Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 5 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area

*1: w/ Parking Assist Monitor System

*2: w/ Pre-crash Safety System

*3: w/ TOYOTA Parking Assist-sensor System (w/ Multi-display)

*4: w/ Kinetic Dynamic Suspension System

*5: w/ Pre-crash Safety System

*6: w/ Blind Spot Monitor System

*7: w/ Air Suspension System

There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to GND in CAN main bus line

·

Short to GND in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Parking assist ECU*1

·

Driving support ECU assembly*2

·

Clearance warning ECU assembly*3

·

Stabilizer control ECU*4

·

Forward recognition camera*5

·

Blind spot monitor sensor LH*6

·

Millimeter wave radar sensor assembly*2

·

Suspension control ECU*7

·

No. 1 CAN junction terminal

·

No. 1 CAN junction connector

·

No. 3 CAN Junction connector

·

No. 7 CAN Junction connector



WIRING DIAGRAM

for LHD:


C382801E01
0.104,1.208 0.719,1.406 0.615,0.198 10 false G224 0.104,1.396 2.292,1.792 2.188,0.396 10 false Driving Support ECU Assembly*1 0.885,0.646 1.5,0.844 0.615,0.198 10 false CA2H 0.906,1.031 1.521,1.229 0.615,0.198 10 false CA2L 1.344,0.531 1.958,0.729 0.615,0.198 10 false 10 1.344,0.896 1.958,1.094 0.615,0.198 10 false 11 3.208,0.552 3.823,0.75 0.615,0.198 10 false 4 3.146,0.917 3.76,1.115 0.615,0.198 10 false 14 3.927,0.542 4.542,0.74 0.615,0.198 10 false 2 3.896,0.927 4.51,1.125 0.615,0.198 10 false 12 5.625,0.542 6.24,0.74 0.615,0.198 10 false 15 5.615,0.927 6.229,1.125 0.615,0.198 10 false 16 5.948,0.552 6.563,0.75 0.615,0.198 10 false CA5H 5.979,1.167 6.594,1.365 0.615,0.198 10 false CA5L 5.135,1.313 5.75,1.51 0.615,0.198 10 false G229 5.156,1.458 7.104,1.865 1.948,0.406 10 false Central Gateway ECU (Network Gateway ECU) 3.896,2.458 4.51,2.656 0.615,0.198 10 false 3 3.906,2.833 4.521,3.031 0.615,0.198 10 false 13 5.479,3.146 6.094,3.344 0.615,0.198 10 false I7 5.469,3.333 6.896,3.552 1.427,0.219 10 false Parking Assist ECU*5 3.896,3.469 4.51,3.667 0.615,0.198 10 false G291 3.906,3.635 5.188,4.021 1.281,0.385 10 false No. 7 CAN Junction Connector 3.156,2.417 3.771,2.615 0.615,0.198 10 false 5 3.104,2.875 3.719,3.073 0.615,0.198 10 false 15 5.667,2.875 6.281,3.073 0.615,0.198 10 false 39 5.688,2.5 6.302,2.698 0.615,0.198 10 false 40 5.917,2.594 6.531,2.792 0.615,0.198 10 false CANH 5.948,2.99 6.563,3.188 0.615,0.198 10 false CANL 0.125,3.313 1.365,3.594 1.24,0.281 10 false I9*3, G228*4 0.135,3.458 2.479,3.885 2.344,0.427 10 false Clearance Warning ECU Assembly*2 3.198,3.396 3.813,3.594 0.615,0.198 10 false 1 3.135,3.667 3.75,3.865 0.615,0.198 10 false 11 3.198,4.646 3.813,4.844 0.615,0.198 10 false 1 3.135,5.094 3.75,5.292 0.615,0.198 10 false 11 3.906,4.667 4.521,4.865 0.615,0.198 10 false 2 3.896,5.073 4.51,5.271 0.615,0.198 10 false 12 1.063,2.594 1.677,2.792 0.615,0.198 10 false R1 1.073,2.958 1.688,3.156 0.615,0.198 10 false R2 1.365,2.479 1.979,2.677 0.615,0.198 10 false 17 1.375,2.854 1.99,3.052 0.615,0.198 10 false 18 5.927,4.802 6.542,5 0.615,0.198 10 false CANH 5.948,5.208 6.563,5.406 0.615,0.198 10 false CANL 5.677,4.656 6.292,4.854 0.615,0.198 10 false 29 5.677,5.063 6.292,5.26 0.615,0.198 10 false 28 5.479,5.375 6.094,5.573 0.615,0.198 10 false G123 5.479,5.521 7.094,5.792 1.615,0.271 10 false Stabilizer Control ECU*6 3.917,6.594 4.531,6.792 0.615,0.198 10 false 3 3.896,7 4.51,7.198 0.615,0.198 10 false 13 5.49,7.292 6.104,7.49 0.615,0.198 10 false W22 5.531,7.51 6.792,7.854 1.26,0.344 10 false Forward Recognition Camera*1 5.927,6.719 6.542,6.917 0.615,0.198 10 false CA1P 5.948,7.094 6.563,7.292 0.615,0.198 10 false CA1N 5.677,7 6.292,7.198 0.615,0.198 10 false 11 5.729,6.625 6.344,6.823 0.615,0.198 10 false 5 3.188,6.594 3.802,6.792 0.615,0.198 10 false 9 3.135,6.99 3.75,7.188 0.615,0.198 10 false 19 0.115,7.417 0.729,7.615 0.615,0.198 10 false R42 0.115,7.604 2.188,7.99 2.073,0.385 10 false Blind Spot Monitor Sensor LH*7 0.896,6.74 1.51,6.938 0.615,0.198 10 false CA1P 0.885,7.125 1.5,7.323 0.615,0.198 10 false CA1N 1.365,6.604 1.979,6.802 0.615,0.198 10 false 2 1.365,6.979 1.979,7.177 0.615,0.198 10 false 7 3.094,8.229 3.708,8.427 0.615,0.198 10 false G287 3.104,8.406 5.01,8.76 1.906,0.354 10 false No. 3 CAN Junction Connector 0.083,3.958 2.063,4.271 1.979,0.313 10 false *1: w/ Pre-crash Safety System 0.104,4.26 2.49,4.656 2.385,0.396 10 false *2: w/ TOYOTA Parking Assist-sensor System (w/ Multi-display) 0.094,4.823 2.479,5.219 2.385,0.396 10 false *3: for 4 Sensor Type 0.083,5.146 2.469,5.542 2.385,0.396 10 false *4: for 8 Sensor Type 0.083,5.479 2.469,5.875 2.385,0.396 10 false *5: w/ Parking Assist Monitor System 0.094,5.833 3.063,6.135 2.969,0.302 10 false *6: w/ Kinetic Dynamic Suspension System 0.094,6.188 3.063,6.49 2.969,0.302 10 false *7: w/ Blind Spot Monitor System 3.135,7.844 3.75,8.042 0.615,0.198 10 false 20 3.156,7.49 3.771,7.688 0.615,0.198 10 false 10

