Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  U1115  Lost Communication with Tilt and Telescopic Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U1115 Lost Communication with Tilt and Telescopic Module There is no communication from the multiplex tilt and telescopic ECU.
·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Power source circuit of multiplex tilt and telescopic ECU

·

Multiplex tilt and telescopic ECU ground circuit

·

Multiplex tilt and telescopic ECU


Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

E346818E03
0.208,1.969 0.823,2.167 0.615,0.198 10 false G288 0.208,2.146 2.188,2.542 1.979,0.396 10 false No. 4 CAN Junction Connector 1.948,0.958 2.563,1.156 0.615,0.198 10 false 3 1.938,1.365 2.552,1.563 0.615,0.198 10 false 14 5.063,0.938 5.677,1.135 0.615,0.198 10 false 3 5.042,1.385 5.656,1.583 0.615,0.198 10 false 11 5.281,1.052 5.896,1.25 0.615,0.198 10 false CANP 5.281,1.479 5.896,1.677 0.615,0.198 10 false CANN 5.281,1.969 5.896,2.167 0.615,0.198 10 false +B 5.281,2.396 5.896,2.594 0.615,0.198 10 false ECUB 5.302,2.781 5.917,2.979 0.615,0.198 10 false IG 5.271,3.26 5.885,3.458 0.615,0.198 10 false GND 5.094,3.125 5.708,3.323 0.615,0.198 10 false 1 4.75,3.802 5.365,4 0.615,0.198 10 false G211 4.75,3.948 6.875,4.24 2.125,0.292 10 false Multiplex Tilt and Telescopic ECU 5.031,2.708 5.646,2.906 0.615,0.198 10 false 10 5.083,2.313 5.698,2.51 0.615,0.198 10 false 9 5.083,1.896 5.698,2.094 0.615,0.198 10 false 2 4.333,1.844 4.948,2.042 0.615,0.198 10 false TI&TE 4.323,2.271 4.938,2.469 0.615,0.198 10 false ECU-B 3.948,2.656 4.802,2.854 0.854,0.198 10 false ECU-IG NO.1 2.104,2.802 3.469,3.083 1.365,0.281 10 false from IG NO.1 Relay 2.542,2.375 3.865,2.604 1.323,0.229 10 false from Battery 2.573,1.969 3.896,2.198 1.323,0.229 10 false from Battery

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check for DTCs.

HINT:

If DTC U1002 is output from the gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) A
DTC U1002 is output from main body ECU (multiplex network body ECU) B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU BRANCH WIRE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (MULTIPLEX TILT AND TELESCOPIC ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369151C15
1.5,0.333 1.917,0.583 0.417,0.25 1.219,1.771 1.417,1.25 1.417,1.25 1.583,1.25 true 1.219,2.052 1.417,2.5 1.417,2.5 1.583,2.5 true 1.625,1.188 2.104,1.375 0.479,0.188 10 false CANP 1.615,2.448 2.094,2.635 0.479,0.188 10 false CANN 0.125,0.135 0.604,0.323 0.479,0.188 10 false *a 1.542,0.385 2.021,0.573 0.479,0.188 10 false G211
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the multiplex tilt and telescopic ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-3 (CANP) - G211-11 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369151C16
1.5,0.333 1.917,0.583 0.417,0.25 1.031,2.063 1.146,2.521 1.146,2.521 1.313,2.521 true 0.615,1.74 0.906,1.083 0.906,1.083 1.073,1.083 true 0.833,1.74 1.073,1.25 1.073,1.25 1.24,1.25 true 0.802,2.063 1,2.708 1,2.708 1.167,2.708 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.542,0.375 1.969,0.604 0.427,0.229 10 false G211 1.125,1.021 1.552,1.229 0.427,0.208 10 false GND 1.302,1.188 1.729,1.396 0.427,0.208 10 false +B 1.375,2.438 1.802,2.646 0.427,0.208 10 false IG 1.208,2.625 1.635,2.833 0.427,0.208 10 false ECUB
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G211-1 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G211-2 (+B) - Body ground Always 11 to 14 V
G211-9 (ECUB) - Body ground Always 11 to 14 V
G211-10 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)