Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  U1002  Lost Communication with Gateway Module  


DESCRIPTION

·

The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the sub bus 1.

·

When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the sub bus 1, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the sub bus 1. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the sub bus 1 when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to the sub bus 1, the main body ECU (multiplex network body ECU) determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U1002 Lost Communication with Gateway Module Lost communication with the gateway module.
·

Open or short in sub bus 1 CAN main wire or connector

·

Open or short in sub bus 1 CAN branch wire or connector

·

Main body ECU (multiplex network body ECU)

·

Front power seat switch (power seat control ECU) (w/ Seat Memory)

·

Outer mirror control ECU assembly LH (w/ Reverse Shift-linked Mirror)

·

Outer mirror control ECU assembly RH (w/ Reverse Shift-linked Mirror)

·

Multiplex tilt and telescopic ECU (for Power Tilt and Power Telescopic Steering Column)

·

Rear television camera assembly (w/ Rear Television Camera Assembly [built-in ECU])

·

No. 4 CAN junction connector

·

No. 2 CAN junction terminal


Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C382808E04
5.188,1.365 5.802,1.563 0.615,0.198 10 false G216 5.198,1.552 6.865,1.938 1.667,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.729,0.531 6.031,0.74 0.302,0.208 10 false 9 5.677,0.948 5.979,1.156 0.302,0.208 10 false 10 5.938,0.531 6.396,0.74 0.458,0.208 10 false CANP 5.917,1.156 6.375,1.365 0.458,0.208 10 false CANN 3.906,0.542 4.208,0.75 0.302,0.208 10 false 4 3.875,0.938 4.177,1.146 0.302,0.208 10 false 15 3.198,0.552 3.5,0.76 0.302,0.208 10 false 1 3.135,0.906 3.438,1.115 0.302,0.208 10 false 12 1.354,0.552 1.656,0.76 0.302,0.208 10 false 9 1.354,0.896 1.656,1.104 0.302,0.208 10 false 8 0.188,1.24 0.49,1.448 0.302,0.208 10 false J12 0.167,1.406 2.969,1.938 2.802,0.531 10 false Outer Mirror Control ECU Assembly RH*8 0.146,5.479 1.938,5.76 1.792,0.281 10 false *1: w/ Seat Memory 0.146,5.823 2.51,6.198 2.365,0.375 10 false *2: for Power Tilt and Power Telescopic Steering Column 0.146,6.344 2.615,6.719 2.469,0.375 10 false *3: w/ Rear Television Camera Assembly (built-in ECU) 5,3.146 5.708,3.354 0.708,0.208 10 false a5*6, b5*7 0.875,0.667 1.333,0.875 0.458,0.208 10 false CANP 0.865,1.042 1.323,1.25 0.458,0.208 10 false CANN 5.01,3.302 7.031,3.708 2.021,0.406 10 false Front Power Seat Switch (Power Seat Control ECU)*1 5.958,2.521 6.417,2.729 0.458,0.208 10 false CANP 5.948,2.906 6.406,3.115 0.458,0.208 10 false CANN 5.729,2.396 6.031,2.604 0.302,0.208 10 false 8 5.729,2.771 6.031,2.979 0.302,0.208 10 false 7 3.885,2.344 4.188,2.552 0.302,0.208 10 false 2 3.875,2.792 4.177,3 0.302,0.208 10 false 13 0.146,3.104 0.594,3.354 0.448,0.25 10 false G211 0.156,3.292 2.375,3.677 2.219,0.385 10 false Multiplex Tilt and Telescopic ECU*2 3.177,2.385 3.479,2.594 0.302,0.208 10 false 3 3.115,2.802 3.417,3.01 0.302,0.208 10 false 14 1.365,2.406 1.667,2.615 0.302,0.208 10 false 3 1.344,2.792 1.646,3 0.302,0.208 10 false 11 0.885,2.531 1.344,2.74 0.458,0.208 10 false CANP 0.833,2.896 1.292,3.104 0.458,0.208 10 false CANN 3.906,4.052 4.208,4.26 0.302,0.208 10 false 6 3.896,4.479 4.198,4.688 0.302,0.208 10 false 17 5.708,4.115 6.01,4.323 0.302,0.208 10 false 9 5.729,4.49 6.031,4.698 0.302,0.208 10 false 8 4.323,4.813 4.938,5.01 0.615,0.198 10 false K12 4.302,4.958 7.104,5.49 2.802,0.531 10 false Outer Mirror Control ECU Assembly LH*8 5.917,4.198 6.375,4.406 0.458,0.208 10 false CANP 5.927,4.594 6.385,4.802 0.458,0.208 10 false CANN 5.302,6.51 5.917,6.708 0.615,0.198 10 false G299 5.292,6.677 7.156,6.958 1.865,0.281 10 false No. 2 CAN Junction Terminal 5.917,5.854 6.375,6.063 0.458,0.208 10 false CANP 5.948,6.417 6.406,6.625 0.458,0.208 10 false CANN 5.719,5.781 6.021,5.99 0.302,0.208 10 false 3 5.729,6.208 6.031,6.417 0.302,0.208 10 false 2 0.188,4.948 2.406,5.333 2.219,0.385 10 false Rear Television Camera Assembly*3 0.875,4.198 1.333,4.406 0.458,0.208 10 false CANH 0.844,4.604 1.302,4.813 0.458,0.208 10 false CANL 1.354,4.229 1.802,4.479 0.448,0.25 10 false X10 1.365,4.01 1.813,4.26 0.448,0.25 10 false 4*4 1.354,4.625 1.802,4.875 0.448,0.25 10 false X10 1.354,4.448 1.802,4.698 0.448,0.25 10 false 1*4 1.75,4.229 2.198,4.479 0.448,0.25 10 false v3 1.729,4.021 2.177,4.271 0.448,0.25 10 false 4*5 1.771,4.615 2.219,4.865 0.448,0.25 10 false v3 1.74,4.427 2.188,4.677 0.448,0.25 10 false 1*5 3.198,4.083 3.5,4.292 0.302,0.208 10 false 5 3.135,4.49 3.438,4.698 0.302,0.208 10 false 16 0.135,6.917 2.5,7.292 2.365,0.375 10 false *4: w/o Tire Carrier 1.479,6.927 3.844,7.302 2.365,0.375 10 false *5: w/ Tire Carrier 2.958,6.573 3.531,6.781 0.573,0.208 10 false G288 2.969,6.74 5,7.104 2.031,0.365 10 false No. 4 CAN Junction Connector 3.875,6.208 4.177,6.417 0.302,0.208 10 false 18 3.927,5.823 4.229,6.031 0.302,0.208 10 false 7 0.146,7.354 2.146,7.604 2,0.25 10 false *6: for RHD 1.479,7.354 3.479,7.604 2,0.25 10 false *7: for LHD 2.771,7.365 4.771,7.615 2,0.25 10 false *8: w/ Reverse Shift-linked Mirror