C402012E01
2.781,3.635 3.396,3.833 0.615,0.198 10 false A121 2.771,3.802 4.729,4.125 1.958,0.323 10 false No. 1 CAN Junction Connector 0.125,1.906 0.74,2.104 0.615,0.198 10 false A100 0.125,2.094 1.583,2.479 1.458,0.385 10 false Millimeter Wave Radar Sensor Assembly*2 0.865,1.323 1.479,1.521 0.615,0.198 10 false CA2H 0.875,1.708 1.49,1.906 0.615,0.198 10 false CA2L 1.365,1.198 1.979,1.396 0.615,0.198 10 false 3 1.375,1.594 1.99,1.792 0.615,0.198 10 false 2 3.198,1.208 3.813,1.406 0.615,0.198 10 false 2 3.198,1.563 3.813,1.76 0.615,0.198 10 false 8 3.156,0.719 3.771,0.917 0.615,0.198 10 false 11 3.198,0.313 3.813,0.51 0.615,0.198 10 false 5 3.906,1.208 4.521,1.406 0.615,0.198 10 false 1 3.917,1.583 4.531,1.781 0.615,0.198 10 false 7 5.302,1.875 5.917,2.073 0.615,0.198 10 false A49 5.323,2.052 7.021,2.417 1.698,0.365 10 false Suspension Control ECU*1 5.74,1.208 6.354,1.406 0.615,0.198 10 false 7 5.729,1.563 6.344,1.76 0.615,0.198 10 false 8 5.927,1.313 6.542,1.51 0.615,0.198 10 false CANH 5.938,1.698 6.552,1.896 0.615,0.198 10 false CANL 3.906,3.302 4.521,3.5 0.615,0.198 10 false 10 3.948,2.917 4.563,3.115 0.615,0.198 10 false 4 5.271,3.667 5.885,3.865 0.615,0.198 10 false G298 5.302,3.823 7.104,4.26 1.802,0.438 10 false No. 1 CAN Junction Terminal 5.927,2.927 6.542,3.125 0.615,0.198 10 false CANH 5.969,3.563 6.583,3.76 0.615,0.198 10 false CANL 5.719,2.927 6.333,3.125 0.615,0.198 10 false 3 5.719,3.354 6.333,3.552 0.615,0.198 10 false 2 0.135,3.531 2.208,3.802 2.073,0.271 10 false *1: w/ Air Suspension System 0.167,3.875 2.24,4.146 2.073,0.271 10 false *2: w/ Pre-crash Safety System


for RHD:


