 1.656,1.031 2.469,1.406 0.813,0.375 10 false VNVC 1.698,1.5 2.292,1.823 0.594,0.323 10 false VTA1 1.688,1.958 2.219,2.396 0.531,0.438 10 false VNE2 2.198,0.917 2.792,1.385 0.594,0.469 10 false 3 2.198,1.396 2.74,1.708 0.542,0.313 10 false 1 2.198,1.854 2.667,2.229 0.469,0.375 10 false 2 5.896,2.646 6.583,2.927 0.688,0.281 10 false C91

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 AND P2565)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
P2564 and/or P2565 is output A
P2564 and/or P2565 and other DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)

B

2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C87-1 (VTA1) - C91-6 (VTA1) Always Below 1 Ω
C87-2 (VNE2) - C91-10 (VNE2) Always Below 1 Ω
C87-3 (VNVC) - C91-11 (VNVC) Always Below 1 Ω



Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C87-1 (VTA1) or C91-6 (VTA1) - Body ground Always 10 kΩ or higher
C87-2 (VNE2) or C91-10 (VNE2) - Body ground Always 10 kΩ or higher
C87-3 (VNVC) or C91-11 (VNVC) - Body ground Always 10 kΩ or higher


d.

Reconnect the nozzle vane position sensor connector.


e.

Reconnect the ECM connector.



OK

3.INSPECT ECM (VNVC VOLTAGE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM (VNVC VOLTAGE)
a.
U169106E02
1.99,0.802 2.49,1.76 true 1.927,0.802 1.365,1.74 true 2.156,1.802 2.927,2.042 0.771,0.24 10 false 10 (VNE2) 0.938,1.771 1.823,2.01 0.885,0.24 10 false 11 (VNVC) 0.167,0.115 0.479,0.333 0.313,0.219 10 false *a 1.906,0.281 2.292,0.51 0.385,0.229 10 false C91

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C91-11 (VNVC) - C91-10 (VNE2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)



OK

4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

NG

5.REPLACE ECM
4.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off and leave the vehicle for 15 seconds.


d.

Turn the ignition switch to ON for 1 second.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P2564 and/or P2565.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.




NEXT

END