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click here

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click here

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click here



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK SUB BUS 1
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C216700C20
0.531,2.51 0.958,2.75 0.427,0.24 0.479,0.875 0.917,1.115 0.438,0.24 1.719,0.896 1.375,0.229 1.375,0.229 1.188,0.229 true 1.427,0.885 1.146,0.542 1.146,0.542 1.01,0.542 true 2.146,2.802 2.292,3.083 2.292,3.083 2.469,3.083 true 1.969,0.875 2.104,0.51 2.104,0.51 2.292,0.51 true 0.104,1.958 0.323,2.156 0.219,0.198 10 false *b 0.104,0.073 0.323,0.271 0.219,0.198 10 false *a 0.781,0.156 1.313,0.375 0.531,0.219 10 false CANN 0.583,0.469 1.031,0.667 0.448,0.198 10 false CANP 2.531,3.01 2.844,3.208 0.313,0.198 10 false BAT 0.615,2.552 0.906,2.75 0.292,0.198 10 false G48 0.573,0.917 1.021,1.135 0.448,0.219 10 false G299 2.344,0.438 2.854,0.677 0.51,0.24 10 false E
*a Component with harness connected
(No. 2 CAN Junction Terminal)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Resistance: Malfunction
G299-3 (CANP) - G299-2 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 53 Ω: Short in line
G299-3 (CANP) - G299-2 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G299-3 (CANP) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
G299-2 (CANN) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
G299-3 (CANP) - G299-1 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short
G299-2 (CANN) - G299-1 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short