C382803E01
2.906,2.813 3.521,3.01 0.615,0.198 10 false A121 2.906,2.969 4.792,3.229 1.885,0.26 10 false No. 1 CAN Junction Connector 3.115,2.521 3.729,2.719 0.615,0.198 10 false 10 3.177,2.115 3.792,2.313 0.615,0.198 10 false 4 3.896,2.521 4.51,2.719 0.615,0.198 10 false 8 3.896,2.094 4.51,2.292 0.615,0.198 10 false 2 5.375,2.792 5.99,2.99 0.615,0.198 10 false A100 5.375,2.948 6.823,3.354 1.448,0.406 10 false Millimeter Wave Radar Sensor Assembly*2 5.938,2.635 6.552,2.833 0.615,0.198 10 false CA2L 5.927,2.229 6.542,2.427 0.615,0.198 10 false CA2H 5.729,2.125 6.344,2.323 0.615,0.198 10 false 3 5.74,2.521 6.354,2.719 0.615,0.198 10 false 2 3.917,0.677 4.531,0.875 0.615,0.198 10 false 11 3.958,0.292 4.573,0.49 0.615,0.198 10 false 5 5.083,1.104 5.698,1.302 0.615,0.198 10 false G229 5.083,1.26 7.063,1.677 1.979,0.417 10 false Central Gateway ECU (Network Gateway ECU) 5.938,0.302 6.552,0.5 0.615,0.198 10 false CA5H 5.927,0.927 6.542,1.125 0.615,0.198 10 false CA5L 5.667,0.688 6.281,0.885 0.615,0.198 10 false 16 5.667,0.302 6.281,0.5 0.615,0.198 10 false 15 3.198,0.313 3.813,0.51 0.615,0.198 10 false 1 3.198,0.677 3.813,0.875 0.615,0.198 10 false 7 0.177,0.99 0.792,1.188 0.615,0.198 10 false A49 0.167,1.156 1.958,1.542 1.792,0.385 10 false Suspension Control ECU*1 0.833,0.417 1.448,0.615 0.615,0.198 10 false CANH 0.854,0.802 1.469,1 0.615,0.198 10 false CANL 1.365,0.313 1.979,0.51 0.615,0.198 10 false 7 1.365,0.688 1.979,0.885 0.615,0.198 10 false 8 3.104,4.167 3.719,4.365 0.615,0.198 10 false 13 3.156,3.75 3.771,3.948 0.615,0.198 10 false 3 3.917,3.781 4.531,3.979 0.615,0.198 10 false 4 3.906,4.156 4.521,4.354 0.615,0.198 10 false 14 5.448,4.448 6.063,4.646 0.615,0.198 10 false G224 5.469,4.625 6.75,5.031 1.281,0.406 10 false Driving Support ECU Assembly*2 5.656,4.188 6.271,4.385 0.615,0.198 10 false 11 5.646,3.771 6.26,3.969 0.615,0.198 10 false 10 5.948,3.854 6.563,4.052 0.615,0.198 10 false CA2H 5.969,4.25 6.583,4.448 0.615,0.198 10 false CA2L 5.396,6.063 6.01,6.26 0.615,0.198 10 false W22 5.417,6.24 6.698,6.646 1.281,0.406 10 false Forward Recognition Camera*2 5.938,5.479 6.552,5.677 0.615,0.198 10 false CA1P 5.948,5.875 6.563,6.073 0.615,0.198 10 false CA1N 5.656,5.781 6.271,5.979 0.615,0.198 10 false 11 5.698,5.385 6.313,5.583 0.615,0.198 10 false 5 5.938,7.073 6.552,7.271 0.615,0.198 10 false R1 5.948,7.49 6.563,7.688 0.615,0.198 10 false R2 5.677,6.969 6.292,7.167 0.615,0.198 10 false 17 5.677,7.365 6.292,7.563 0.615,0.198 10 false 18 5.458,7.708 6.073,7.906 0.615,0.198 10 false G228 5.448,7.875 6.958,8.281 1.51,0.406 10 false Clearance Warning ECU Assembly*4 3.906,6.958 4.521,7.156 0.615,0.198 10 false 7 3.917,7.354 4.531,7.552 0.615,0.198 10 false 17 3.885,5.781 4.5,5.979 0.615,0.198 10 false 15 3.927,5.344 4.542,5.542 0.615,0.198 10 false 5 3.135,5.76 3.75,5.958 0.615,0.198 10 false 16 3.177,5.323 3.792,5.521 0.615,0.198 10 false 6 0.865,5.49 1.479,5.688 0.615,0.198 10 false CA1P 0.833,5.885 1.448,6.083 0.615,0.198 10 false CA1N 1.354,5.75 1.969,5.948 0.615,0.198 10 false 7 1.365,5.375 1.979,5.573 0.615,0.198 10 false 2 3.188,6.979 3.802,7.177 0.615,0.198 10 false 1 3.125,7.365 3.74,7.563 0.615,0.198 10 false 11 3.01,7.76 3.625,7.958 0.615,0.198 10 false G291 2.99,7.917 4.292,8.292 1.302,0.375 10 false No. 7 CAN Junction Connector 0.156,6.719 2.479,7.125 2.323,0.406 10 false *1: w/ Air Suspension System 0.125,7.031 2.448,7.438 2.323,0.406 10 false *2: w/ Pre-crash Safety System 0.104,7.385 2.427,7.792 2.323,0.406 10 false *3: w/ Blind Spot Monitor System 0.135,7.844 2.125,8.406 1.99,0.563 10 false *4: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type with Multi-display) 0.146,6.01 0.76,6.208 0.615,0.198 10 false R42 0.156,6.198 2.208,6.646 2.052,0.448 10 false Blind Spot Monitor Sensor LH*3

