Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Any of the following conditions are met:
·

"Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Master cylinder solenoid (skid control ECU) CAN branch wire or connector

·

Power source circuit of master cylinder solenoid (skid control ECU)

·

Master cylinder solenoid (skid control ECU) ground circuit

·

Master cylinder solenoid (skid control ECU)



WIRING DIAGRAM

C217310E21
5.823,1.146 6.333,1.344 0.51,0.198 10 false +BM1 5.823,1.479 6.281,1.688 0.458,0.208 10 false +BM2 5.823,2.583 6.323,2.802 0.5,0.219 10 false GND1 5.823,3.292 6.323,3.5 0.5,0.208 10 false GND3 4.49,0.99 5.219,1.156 0.729,0.167 10 false ABS NO. 1 4.49,1.719 5.219,1.885 0.729,0.167 10 false ABS NO. 2 4.667,2.073 4.958,2.229 0.292,0.156 10 false IGN 2.948,1.104 3.76,1.313 0.813,0.208 10 false from Battery 0.406,1.104 0.958,1.281 0.552,0.177 10 false G286 1.76,0.26 2.125,0.552 0.365,0.292 10 false 10 1.771,0.625 2.104,0.885 0.333,0.26 10 false 20 0.417,1.25 2.375,1.667 1.958,0.417 10 false No. 2 CAN Junction Connector 2.792,2.198 3.781,2.427 0.99,0.229 10 false from IG2 Relay 5.51,1.135 5.771,1.302 0.26,0.167 10 false A7 5.51,1.49 5.771,1.656 0.26,0.167 10 false A8 5.51,2.583 5.771,2.729 0.26,0.146 10 false A7 5.51,3.292 5.771,3.448 0.26,0.156 10 false A8 5.573,0.938 5.677,1.094 0.104,0.156 10 false 2 5.823,2.24 6.219,2.438 0.396,0.198 10 false IG2 5.51,2.219 5.771,2.375 0.26,0.156 10 false A8 5.563,2.031 5.677,2.188 0.115,0.156 10 false 1 5.573,1.302 5.688,1.469 0.115,0.167 10 false 2 5.823,1.865 6.26,2.063 0.438,0.198 10 false +BS 5.51,1.865 5.771,2.031 0.26,0.167 10 false A7 5.531,1.667 5.708,1.833 0.177,0.167 10 false 31 5.823,0.406 6.25,0.552 0.427,0.146 10 false CANH 5.823,0.75 6.219,0.917 0.396,0.167 10 false CANL 5.51,0.385 5.76,0.542 0.25,0.156 10 false A7 5.51,0.74 5.771,0.896 0.26,0.156 10 false A7 5.51,0.208 5.708,0.365 0.198,0.156 10 false 11 5.51,0.573 5.708,0.74 0.198,0.167 10 false 25 5.563,2.385 5.667,2.552 0.104,0.167 10 false 1 5.823,2.938 6.385,3.198 0.563,0.26 10 false GND2 5.51,2.927 5.771,3.083 0.26,0.156 10 false A7 5.531,2.75 5.74,2.927 0.208,0.177 10 false 32 5.563,3.104 5.667,3.26 0.104,0.156 10 false 4 5.375,3.802 7.01,4.188 1.635,0.385 10 false Master Cylinder Solenoid (Skid Control ECU)

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MASTER CYLINDER SOLENOID [SKID CONTROL ECU] BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U115863C01
2.198,1.771 2.354,0.906 2.354,0.906 2.458,0.906 true 2.208,1.896 2.76,1.167 2.76,1.167 2.844,1.167 true 0.073,0.083 0.271,0.271 0.198,0.188 10 false *a 1.594,0.667 1.875,0.854 0.281,0.188 10 false A7 2.5,0.823 3.042,1.01 0.542,0.188 10 false CANH 2.885,1.083 3.406,1.323 0.521,0.24 10 false CANL
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


Disconnect the master cylinder solenoid (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U148344C01
1.01,0.385 0.885,0.385 0.885,0.385 0.76,1.302 false 1.417,0.646 1.292,0.646 1.292,0.646 1.052,1.292 false 2.198,2.813 2.083,2.813 2.083,2.813 1.875,3.365 false 1,2.625 0.885,2.625 0.885,2.625 0.76,1.708 false 1.063,2.948 1.177,2.948 1.177,2.948 1.573,3.417 false 1.396,2.396 1.292,2.396 1.292,2.396 1.052,1.729 false 2.365,4.104 2.26,4.104 2.26,4.104 1.938,3.74 false 0.031,0.042 0.313,0.271 0.281,0.229 10 false *a 1.042,0.313 1.458,0.49 0.417,0.177 10 false GND1 1.031,2.542 1.333,2.719 0.302,0.177 10 false +BS 0.802,2.875 1.073,3.052 0.271,0.177 10 false IG2 0.688,3.49 0.958,3.667 0.271,0.177 10 false A8 1.438,0.573 1.844,0.75 0.406,0.177 10 false +BM1 2.24,2.729 2.646,2.906 0.406,0.177 10 false +BM2 1.417,2.323 1.823,2.5 0.406,0.177 10 false GND2 2.385,4 2.792,4.177 0.406,0.177 10 false GND3 1.823,0.292 2.094,0.469 0.271,0.177 10 false A7
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


Disconnect the master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A7-32 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A8-4 (GND3) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-2 (+BM1) - Body ground Always 11 to 14 V
A8-2 (+BM2) - Body ground Always 11 to 14 V
A7-31 (+BS) - Body ground Always 11 to 14 V
A8-1 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)