Result:
Result Proceed to
OK A
NG
- Open in CAN main wire
B
NG
- Short in CAN bus wire
C
NG
- +B short
- Ground short
D



A

2.CHECK FOR DTC

B

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)

C

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)

D

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)
2.CHECK FOR DTC
a.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Clear the DTCs.


c.

Check for DTCs.


Result:
Result Proceed to
DTC U1002 is output from main body ECU (multiplex network body ECU) A
Other DTC is output B



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.
C379589C31
1.417,0.115 1.896,0.375 0.479,0.26 1.906,1.677 2.104,0.771 2.104,0.771 2.271,0.771 true 1.906,2.052 2.021,2.656 2.021,2.656 2.188,2.656 true 1.385,1.729 1.083,0.75 1.083,0.75 0.917,0.75 true 1.417,2.042 1.063,2.667 1.063,2.667 0.896,2.667 true 1.49,0.167 2.104,0.365 0.615,0.198 10 false G288 2.323,0.698 3.24,0.896 0.917,0.198 10 false CANH*c 2.24,2.594 3.156,2.792 0.917,0.198 10 false CANL*c 0.344,0.698 1.26,0.896 0.917,0.198 10 false CANH*b 0.365,2.604 1.281,2.802 0.917,0.198 10 false CANL*b 0.052,0.083 0.969,0.281 0.917,0.198 10 false *a
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to No. 2 CAN Junction Terminal


Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G288-4 (CANH) - G288-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)
G288-7 (CANH) - G288-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction terminal



Result:
Result Proceed to
OK A
NG (Main body ECU [multiplex network body ECU] CAN main wire) B
NG (No. 2 CAN junction terminal CAN main wire) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

4.CONNECT CONNECTOR

C

6.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the G288 No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C379611C04
0.188,1 0.604,1.271 0.417,0.271 1.49,1.135 1.406,0.302 1.406,0.302 1.156,0.302 true 1.615,1.135 1.698,0.302 1.698,0.302 1.948,0.302 true 0.229,1.052 0.688,1.25 0.458,0.198 10 false G216 0.063,0.052 0.521,0.25 0.458,0.198 10 false *a 0.74,0.219 1.198,0.417 0.458,0.198 10 false CANP 2,0.229 2.458,0.427 0.458,0.198 10 false CANN
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G216-9 (CANP) - G216-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - NO. 4 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the G288 No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
C210060C76
0.323,0.917 0.802,1.167 0.479,0.25 0.948,0.521 1.115,0.521 1.115,0.521 1.344,0.896 true 2.188,0.406 2.01,0.406 2.01,0.406 1.677,0.917 true 0.521,0.438 0.958,0.615 0.438,0.177 10 false CANP 0.427,0.958 0.844,1.188 0.417,0.229 10 false G299 0.063,0.063 0.271,0.24 0.208,0.177 10 false *a 2.229,0.313 2.667,0.49 0.438,0.177 10 false CANN
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)