C402013E01
2.656,3.594 3.271,3.792 0.615,0.198 10 false G287 2.677,3.76 4.677,4.104 2,0.344 10 false No. 3 CAN Junction Connector 3.188,0.313 3.802,0.51 0.615,0.198 10 false 1 3.156,0.688 3.771,0.885 0.615,0.198 10 false 11 3.188,1.198 3.802,1.396 0.615,0.198 10 false 2 3.146,1.594 3.76,1.792 0.615,0.198 10 false 12 3.115,3.302 3.729,3.5 0.615,0.198 10 false 14 3.167,2.917 3.781,3.115 0.615,0.198 10 false 4 3.885,3.292 4.5,3.49 0.615,0.198 10 false 20 3.875,2.906 4.49,3.104 0.615,0.198 10 false 10 3.885,1.604 4.5,1.802 0.615,0.198 10 false 15 3.906,1.198 4.521,1.396 0.615,0.198 10 false 5 0.135,1.896 0.75,2.094 0.615,0.198 10 false G123 0.146,2.063 2.417,2.333 2.271,0.271 10 false Stabilizer Control ECU*1 0.844,1.313 1.458,1.51 0.615,0.198 10 false CANH 0.865,1.708 1.479,1.906 0.615,0.198 10 false CANL 1.396,1.583 2.01,1.781 0.615,0.198 10 false 28 1.396,1.219 2.01,1.417 0.615,0.198 10 false 29 0.135,3.583 0.75,3.781 0.615,0.198 10 false I7 0.125,3.76 2.396,4.031 2.271,0.271 10 false Parking Assist ECU*3 0.865,3.031 1.479,3.229 0.615,0.198 10 false CANH 0.844,3.458 1.458,3.656 0.615,0.198 10 false CANL 1.333,3.323 1.948,3.521 0.615,0.198 10 false 39 1.333,2.906 1.948,3.104 0.615,0.198 10 false 40 5.74,2.906 6.354,3.104 0.615,0.198 10 false 3 5.74,3.333 6.354,3.531 0.615,0.198 10 false 2 5.938,2.938 6.552,3.135 0.615,0.198 10 false CANH 5.938,3.563 6.552,3.76 0.615,0.198 10 false CANL 5.427,3.698 6.042,3.896 0.615,0.198 10 false G298 5.469,3.875 6.74,4.292 1.271,0.417 10 false No. 1 CAN Junction Terminal 5.563,1.906 6.177,2.104 0.615,0.198 10 false I9 5.563,2.073 6.833,2.448 1.271,0.375 10 false Clearance Warning ECU Assembly*2 5.938,1.313 6.552,1.51 0.615,0.198 10 false R1 5.927,1.729 6.542,1.927 0.615,0.198 10 false R2 5.646,1.615 6.26,1.813 0.615,0.198 10 false 18 5.646,1.198 6.26,1.396 0.615,0.198 10 false 17 0.135,4.146 3.094,4.49 2.958,0.344 10 false *1: w/ Kinetic Dynamic Suspension System 0.115,4.458 5.479,4.771 5.365,0.313 10 false *2: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type with Multi-display) 2.958,4.146 5.917,4.49 2.958,0.344 10 false *3: w/ Parking Assist Monitor System


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

B

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 3 CAN junction connector.

C382812C09
0.229,1.781 0.677,2.042 0.448,0.26 5.302,1.031 5.75,1.292 0.448,0.26 0.844,1.385 1.01,1.385 1.01,1.385 1.01,1.885 true 1.083,1.146 1.25,1.146 1.25,1.146 1.25,1.896 true 1.323,0.948 1.49,0.948 1.49,0.948 1.49,1.865 true 3.104,1.167 2.938,1.167 2.938,1.167 2.938,1.917 true 3.344,1.427 3.177,1.427 3.177,1.427 3.177,1.927 true 3.344,2.521 3.177,2.521 3.177,2.521 3.177,2.104 true 3.104,2.75 2.938,2.75 2.938,2.75 2.938,2.083 true 1.323,3.115 1.49,3.115 1.49,3.115 1.49,2.115 true 1.073,2.938 1.24,2.938 1.24,2.938 1.24,2.104 true 0.854,2.771 1.021,2.771 1.021,2.771 1.021,2.104 true 5.927,2.552 5.76,2.552 5.76,2.552 5.531,1.844 true 0.177,0.531 0.49,0.729 0.313,0.198 10 false *a 4.438,0.833 4.75,1.031 0.313,0.198 10 false *b 0.271,1.833 0.625,2.031 0.354,0.198 10 false G287 0.313,1.292 0.917,1.531 0.604,0.24 10 false CANH*c 0.542,1.063 1.146,1.302 0.604,0.24 10 false CANH*d 0.771,0.844 1.375,1.083 0.604,0.24 10 false CANH*e 3.167,1.083 3.771,1.323 0.604,0.24 10 false CANH*f 3.385,1.333 3.99,1.573 0.604,0.24 10 false CANH*g 0.344,2.688 0.948,2.927 0.604,0.24 10 false CANL*c 0.563,2.854 1.167,3.094 0.604,0.24 10 false CANL*d 0.813,3.031 1.417,3.271 0.604,0.24 10 false CANL*e 3.167,2.667 3.771,2.906 0.604,0.24 10 false CANL*f 3.396,2.427 4,2.667 0.604,0.24 10 false CANL*g 5.958,2.49 6.375,2.729 0.417,0.24 10 false CG 5.375,1.073 5.729,1.271 0.354,0.198 10 false G48
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b Front view of DLC3
*c to No. 7 CAN Junction Connector *d to Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System)
*e to Forward Recognition Camera (w/ Pre-crash Safety System) *f to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System)
*g to No. 1 CAN Junction Connector - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Kinetic Dynamic Suspension System

*2: w/ Pre-crash Safety System

*3: w/ Blind Spot Monitor System

G287-1 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 7 CAN junction connector
G287-11 (CANL) - G48-4 (CG)
G287-2 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Stabilizer control ECU*1
G287-12 (CANL) - G48-4 (CG)
G287-3 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward recognition camera*2
G287-13 (CANL) - G48-4 (CG)
G287-9 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Blind spot monitor sensor LH*3
G287-19 (CANL) - G48-4 (CG)
G287-10 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
G287-20 (CANL) - G48-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (No. 7 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

3.CONNECT CONNECTOR

C

5.CONNECT CONNECTOR

D

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
3.CONNECT CONNECTOR
a.

Reconnect the G287 No. 3 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.
C382815C03
0.198,0.813 0.625,1.042 0.427,0.229 0.177,2.302 0.604,2.531 0.427,0.229 0.656,0.49 0.823,0.49 0.823,0.49 0.958,0.875 true 0.844,0.281 1.01,0.281 1.01,0.281 1.25,0.854 true 2.188,0.073 2.021,0.073 2.021,0.073 1.844,0.875 true 2.406,0.281 2.24,0.281 2.24,0.281 2.135,0.875 true 2.531,1.646 2.365,1.646 2.365,1.646 2.135,1.031 true 2.229,1.833 2.063,1.833 2.063,1.833 1.844,1.052 true 0.906,1.583 1.073,1.583 1.073,1.583 1.26,1.052 true 0.604,1.344 0.771,1.344 0.771,1.344 0.979,1.021 true 2.01,3.031 1.844,3.031 1.844,3.031 1.625,2.385 true 0.25,0.854 0.865,1.052 0.615,0.198 10 false A121 0.24,2.333 0.854,2.531 0.615,0.198 10 false G48 0.073,0.063 0.688,0.26 0.615,0.198 10 false *a 0.146,1.885 0.76,2.083 0.615,0.198 10 false *b 0.094,0.427 0.708,0.625 0.615,0.198 10 false CANH*c 0.313,0.219 0.927,0.417 0.615,0.198 10 false CANH*d 2.24,0.021 2.854,0.219 0.615,0.198 10 false CANH*e 2.458,0.198 3.073,0.396 0.615,0.198 10 false CANH*f 2.583,1.573 3.198,1.771 0.615,0.198 10 false CANL*f 2.271,1.771 2.885,1.969 0.615,0.198 10 false CANL*e 0.385,1.51 1,1.708 0.615,0.198 10 false CANL*d 0.094,1.271 0.708,1.469 0.615,0.198 10 false CANL*c 2.083,2.948 2.698,3.146 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3
*c to Suspension Control ECU (w/ Air Suspension System)
*d to Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System)
*e to No. 1 CAN Junction Terminal
*f to No. 3 CAN Junction Connector


Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Air Suspension System

*2: w/ Pre-crash Safety System

A121-1 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Suspension control ECU*1
A121-7 (CANL) - G48-4 (CG)
A121-2 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*2
A121-8 (CANL) - G48-4 (CG)
A121-4 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction terminal
A121-10 (CANL) - G48-4 (CG)
A121-5 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 3 CAN junction connector
A121-11 (CANL) - G48-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR- NO. 3 CAN JUNCTION CONNECTOR)

C

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
5.CONNECT CONNECTOR
a.

Reconnect the G287 No. 3 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 7 CAN junction connector.