Disconnect the No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G299-3 (CANP) - G299-2 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)
a.
C379589C32
0.146,1.583 0.625,1.844 0.479,0.26 0.875,1.688 0.875,0.854 0.875,0.854 0.708,0.854 true 0.875,2.042 0.875,2.625 0.875,2.625 0.708,2.625 true 1.052,1.688 1.052,0.688 1.052,0.688 0.885,0.688 true 1.219,1.688 1.219,0.521 1.219,0.521 1.052,0.521 true 1.385,1.688 1.385,0.354 1.385,0.354 1.219,0.354 true 1.552,1.688 1.552,0.354 1.552,0.354 1.719,0.354 true 1.719,1.688 1.719,0.521 1.719,0.521 1.885,0.521 true 1.875,1.688 1.875,0.771 1.875,0.771 2.042,0.771 true 1.052,2.052 1.052,2.833 1.052,2.833 0.885,2.833 true 1.219,2.063 1.219,3 1.219,3 1.052,3 true 1.385,2.042 1.385,3.208 1.385,3.208 1.219,3.208 true 1.573,2.063 1.573,3.229 1.573,3.229 1.74,3.229 true 1.719,2.073 1.719,2.99 1.719,2.99 1.885,2.99 true 1.906,2.052 1.906,2.719 1.906,2.719 2.073,2.719 true 0.25,1.635 0.865,1.833 0.615,0.198 10 false G288 1.781,0.281 2.698,0.479 0.917,0.198 10 false CANH*f 2.115,2.667 3.031,2.865 0.917,0.198 10 false CANL*h 0.156,0.792 1.073,0.99 0.917,0.198 10 false CANH*b 0.167,2.542 1.083,2.74 0.917,0.198 10 false CANL*b 0.052,0.083 0.969,0.281 0.917,0.198 10 false *a 0.313,0.604 1.229,0.802 0.917,0.198 10 false CANH*c 0.5,0.438 1.417,0.635 0.917,0.198 10 false CANH*d 0.656,0.271 1.573,0.469 0.917,0.198 10 false CANH*e 1.927,0.458 2.844,0.656 0.917,0.198 10 false CANH*g 2.094,0.698 3.01,0.896 0.917,0.198 10 false CANH*h 0.354,2.76 1.271,2.958 0.917,0.198 10 false CANL*c 0.521,2.927 1.438,3.125 0.917,0.198 10 false CANL*d 0.688,3.135 1.604,3.333 0.917,0.198 10 false CANL*e 1.813,3.167 2.729,3.365 0.917,0.198 10 false CANL*f 1.938,2.906 2.854,3.104 0.917,0.198 10 false CANL*g
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Outer Mirror Control ECU Assembly RH (w/ Reverse Shift-linked Mirror)
*c to Front Power Seat Switch (Power Seat Control ECU) (w/ Seat Memory)
*d to Multiplex Tilt and Telescopic ECU (for Power Tilt and Power Telescopic Steering Column)
*e to Main Body ECU (Multiplex Network Body ECU)
*f to Rear Television Camera Assembly (w/ Rear Television Camera Assembly [built-in ECU])
*g to Outer Mirror Control ECU Assembly LH (w/ Reverse Shift-linked Mirror)
*h to No. 2 CAN Junction Terminal


Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Seat Memory

*2: for Power Tilt and Power Telescopic Steering Column

*3: w/ Rear Television Camera Assembly (built-in ECU)

*4: w/ Reverse Shift-linked Mirror

G288-1 (CANH) - G288-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly RH*4
G288-2 (CANH) - G288-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Front power seat switch (power seat control ECU)*1
G288-3 (CANH) - G288-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Multiplex tilt and telescopic ECU*2
G288-4 (CANH) - G288-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Main body ECU (multiplex network body ECU)
G288-5 (CANH) - G288-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rear television camera assembly*3
G288-6 (CANH) - G288-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly LH*4
G288-7 (CANH) - G288-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction terminal



Result:
Result Proceed to
OK A
NG (Main body ECU [multiplex network body ECU] CAN main wire) B
NG (No. 2 CAN junction terminal CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

9.CONNECT CONNECTOR

C

11.CONNECT CONNECTOR

D

16.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
9.CONNECT CONNECTOR
a.