C382812C10
0.229,1.781 0.677,2.042 0.448,0.26 5.302,1.031 5.75,1.292 0.448,0.26 0.844,1.385 1.01,1.385 1.01,1.385 1.01,1.885 true 1.083,1.146 1.25,1.146 1.25,1.146 1.25,1.896 true 1.323,0.948 1.49,0.948 1.49,0.948 1.49,1.865 true 1.896,1.146 1.729,1.146 1.729,1.146 1.729,1.896 true 2.135,1.427 1.969,1.427 1.969,1.427 1.969,1.927 true 2.125,2.521 1.958,2.521 1.958,2.521 1.958,2.104 true 1.906,2.76 1.74,2.76 1.74,2.76 1.74,2.094 true 1.323,3.115 1.49,3.115 1.49,3.115 1.49,2.115 true 1.073,2.938 1.24,2.938 1.24,2.938 1.24,2.104 true 0.854,2.771 1.021,2.771 1.021,2.771 1.021,2.104 true 6.073,2.531 5.906,2.531 5.906,2.531 5.531,1.844 true 0.177,0.531 0.49,0.729 0.313,0.198 10 false *a 4.438,0.833 4.75,1.031 0.313,0.198 10 false *b 0.271,1.833 0.625,2.031 0.354,0.198 10 false G291 0.313,1.292 0.917,1.531 0.604,0.24 10 false CANH*c 0.542,1.063 1.146,1.302 0.604,0.24 10 false CANH*d 0.771,0.844 1.375,1.083 0.604,0.24 10 false CANH*e 1.948,1.073 2.552,1.313 0.604,0.24 10 false CANH*f 2.188,1.365 2.792,1.604 0.604,0.24 10 false CANH*g 0.344,2.688 0.948,2.927 0.604,0.24 10 false CANL*c 0.563,2.854 1.167,3.094 0.604,0.24 10 false CANL*d 0.813,3.031 1.417,3.271 0.604,0.24 10 false CANL*e 1.969,2.708 2.573,2.948 0.604,0.24 10 false CANL*f 2.188,2.458 2.792,2.698 0.604,0.24 10 false CANL*g 6.167,2.448 6.583,2.688 0.417,0.24 10 false CG 5.375,1.073 5.729,1.271 0.354,0.198 10 false G48
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to No. 3 CAN Junction Connector *d to Central Gateway ECU (Network Gateway ECU)
*e to Parking Assist ECU (w/ Parking Assist Monitor System) *f to Driving Support ECU Assembly (w/ Pre-crash Safety System)
*g to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [w/ Multi-display]) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Parking Assist Monitor System

*2: w/ Pre-crash Safety System

*3: w/ TOYOTA Parking Assist-sensor System (w/ Multi-display)

G291-1 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 3 CAN junction connector
G291-11 (CANL) - G48-4 (CG)
G291-2 (CANH)- G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G291-12 (CANL) - G48-4 (CG)
G291-3 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Parking assist ECU*1
G291-13 (CANL) - G48-4 (CG)
G291-4 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving support ECU assembly*2
G291-14 (CANL) - G48-4 (CG)
G291-5 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*3
G291-15 (CANL) - G48-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (Central gateway ECU [network gateway ECU] CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR- NO. 3 CAN JUNCTION CONNECTOR)

C

7.CONNECT CONNECTOR

D

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
7.CONNECT CONNECTOR
a.

Reconnect the G291 No. 7 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
a.
C324418C98
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.26,4.208 2.094,4.208 2.094,4.208 1.594,3.333 true 1.167,2.167 1.333,2.167 1.333,2.167 1.396,1.521 true 1.823,2.167 1.656,2.167 1.656,2.167 1.542,1.521 true 1.542,0.281 2.156,0.479 0.615,0.198 10 false G229 1.521,2.573 2.135,2.771 0.615,0.198 10 false G48 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 0.76,2.094 1.229,2.406 0.469,0.313 10 false CA5H 2.333,4.135 2.948,4.333 0.615,0.198 10 false CG 1.854,2.083 2.292,2.281 0.438,0.198 10 false CA5L
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-15 (CA5H) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-16 (CA5L) - G48-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)

9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 7 CAN junction connector.

C382812C11
0.229,1.781 0.677,2.042 0.448,0.26 5.302,1.031 5.75,1.292 0.448,0.26 0.844,1.385 1.01,1.385 1.01,1.385 1.01,1.885 true 1.323,1.167 1.49,1.167 1.49,1.167 1.49,1.917 true 1.563,0.969 1.729,0.969 1.729,0.969 1.729,1.885 true 2.385,1.167 2.219,1.167 2.219,1.167 2.219,1.917 true 2.854,1.438 2.688,1.438 2.688,1.438 2.469,1.896 true 2.906,2.583 2.74,2.583 2.74,2.583 2.469,2.104 true 2.385,2.833 2.219,2.833 2.219,2.833 2.219,2.083 true 1.323,3.115 1.49,3.115 1.49,3.115 1.49,2.115 true 0.854,2.771 1.021,2.771 1.021,2.771 1.021,2.104 true 5.896,2.552 5.729,2.552 5.729,2.552 5.552,1.844 true 1.792,0.813 1.958,0.813 1.958,0.813 1.958,1.896 true 1.552,3.365 1.719,3.365 1.719,3.365 1.719,2.115 true 1.813,3.51 1.979,3.51 1.979,3.51 1.979,2.073 true 0.177,0.531 0.49,0.729 0.313,0.198 10 false *a 4.438,0.833 4.75,1.031 0.313,0.198 10 false *b 0.271,1.833 0.625,2.031 0.354,0.198 10 false G291 0.313,1.292 0.917,1.531 0.604,0.24 10 false CANH*c 0.771,1.083 1.375,1.323 0.604,0.24 10 false CANH*d 1.031,0.885 1.635,1.125 0.604,0.24 10 false CANH*e 2.438,1.094 3.042,1.333 0.604,0.24 10 false CANH*g 2.896,1.354 3.5,1.594 0.604,0.24 10 false CANH*h 0.344,2.688 0.948,2.927 0.604,0.24 10 false CANL*c 0.792,3.031 1.396,3.271 0.604,0.24 10 false CANL*d 1.031,3.271 1.635,3.51 0.604,0.24 10 false CANL*e 1.333,3.448 1.938,3.688 0.604,0.24 10 false CANL*f 2.417,2.75 3.021,2.99 0.604,0.24 10 false CANL*g 5.969,2.479 6.385,2.719 0.417,0.24 10 false CG 5.375,1.073 5.729,1.271 0.354,0.198 10 false G48 1.271,0.75 1.875,0.99 0.604,0.24 10 false CANH*f 2.948,2.51 3.552,2.75 0.604,0.24 10 false CANL*h
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to No. 3 CAN Junction Connector *d to No. 1 CAN Junction Connector
*e to Driving Support ECU Assembly (w/ Pre-crash Safety System) *f to Forward Recognition Camera (w/ Pre-crash Safety System)
*g to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) *h to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type with Multi-display])



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Pre-crash Safety System

*2: w/ Blind Spot Monitor System

*3: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type with Multi-display)

G291-1 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 3 CAN junction connector
G291-11 (CANL) - G48-4 (CG)
G291-3 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector
G291-13 (CANL) - G48-4 (CG)
G291-4 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Driving support ECU assembly*1
G291-14 (CANL) - G48-4 (CG)
G291-5 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Forward recognition camera*1
G291-15 (CANL) - G48-4 (CG)
G291-6 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Blind spot monitor sensor LH*2
G291-16 (CANL) - G48-4 (CG)
G291-7 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*3
G291-17 (CANL) - G48-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (No. 3 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 7 CAN JUNCTION CONNECTOR

B

10.CONNECT CONNECTOR

C

14.CONNECT CONNECTOR

D

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
10.CONNECT CONNECTOR
a.

Reconnect the G291 No. 7 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.
C382815C04
0.198,0.813 0.625,1.042 0.427,0.229 0.177,2.302 0.604,2.531 0.427,0.229 0.656,0.49 0.823,0.49 0.823,0.49 0.958,0.875 true 0.844,0.281 1.01,0.281 1.01,0.281 1.25,0.854 true 2.188,0.073 2.021,0.073 2.021,0.073 1.844,0.875 true 2.406,0.281 2.24,0.281 2.24,0.281 2.135,0.875 true 2.531,1.646 2.365,1.646 2.365,1.646 2.135,1.031 true 2.229,1.833 2.063,1.833 2.063,1.833 1.844,1.052 true 0.906,1.583 1.073,1.583 1.073,1.583 1.26,1.052 true 0.604,1.344 0.771,1.344 0.771,1.344 0.979,1.021 true 2.156,3.042 1.99,3.042 1.99,3.042 1.635,2.365 true 0.25,0.854 0.865,1.052 0.615,0.198 10 false A121 0.24,2.333 0.854,2.531 0.615,0.198 10 false G48 0.073,0.063 0.688,0.26 0.615,0.198 10 false *a 0.146,1.885 0.76,2.083 0.615,0.198 10 false *b 0.094,0.427 0.708,0.625 0.615,0.198 10 false CANH*c 0.313,0.219 0.927,0.417 0.615,0.198 10 false CANH*d 2.24,0.021 2.854,0.219 0.615,0.198 10 false CANH*e 2.458,0.198 3.073,0.396 0.615,0.198 10 false CANH*f 2.583,1.573 3.198,1.771 0.615,0.198 10 false CANL*f 2.271,1.771 2.885,1.969 0.615,0.198 10 false CANL*e 0.385,1.51 1,1.708 0.615,0.198 10 false CANL*d 0.094,1.271 0.708,1.469 0.615,0.198 10 false CANL*c 2.24,2.969 2.854,3.167 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b Front view of DLC3
*c to Suspension Control ECU (w/ Air Suspension System)
*d to Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System)
*e to No. 7 CAN Junction Connector
*f to Central Gateway ECU (Network Gateway ECU)


Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Air Suspension System

*2: w/ Pre-crash Safety System

A121-1 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Suspension control ECU*1
A121-7 (CANL) - G48-4 (CG)
A121-2 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Millimeter wave radar sensor assembly*2
A121-8 (CANL) - G48-4 (CG)
A121-4 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 7 CAN junction connector
A121-10 (CANL) - G48-4 (CG)
A121-5 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
A121-11 (CANL) - G48-4 (CG)



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN main wire) B
NG (No. 7 CAN junction terminal CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

12.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR- NO. 7 CAN JUNCTION CONNECTOR)

D

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
12.CONNECT CONNECTOR
a.

Reconnect the A121 No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 1 CAN JUNCTION CONNECTOR)
13.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 1 CAN JUNCTION CONNECTOR)
a.
C324418C98
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.26,4.208 2.094,4.208 2.094,4.208 1.594,3.333 true 1.167,2.167 1.333,2.167 1.333,2.167 1.396,1.521 true 1.823,2.167 1.656,2.167 1.656,2.167 1.542,1.521 true 1.542,0.281 2.156,0.479 0.615,0.198 10 false G229 1.521,2.573 2.135,2.771 0.615,0.198 10 false G48 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 0.76,2.094 1.229,2.406 0.469,0.313 10 false CA5H 2.333,4.135 2.948,4.333 0.615,0.198 10 false CG 1.854,2.083 2.292,2.281 0.438,0.198 10 false CA5L
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-15 (CA5H) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-16 (CA5L) - G48-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 1 CAN JUNCTION CONNECTOR)

14.CONNECT CONNECTOR
a.

Reconnect the G291 No. 7 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
15.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 3 CAN junction connector.

C382812C12
0.229,1.781 0.677,2.042 0.448,0.26 5.302,1.031 5.75,1.292 0.448,0.26 0.844,1.385 1.01,1.385 1.01,1.385 1.01,1.885 true 1.083,1.167 1.25,1.167 1.25,1.167 1.25,1.917 true 1.563,0.969 1.729,0.969 1.729,0.969 1.729,1.885 true 3.49,1.438 3.323,1.438 3.323,1.438 3.188,1.906 true 3.469,2.583 3.302,2.583 3.302,2.583 3.156,2.073 true 1.073,3.115 1.24,3.115 1.24,3.115 1.24,2.115 true 0.854,2.771 1.021,2.771 1.021,2.771 1.021,2.104 true 5.854,2.552 5.688,2.552 5.688,2.552 5.531,1.813 true 1.792,0.813 1.958,0.813 1.958,0.813 1.958,1.896 true 1.552,3.365 1.719,3.365 1.719,3.365 1.719,2.115 true 1.813,3.51 1.979,3.51 1.979,3.51 1.979,2.073 true 0.177,0.531 0.49,0.729 0.313,0.198 10 false *a 4.438,0.833 4.75,1.031 0.313,0.198 10 false *b 0.271,1.833 0.625,2.031 0.354,0.198 10 false G287 0.313,1.292 0.917,1.531 0.604,0.24 10 false CANH*c 0.531,1.083 1.135,1.323 0.604,0.24 10 false CANH*d 1.031,0.885 1.635,1.125 0.604,0.24 10 false CANH*e 3.542,1.375 4.146,1.615 0.604,0.24 10 false CANH*g 0.344,2.688 0.948,2.927 0.604,0.24 10 false CANL*c 0.542,3.031 1.146,3.271 0.604,0.24 10 false CANL*d 1.031,3.271 1.635,3.51 0.604,0.24 10 false CANL*e 1.333,3.448 1.938,3.688 0.604,0.24 10 false CANL*f 5.906,2.479 6.323,2.719 0.417,0.24 10 false CG 5.375,1.073 5.729,1.271 0.354,0.198 10 false G48 1.271,0.75 1.875,0.99 0.604,0.24 10 false CANH*f 3.521,2.51 4.125,2.75 0.604,0.24 10 false CANL*g
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b Front view of DLC3
*c to No. 7 CAN Junction Connector *d to Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System)
*e to Parking Assist ECU (w/ Parking Assist Monitor System) *f to Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type with Multi-display])
*g to No. 1 CAN Junction Terminal - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Kinetic Dynamic Suspension System

*2: w/ Parking Assist Monitor System

*3: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type with Multi-display)

G287-1 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 7 CAN junction connector
G287-11 (CANL) - G48-4 (CG)
G287-2 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Stabilizer control ECU*1
G287-12 (CANL) - G48-4 (CG)
G287-4 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Parking assist ECU*2
G287-14 (CANL) - G48-4 (CG)
G287-5 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Clearance warning ECU assembly*3
G287-15 (CANL) - G48-4 (CG)
G287-10 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction terminal
G287-20 (CANL) - G48-4 (CG)



Result:
Result Proceed to
OK A
NG (No. 7 CAN junction connector CAN main wire) B
NG (Wire to ECU or sensor) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR- NO. 7 CAN JUNCTION CONNECTOR)

C

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)
a.
C368256C40
1.5,2 1.917,2.25 0.417,0.25 1.5,0.083 1.938,0.375 0.438,0.292 1.938,0.906 2.229,1.615 2.229,1.615 2.396,1.615 true 1.844,0.885 1.365,1.542 1.365,1.542 1.198,1.542 true 1.667,2.677 0.833,3.104 0.833,3.104 0.667,3.104 true 1.552,0.125 2.01,0.323 0.458,0.198 10 false G229 1.583,2.052 2.042,2.25 0.458,0.198 10 false G48 0.844,1.469 1.302,1.667 0.458,0.198 10 false CA5L 2.448,1.542 2.906,1.74 0.458,0.198 10 false CA5H 0.365,3.031 0.823,3.229 0.458,0.198 10 false CG 0.104,0.115 0.563,0.313 0.458,0.198 10 false *a 0.167,2.083 0.625,2.281 0.458,0.198 10 false *b
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Reconnect the wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-15 (CA5H) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-16 (CA5L) - G48-4 (CG)


HINT:
·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to GND in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPLACE CORRESPONDING ECU OR SENSOR