Reconnect the G288 No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
10.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C379611C04
0.188,1 0.604,1.271 0.417,0.271 1.49,1.135 1.406,0.302 1.406,0.302 1.156,0.302 true 1.615,1.135 1.698,0.302 1.698,0.302 1.948,0.302 true 0.229,1.052 0.688,1.25 0.458,0.198 10 false G216 0.063,0.052 0.521,0.25 0.458,0.198 10 false *a 0.74,0.219 1.198,0.417 0.458,0.198 10 false CANP 2,0.229 2.458,0.427 0.458,0.198 10 false CANN
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G216-9 (CANP) - G216-10 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - NO. 4 CAN JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the G288 No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
C210060C76
0.323,0.917 0.802,1.167 0.479,0.25 0.948,0.521 1.115,0.521 1.115,0.521 1.344,0.896 true 2.188,0.406 2.01,0.406 2.01,0.406 1.677,0.917 true 0.521,0.438 0.958,0.615 0.438,0.177 10 false CANP 0.427,0.958 0.844,1.188 0.417,0.229 10 false G299 0.063,0.063 0.271,0.24 0.208,0.177 10 false *a 2.229,0.313 2.667,0.49 0.438,0.177 10 false CANN
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)


Disconnect the No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G299-3 (CANP) - G299-2 (CANN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR)
a.
C379604C41
0.104,1.281 0.604,1.521 0.5,0.24 0.25,3.479 0.75,3.719 0.5,0.24 2.406,4.333 2.24,4.333 2.24,4.333 2.24,3.833 true 0.708,0.594 0.875,0.594 0.875,0.594 0.875,1.344 true 1.469,4.26 1.635,4.26 1.635,4.26 1.635,3.51 true 0.865,0.427 1.031,0.427 1.031,0.427 1.031,1.344 true 1.042,0.271 1.208,0.271 1.208,0.271 1.208,1.354 true 1.552,0.104 1.385,0.104 1.385,0.104 1.385,1.354 true 1.719,0.271 1.552,0.271 1.552,0.271 1.552,1.354 true 1.906,0.438 1.74,0.438 1.74,0.438 1.74,1.354 true 2.063,0.604 1.896,0.604 1.896,0.604 1.896,1.354 true 0.708,2.135 0.875,2.135 0.875,2.135 0.875,1.719 true 0.865,2.323 1.031,2.323 1.031,2.323 1.031,1.708 true 1.031,2.5 1.198,2.5 1.198,2.5 1.198,1.719 true 1.219,2.698 1.385,2.698 1.385,2.698 1.385,1.708 true 1.719,2.625 1.552,2.625 1.552,2.625 1.552,1.708 true 1.875,2.385 1.708,2.385 1.708,2.385 1.708,1.719 true 2.052,2.135 1.885,2.135 1.885,2.135 1.885,1.719 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.115,2.781 0.427,2.979 0.313,0.198 10 false *b 0.198,1.302 0.583,1.5 0.385,0.198 10 false G288 0.365,3.51 0.75,3.708 0.385,0.198 10 false G48 2.458,4.24 2.844,4.438 0.385,0.198 10 false BAT 1.927,2.302 2.479,2.5 0.552,0.198 10 false CANL*h 2.115,0.531 2.667,0.729 0.552,0.198 10 false CANH*i 1.615,0 2.167,0.198 0.552,0.198 10 false CANH*f 0.177,0.51 0.729,0.708 0.552,0.198 10 false CANH*c 0.208,2.063 0.76,2.26 0.552,0.198 10 false CANL*c 0.365,2.24 0.917,2.438 0.552,0.198 10 false CANL*d 0.51,2.406 1.063,2.604 0.552,0.198 10 false CANL*e 1.76,2.573 2.313,2.771 0.552,0.198 10 false CANL*g 1.229,4.167 1.615,4.365 0.385,0.198 10 false CG 0.323,0.344 0.875,0.542 0.552,0.198 10 false CANH*d 0.479,0.167 1.031,0.365 0.552,0.198 10 false CANH*e 1.781,0.188 2.333,0.385 0.552,0.198 10 false CANH*g 1.938,0.375 2.49,0.573 0.552,0.198 10 false CANH*h 0.729,2.615 1.281,2.813 0.552,0.198 10 false CANL*f 2.115,2.063 2.667,2.26 0.552,0.198 10 false CANL*i
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3
*c to Outer Mirror Control ECU Assembly RH (w/ Reverse Shift-linked Mirror)
*d to Front Power Seat Switch (Power Seat Control ECU) (w/ Seat Memory)
*e to Multiplex Tilt and Telescopic ECU (for Power Tilt and Power Telescopic Steering Column)
*f to Main Body ECU (Multiplex Network Body ECU)
*g to Rear Television Camera Assembly (w/ Rear Television Camera Assembly [built-in ECU])
*h to Outer Mirror Control ECU Assembly LH (w/ Reverse Shift-linked Mirror)
*i to No. 2 CAN Junction Terminal


Disconnect the No. 4 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Seat Memory

*2: for Power Tilt and Power Telescopic Steering Column

*3: w/ Rear Television Camera Assembly (built-in ECU)

*4: w/ Reverse Shift-linked Mirror

G288-1 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly RH*4
G288-12 (CANL) - G48-4 (CG)
G288-1 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G288-12 (CANL) - G48-16 (BAT)
G288-2 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Front power seat switch (power seat control ECU)*1
G288-13 (CANL) - G48-4 (CG)
G288-2 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G288-13 (CANL) - G48-16 (BAT)
G288-3 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Multiplex tilt and telescopic ECU*2
G288-14 (CANL) - G48-4 (CG)
G288-3 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G288-14 (CANL) - G48-16 (BAT)
G288-4 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
G288-15 (CANL) - G48-4 (CG)
G288-4 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G288-15 (CANL) - G48-16 (BAT)
G288-5 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rear television camera assembly*3
G288-16 (CANL) - G48-4 (CG)
G288-5 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G288-16 (CANL) - G48-16 (BAT)
G288-6 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Outer mirror control ECU assembly LH*4
G288-17 (CANL) - G48-4 (CG)
G288-6 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G288-17 (CANL) - G48-16 (BAT)
G288-7 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN junction terminal
G288-18 (CANL) - G48-4 (CG)
G288-7 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G288-18 (CANL) - G48-16 (BAT)


Result:
Result Proceed to
OK A
NG (No. 2 CAN junction terminal CAN main wire) B
NG (Wire to ECU or sensor) C




A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

14.CONNECT CONNECTOR

C

16.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
14.CONNECT CONNECTOR
a.

Reconnect the G288 No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
C251147C12
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.927,0.25 1.448,0.427 0.521,0.177 10 false CANN 0.594,1.125 1.042,1.375 0.448,0.25 10 false CANP 2.5,0.771 2.948,1.021 0.448,0.25 10 false G299 0.531,2.563 0.979,2.813 0.448,0.25 10 false G48 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G299-3 (CANP) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G299-2 (CANN) - G48-4 (CG)
G299-3 (CANP) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G299-2 (CANN) - G48-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.

Reconnect the wire harness connectors.


b.
C251147C12
2.438,0.708 2.854,0.969 0.417,0.26 0.469,2.51 0.885,2.771 0.417,0.26 1.052,1.188 1.198,1.188 1.198,1.188 1.396,0.906 true 1.333,0.313 1.479,0.313 1.479,0.313 1.677,0.729 true 2.438,3.083 2.323,3.083 2.323,3.083 2.198,2.844 true 1.302,2.104 1.479,2.104 1.479,2.104 1.667,2.438 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.094,1.969 0.406,2.125 0.313,0.156 10 false *b 0.927,0.25 1.448,0.427 0.521,0.177 10 false CANN 0.594,1.125 1.042,1.375 0.448,0.25 10 false CANP 2.5,0.771 2.948,1.021 0.448,0.25 10 false G299 0.531,2.563 0.979,2.813 0.448,0.25 10 false G48 1.052,2.031 1.5,2.281 0.448,0.25 10 false CG 2.479,3.01 2.927,3.26 0.448,0.25 10 false BAT
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited main/branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G299-3 (CANP) - G299-2 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G299-3 (CANP) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G299-2 (CANN) - G48-4 (CG)
G299-3 (CANP) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G299-2 (CANN) - G48-16 (BAT)


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short to CAN bus lines in the ECU or sensor.

·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short to B+ in the ECU or sensor.

·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short to GND in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short circuit in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR