Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR


a.

Check the No. 1 CAN junction connector (for LHD).

i.
C382810C01
0.177,1.042 0.604,1.271 0.427,0.229 0.708,0.563 0.875,0.563 0.875,0.563 0.99,1.073 true 0.656,1.677 0.823,1.677 0.823,1.677 0.99,1.26 true 0.896,0.375 1.063,0.375 1.063,0.375 1.26,1.083 true 2.188,0.167 2.021,0.167 2.021,0.167 1.854,1.083 true 2.385,0.417 2.219,0.417 2.219,0.417 2.135,1.115 true 0.813,1.865 0.979,1.865 0.979,1.865 1.26,1.26 true 2.167,2.063 2,2.063 2,2.063 1.833,1.25 true 2.427,1.76 2.26,1.76 2.26,1.76 2.156,1.26 true 0.229,1.063 0.844,1.26 0.615,0.198 10 false A121 0.042,0.052 0.656,0.25 0.615,0.198 10 false *a 0.135,0.49 0.75,0.688 0.615,0.198 10 false CANH*b 0.354,0.281 0.969,0.479 0.615,0.198 10 false CANH*c 2.25,0.094 2.865,0.292 0.615,0.198 10 false CANH*d 2.438,0.344 3.052,0.542 0.615,0.198 10 false CANH*e 0.104,1.583 0.719,1.781 0.615,0.198 10 false CANL*b 0.313,1.771 0.927,1.969 0.615,0.198 10 false CANL*c 2.469,1.688 3.083,1.885 0.615,0.198 10 false CANL*e 2.229,1.979 2.844,2.177 0.615,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b for Suspension Control ECU (w/ Air Suspension System)
*c for Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System)
*d for No. 1 CAN Junction Terminal
*e for No. 3 CAN Junction Connector


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Air Suspension System

*2: w/ Pre-crash Safety System

A121-1 (CANH) GR Suspension control ECU*1
A121-7 (CANL) W
A121-2 (CANH) V Millimeter wave radar sensor assembly*2
A121-8 (CANL) W
A121-4 (CANH) LG No. 1 CAN junction terminal
A121-10 (CANL) W
A121-5 (CANH) B No. 3 CAN junction connector
A121-11 (CANL) W



b.

Check the No. 1 CAN junction connector (for RHD).

i.
C382810C02
0.177,1.042 0.604,1.271 0.427,0.229 0.708,0.563 0.875,0.563 0.875,0.563 0.99,1.073 true 0.656,1.677 0.823,1.677 0.823,1.677 0.99,1.26 true 0.896,0.375 1.063,0.375 1.063,0.375 1.26,1.083 true 2.188,0.167 2.021,0.167 2.021,0.167 1.854,1.083 true 2.385,0.417 2.219,0.417 2.219,0.417 2.135,1.115 true 0.813,1.865 0.979,1.865 0.979,1.865 1.26,1.26 true 2.167,2.063 2,2.063 2,2.063 1.833,1.25 true 2.427,1.76 2.26,1.76 2.26,1.76 2.156,1.26 true 0.229,1.063 0.844,1.26 0.615,0.198 10 false A121 0.042,0.052 0.656,0.25 0.615,0.198 10 false *a 0.135,0.49 0.75,0.688 0.615,0.198 10 false CANH*b 0.354,0.281 0.969,0.479 0.615,0.198 10 false CANH*c 2.25,0.094 2.865,0.292 0.615,0.198 10 false CANH*d 2.438,0.344 3.052,0.542 0.615,0.198 10 false CANH*e 0.104,1.583 0.719,1.781 0.615,0.198 10 false CANL*b 0.313,1.771 0.927,1.969 0.615,0.198 10 false CANL*c 2.469,1.688 3.083,1.885 0.615,0.198 10 false CANL*e 2.229,1.979 2.844,2.177 0.615,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b for Suspension Control ECU (w/ Air Suspension System)
*c for Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System)
*d for No. 7 CAN Junction Connector
*e for Central Gateway ECU (Network Gateway ECU)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Air Suspension System

*2: w/ Pre-crash Safety System

A121-1 (CANH) GR Suspension control ECU*1
A121-7 (CANL) W
A121-2 (CANH) V Millimeter wave radar sensor assembly*2
A121-8 (CANL) W
A121-4 (CANH) LG No. 7 CAN junction connector
A121-10 (CANL) W
A121-5 (CANH) B Central gateway ECU (network gateway ECU)
A121-11 (CANL) W




NO. 2 CAN JUNCTION CONNECTOR


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C349815C43
1.604,1.281 2.01,1.563 0.406,0.281 2.583,2 2.74,2 2.74,2 2.74,1.573 true 2.99,1.344 2.99,0.583 2.99,0.583 2.844,0.583 true 2.75,1.354 2.75,0.792 2.75,0.792 2.604,0.792 true 4.375,2.24 4.198,2.24 4.198,2.24 4.198,1.573 true 3.958,1.344 3.958,0.375 3.958,0.375 4.135,0.375 true 4.198,1.344 4.198,0.583 4.198,0.583 4.385,0.583 true 4.438,1.333 4.438,0.771 4.438,0.771 4.615,0.771 true 4.156,2.438 3.958,2.438 3.958,2.438 3.958,1.573 true 2.813,2.24 2.979,2.24 2.979,2.24 2.979,1.573 true 4.604,2 4.438,2 4.438,2 4.438,1.573 true 4.688,1.354 4.938,1.031 4.938,1.031 5.115,1.031 true 5.063,1.802 4.896,1.802 4.896,1.802 4.677,1.521 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 3.219,1.354 3.219,0.344 3.219,0.344 3.073,0.344 true 3.042,2.49 3.208,2.49 3.208,2.49 3.208,1.563 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.052,0.729 2.708,0.927 0.656,0.198 10 false CANH*c 2.042,1.948 2.698,2.146 0.656,0.198 10 false CANL*c 2.25,2.167 2.906,2.365 0.656,0.198 10 false CANL*d 2.302,0.51 2.958,0.708 0.656,0.198 10 false CANH*d 1.656,1.344 2.25,1.552 0.594,0.208 10 false G286 4.208,0.313 4.865,0.51 0.656,0.198 10 false CANH*f 4.479,0.51 5.135,0.708 0.656,0.198 10 false CANH*g 4.677,0.708 5.333,0.906 0.656,0.198 10 false CANH*h 4.219,2.375 4.875,2.573 0.656,0.198 10 false CANL*f 4.406,2.167 5.063,2.365 0.656,0.198 10 false CANL*g 4.667,1.948 5.323,2.146 0.656,0.198 10 false CANL*h 5.167,0.969 5.823,1.167 0.656,0.198 10 false CANH*i 5.115,1.729 5.771,1.927 0.656,0.198 10 false CANL*i 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b 2.521,0.271 3.177,0.469 0.656,0.198 10 false CANH*e 2.51,2.417 3.167,2.615 0.656,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b for No. 6 CAN Junction Connector
*c for Steering Sensor *d for Airbag Sensor Assembly
*e for No. 1 Headlight ECU Sub-assembly LH (for LHD with LED Headlight) *f for Tire Pressure Warning ECU and Receiver (for LHD with Tire Pressure Warning System)
*g for Combination Meter Assembly *h for Main Body ECU (Multiplex Network Body ECU)
*i for Master Cylinder Solenoid (Skid Control ECU) (except 2TR-FE) - -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: for LHD with LED Headlight

*2: for LHD with Tire Pressure Warning System

*3: except 2TR-FE

G286-1 (CANH) GR No. 6 CAN junction connector
G286-11 (CANL) W
G286-2 (CANH) G Steering sensor
G286-12 (CANL) W
G286-3 (CANH) Y Airbag sensor assembly
G286-13 (CANL) W
G286-4 (CANH) B No. 1 headlight ECU sub-assembly LH*1
G286-14 (CANL) W
G286-7 (CANH) LG Tire pressure warning ECU and receiver*2
G286-17 (CANL) W
G286-8 (CANH) V Combination meter assembly
G286-18 (CANL) W
G286-9 (CANH) L Main body ECU (multiplex network body ECU)
G286-19 (CANL) W
G286-10 (CANH) B Master cylinder solenoid (skid control ECU)*3
G286-20 (CANL) W




NO. 3 CAN JUNCTION CONNECTOR


a.

Check the No. 3 CAN junction connector (for LHD).

i.

Connection diagram

C349815C47
1.604,1.281 2.01,1.563 0.406,0.281 2.583,2 2.74,2 2.74,2 2.74,1.573 true 2.99,1.344 2.99,0.583 2.99,0.583 2.844,0.583 true 2.75,1.354 2.75,0.792 2.75,0.792 2.604,0.792 true 4.438,1.333 4.438,0.771 4.438,0.771 4.615,0.771 true 2.813,2.24 2.979,2.24 2.979,2.24 2.979,1.573 true 4.604,2 4.438,2 4.438,2 4.438,1.573 true 4.688,1.354 4.938,1.031 4.938,1.031 5.115,1.031 true 5.063,1.802 4.896,1.802 4.896,1.802 4.677,1.521 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.052,0.729 2.708,0.927 0.656,0.198 10 false CANH*c 2.042,1.948 2.698,2.146 0.656,0.198 10 false CANL*c 2.25,2.167 2.906,2.365 0.656,0.198 10 false CANL*d 2.302,0.51 2.958,0.708 0.656,0.198 10 false CANH*d 1.656,1.344 2.25,1.552 0.594,0.208 10 false G287 4.677,0.708 5.333,0.906 0.656,0.198 10 false CANH*e 4.667,1.948 5.323,2.146 0.656,0.198 10 false CANL*e 5.167,0.969 5.823,1.167 0.656,0.198 10 false CANH*f 5.125,1.729 5.781,1.927 0.656,0.198 10 false CANL*f 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b for No. 7 CAN Junction Connector
*c for Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System) *d for Forward Recognition Camera (w/ Pre-crash Safety System)
*e for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) *f for No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. Wiring Color Connected to

*1: w/ Kinetic Dynamic Suspension System

*2: w/ Pre-crash Safety System

*3: w/ Blind Spot Monitor System

G287-1 (CANH) P No. 7 CAN junction connector
G287-11 (CANL) W
G287-2 (CANH) V Stabilizer control ECU*1
G287-12 (CANL) W
G287-3 (CANH) GR Forward recognition camera*2
G287-13 (CANL) W
G287-9 (CANH) LG Blind spot monitor sensor LH*3
G287-19 (CANL) W
G287-10 (CANH) B No. 1 CAN junction connector
G287-20 (CANL) W



b.

Check the No. 3 CAN junction connector (for RHD).

i.

Connection diagram

C349815C50
1.604,1.281 2.01,1.563 0.406,0.281 2.583,2 2.74,2 2.74,2 2.74,1.573 true 3.219,1.344 3.219,0.583 3.219,0.583 3.073,0.583 true 2.75,1.354 2.75,0.792 2.75,0.792 2.604,0.792 true 3.469,1.333 3.469,0.771 3.469,0.771 3.646,0.771 true 3.052,2.24 3.219,2.24 3.219,2.24 3.219,1.573 true 3.656,2 3.49,2 3.49,2 3.49,1.573 true 4.688,1.354 4.938,1.031 4.938,1.031 5.115,1.031 true 5.063,1.802 4.896,1.802 4.896,1.802 4.677,1.521 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.052,0.729 2.708,0.927 0.656,0.198 10 false CANH*c 2.042,1.948 2.698,2.146 0.656,0.198 10 false CANL*c 2.51,2.167 3.167,2.365 0.656,0.198 10 false CANL*d 2.531,0.51 3.188,0.708 0.656,0.198 10 false CANH*d 1.656,1.344 2.25,1.552 0.594,0.208 10 false G287 3.677,0.708 4.333,0.906 0.656,0.198 10 false CANH*e 3.698,1.948 4.354,2.146 0.656,0.198 10 false CANL*e 5.167,0.969 5.823,1.167 0.656,0.198 10 false CANH*f 5.125,1.729 5.781,1.927 0.656,0.198 10 false CANL*f 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b for No. 7 CAN Junction Connector
*c for Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System) *d for Parking Assist ECU (w/ Parking Assist Monitor System)
*e for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type with Multi-display]) *f for No. 1 CAN Junction Terminal



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. Wiring Color Connected to

*1: w/ Kinetic Dynamic Suspension System

*2: w/ Parking Assist Monitor System

*3: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type with Multi-display)

G287-1 (CANH) P No. 7 CAN junction connector
G287-11 (CANL) W
G287-2 (CANH) V Stabilizer control ECU*1
G287-12 (CANL) W
G287-4 (CANH) B Parking assist ECU*2
G287-14 (CANL) W
G287-5 (CANH) R Clearance warning ECU assembly*3
G287-15 (CANL) W
G287-10 (CANH) LG No. 1 CAN junction connector
G287-20 (CANL) W




NO. 4 CAN JUNCTION CONNECTOR


a.

Check the No. 4 CAN junction connector.

i.
C379589C32
0.146,1.583 0.625,1.844 0.479,0.26 0.875,1.688 0.875,0.854 0.875,0.854 0.708,0.854 true 0.875,2.042 0.875,2.625 0.875,2.625 0.708,2.625 true 1.052,1.688 1.052,0.688 1.052,0.688 0.885,0.688 true 1.219,1.688 1.219,0.521 1.219,0.521 1.052,0.521 true 1.385,1.688 1.385,0.354 1.385,0.354 1.219,0.354 true 1.552,1.688 1.552,0.354 1.552,0.354 1.719,0.354 true 1.719,1.688 1.719,0.521 1.719,0.521 1.885,0.521 true 1.875,1.688 1.875,0.771 1.875,0.771 2.042,0.771 true 1.052,2.052 1.052,2.833 1.052,2.833 0.885,2.833 true 1.219,2.063 1.219,3 1.219,3 1.052,3 true 1.385,2.042 1.385,3.208 1.385,3.208 1.219,3.208 true 1.573,2.063 1.573,3.229 1.573,3.229 1.74,3.229 true 1.719,2.073 1.719,2.99 1.719,2.99 1.885,2.99 true 1.906,2.052 1.906,2.719 1.906,2.719 2.073,2.719 true 0.25,1.635 0.865,1.833 0.615,0.198 10 false G288 1.781,0.281 2.698,0.479 0.917,0.198 10 false CANH*f 2.115,2.667 3.031,2.865 0.917,0.198 10 false CANL*h 0.156,0.792 1.073,0.99 0.917,0.198 10 false CANH*b 0.167,2.542 1.083,2.74 0.917,0.198 10 false CANL*b 0.052,0.083 0.969,0.281 0.917,0.198 10 false *a 0.313,0.604 1.229,0.802 0.917,0.198 10 false CANH*c 0.5,0.438 1.417,0.635 0.917,0.198 10 false CANH*d 0.656,0.271 1.573,0.469 0.917,0.198 10 false CANH*e 1.927,0.458 2.844,0.656 0.917,0.198 10 false CANH*g 2.094,0.698 3.01,0.896 0.917,0.198 10 false CANH*h 0.354,2.76 1.271,2.958 0.917,0.198 10 false CANL*c 0.521,2.927 1.438,3.125 0.917,0.198 10 false CANL*d 0.688,3.135 1.604,3.333 0.917,0.198 10 false CANL*e 1.813,3.167 2.729,3.365 0.917,0.198 10 false CANL*f 1.938,2.906 2.854,3.104 0.917,0.198 10 false CANL*g
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b for Outer Mirror Control ECU Assembly RH (w/ Reverse Shift-linked Mirror)
*c for Front Power Seat Switch (Power Seat Control ECU) (w/ Seat Memory)
*d for Multiplex Tilt and Telescopic ECU (for Power Tilt and Power Telescopic Steering Column)
*e for Main Body ECU (Multiplex Network Body ECU)
*f for Rear Television Camera Assembly (w/ Rear Television Camera Assembly [built-in ECU])
*g for Outer Mirror Control ECU Assembly LH (w/ Reverse Shift-linked Mirror)
*h for No. 2 CAN Junction Terminal


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Reverse Shift-linked Mirror

*2: for Power Tilt and Power Telescopic Steering Column

*3: w/ Rear Television Camera Assembly (built-in ECU)

*4: w/ Seat Memory

G288-1 (CANH) G Outer mirror control ECU assembly RH*1
G288-12 (CANL) W
G288-2 (CANH) L Front power seat switch (power seat control ECU)*4
G288-13 (CANL) W
G288-3 (CANH) GR Multiplex tilt and telescopic ECU*2
G288-14 (CANL) W
G288-4 (CANH) P Main body ECU (multiplex network body ECU)
G288-15 (CANL) W
G288-5 (CANH) B Rear television camera assembly*3
G288-16 (CANL) W
G288-6 (CANH) R Outer mirror control ECU assembly LH*1
G288-17 (CANL) W
G288-7 (CANH) LG No. 2 CAN junction terminal
G288-18 (CANL) W




NO. 5 CAN JUNCTION CONNECTOR


a.

Check the No. 5 CAN junction connector.

i.
C382809C02
0.135,1.49 0.521,1.719 0.385,0.229 0.708,0.75 0.875,0.75 0.875,0.75 0.875,1.583 true 0.708,2.604 0.875,2.604 0.875,2.604 0.875,1.938 true 1.375,0.417 1.208,0.417 1.208,0.417 1.208,1.583 true 0.854,0.5 1.021,0.5 1.021,0.5 1.021,1.583 true 1.542,0.615 1.375,0.615 1.375,0.615 1.375,1.583 true 1.688,0.833 1.521,0.833 1.521,0.833 1.521,1.583 true 0.865,2.854 1.031,2.854 1.031,2.854 1.031,1.938 true 1.385,3 1.219,3 1.219,3 1.219,1.917 true 1.531,2.781 1.365,2.781 1.365,2.781 1.365,1.948 true 1.708,2.542 1.542,2.542 1.542,2.542 1.542,1.958 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.156,1.51 0.531,1.708 0.375,0.198 10 false G289 0.146,0.677 0.708,0.948 0.563,0.271 10 false CANH*b 0.188,2.521 0.75,2.792 0.563,0.271 10 false CANL*b 0.333,0.427 0.896,0.698 0.563,0.271 10 false CANH*c 0.302,2.771 0.865,3.042 0.563,0.271 10 false CANL*c 1.448,0.344 2.01,0.615 0.563,0.271 10 false CANH*d 1.583,0.542 2.146,0.813 0.563,0.271 10 false CANH*e 1.74,0.76 2.302,1.031 0.563,0.271 10 false CANH*f 1.438,2.917 2,3.188 0.563,0.271 10 false CANL*d 1.583,2.719 2.146,2.99 0.563,0.271 10 false CANL*e 1.76,2.458 2.323,2.729 0.563,0.271 10 false CANL*f
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b for Central Gateway ECU (Network Gateway ECU)
*c for Central Gateway ECU (Network Gateway ECU)
*d
·

for Navigation Receiver Assembly (EMVN ECU) (w/ Navigation System)

·

for Radio and Display Receiver Assembly (EMVN ECU) (w/ Audio and Visual System)


*e for Telematics Transceiver (w/ Telematics Transceiver)
*f for Bus Buffer ECU (w/ Bus Buffer ECU)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Navigation System

*2: w/ Audio and Visual System

*3: w/ Telematics Transceiver

*4: w/ Bus Buffer ECU

G289-1 (CANH) G Central gateway ECU (network gateway ECU)
G289-12 (CANL) W
G289-2 (CANH) L Central gateway ECU (network gateway ECU)
G289-13 (CANL) W
G289-3 (CANH) R
·

Navigation receiver assembly (EMVN ECU)*1

·

Radio and display receiver assembly (EMVN ECU)*2


G289-14 (CANL) W
G289-4 (CANH) P Telematics transceiver*3
G289-15 (CANL) W
G289-5 (CANH) B Bus buffer ECU*4
G289-16 (CANL) W




NO. 6 CAN JUNCTION CONNECTOR


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C349815C42
1.604,1.281 2.01,1.563 0.406,0.281 2.583,2 2.74,2 2.74,2 2.74,1.573 true 2.99,1.344 2.99,0.583 2.99,0.583 2.844,0.583 true 2.75,1.354 2.75,0.792 2.75,0.792 2.604,0.792 true 3.229,1.354 3.229,0.385 3.229,0.385 3.073,0.385 true 4.375,2.24 4.198,2.24 4.198,2.24 4.198,1.573 true 3.469,1.344 3.469,0.188 3.469,0.188 3.313,0.188 true 3.719,1.344 3.719,0.188 3.719,0.188 3.896,0.188 true 3.958,1.344 3.958,0.375 3.958,0.375 4.135,0.375 true 4.198,1.344 4.198,0.583 4.198,0.583 4.385,0.583 true 4.438,1.333 4.438,0.771 4.438,0.771 4.615,0.771 true 3.052,2.448 3.229,2.448 3.229,2.448 3.229,1.583 true 3.896,2.635 3.719,2.635 3.719,2.635 3.719,1.573 true 3.292,2.635 3.469,2.635 3.469,2.635 3.469,1.573 true 4.156,2.438 3.958,2.438 3.958,2.438 3.958,1.573 true 2.813,2.24 2.979,2.24 2.979,2.24 2.979,1.573 true 4.604,2 4.438,2 4.438,2 4.438,1.573 true 4.688,1.354 4.938,1.031 4.938,1.031 5.115,1.031 true 5.063,1.802 4.896,1.802 4.896,1.802 4.677,1.521 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.052,0.729 2.708,0.927 0.656,0.198 10 false CANH*c 2.042,1.948 2.698,2.146 0.656,0.198 10 false CANL*c 2.25,2.167 2.906,2.365 0.656,0.198 10 false CANL*d 2.302,0.51 2.958,0.708 0.656,0.198 10 false CANH*d 2.542,0.323 3.198,0.521 0.656,0.198 10 false CANH*e 1.656,1.344 2.25,1.552 0.594,0.208 10 false G290 2.771,0.115 3.427,0.313 0.656,0.198 10 false CANH*f 3.948,0.125 4.604,0.323 0.656,0.198 10 false CANH*g 4.208,0.313 4.865,0.51 0.656,0.198 10 false CANH*h 4.479,0.51 5.135,0.708 0.656,0.198 10 false CANH*i 4.677,0.708 5.333,0.906 0.656,0.198 10 false CANH*j 2.521,2.375 3.177,2.573 0.656,0.198 10 false CANL*e 2.771,2.573 3.427,2.771 0.656,0.198 10 false CANL*f 3.958,2.573 4.615,2.771 0.656,0.198 10 false CANL*g 4.219,2.375 4.875,2.573 0.656,0.198 10 false CANL*h 4.417,2.177 5.073,2.375 0.656,0.198 10 false CANL*i 4.667,1.948 5.323,2.146 0.656,0.198 10 false CANL*j 5.167,0.969 5.823,1.167 0.656,0.198 10 false CANH*k 5.125,1.729 5.781,1.927 0.656,0.198 10 false CANL*k 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b for No. 2 CAN Junction Connector
*c for 4 Wheel Drive Control ECU (4WD Control ECU) *d for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*e for No. 1 Headlight ECU Sub-assembly LH (for RHD with LED Headlight) *f for Tire Pressure Warning ECU and Receiver (for RHD with Tire Pressure Warning System)
*g for Central Gateway ECU (Network Gateway ECU) *h for Air Conditioning Amplifier Assembly
*i for Power Steering ECU Assembly *j for Brake Actuator Assembly (Skid Control ECU) (for 2TR-FE)
*k for ECM - -



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Entry and Start System

*2: for RHD with LED Headlight

*3: for RHD with Tire Pressure Warning System

*4: for 2TR-FE

G290-1 (CANH) GR No. 2 CAN junction connector
G290-11 (CANL) W
G290-2 (CANH) G 4 Wheel drive control ECU (4WD control ECU)
G290-12 (CANL) W
G290-3 (CANH) P Certification ECU (smart key ECU assembly)*1
G290-13 (CANL) W
G290-4 (CANH) V No. 1 headlight ECU sub-assembly LH*2
G290-14 (CANL) W
G290-5 (CANH) LG Tire pressure warning ECU and receiver*3
G290-15 (CANL) W
G290-6 (CANH) BR Central gateway ECU (network gateway ECU)
G290-16 (CANL) W
G290-7 (CANH) V Air conditioning amplifier assembly
G290-17 (CANL) W
G290-8 (CANH) L Power steering ECU assembly
G290-18 (CANL) W
G290-9 (CANH) R Brake actuator assembly (skid control ECU)*4
G290-19 (CANL) W
G290-10 (CANH) LG ECM
G290-20 (CANL) W




NO. 7 CAN JUNCTION CONNECTOR


a.

Check the No. 7 CAN junction connector (for LHD).

i.

Connection diagram

C349815C48
1.604,1.281 2.01,1.563 0.406,0.281 2.583,2 2.74,2 2.74,2 2.74,1.573 true 2.99,1.344 2.99,0.583 2.99,0.583 2.844,0.583 true 2.75,1.354 2.75,0.792 2.75,0.792 2.604,0.792 true 3.229,1.365 3.229,0.573 3.229,0.573 3.406,0.573 true 2.813,2.24 2.979,2.24 2.979,2.24 2.979,1.573 true 3.396,2.26 3.229,2.26 3.229,2.26 3.229,1.563 true 3.49,1.365 3.802,0.823 3.802,0.823 3.979,0.823 true 3.823,2.031 3.656,2.031 3.656,2.031 3.49,1.521 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.052,0.729 2.708,0.927 0.656,0.198 10 false CANH*c 2.042,1.948 2.698,2.146 0.656,0.198 10 false CANL*c 2.25,2.167 2.906,2.365 0.656,0.198 10 false CANL*d 2.302,0.51 2.958,0.708 0.656,0.198 10 false CANH*d 1.656,1.344 2.25,1.552 0.594,0.208 10 false G291 3.479,0.5 4.135,0.698 0.656,0.198 10 false CANH*e 3.438,2.188 4.094,2.385 0.656,0.198 10 false CANL*e 4.031,0.75 4.688,0.948 0.656,0.198 10 false CANH*f 3.875,1.958 4.531,2.156 0.656,0.198 10 false CANL*f 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for No. 3 CAN Junction Connector
*c for Central Gateway ECU (Network Gateway ECU) *d for Parking Assist ECU (w/ Parking Assist Monitor System)
*e for Driving Support ECU Assembly (w/ Pre-crash Safety System) *f for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [w/ Multi-display])



ii.

Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Parking Assist Monitor System

*2: w/ Pre-crash Safety System

*3: w/ TOYOTA Parking Assist-sensor System (w/ Multi-display)

G291-1 (CANH) P No. 3 CAN junction connector
G291-11 (CANL) W
G291-2 (CANH) V Central gateway ECU (network gateway ECU)
G291-12 (CANL) W
G291-3 (CANH) B Parking assist ECU*1
G291-13 (CANL) W
G291-4 (CANH) G Driving support ECU assembly*2
G291-14 (CANL) W
G291-5 (CANH) R Clearance warning ECU assembly*3
G291-15 (CANL) W



b.

Check the No. 7 CAN junction connector (for RHD).

i.

Connection diagram

C349815C49
1.604,1.281 2.01,1.563 0.406,0.281 3,1.385 2.99,0.583 2.99,0.583 2.844,0.583 true 3.208,1.385 3.333,0.198 3.333,0.198 3.51,0.198 true 2.813,2.24 2.979,2.24 2.979,2.24 2.979,1.573 true 3.542,2.615 3.375,2.615 3.375,2.615 3.208,1.542 true 3.458,1.354 3.646,0.375 3.646,0.375 3.823,0.375 true 3.823,2.438 3.656,2.438 3.656,2.438 3.469,1.542 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 3.708,1.375 3.938,0.594 3.938,0.594 4.115,0.594 true 4.063,2.25 3.896,2.25 3.896,2.25 3.708,1.542 true 3.927,1.385 4.167,0.813 4.167,0.813 4.344,0.813 true 4.25,2.052 4.083,2.052 4.083,2.052 3.948,1.542 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.25,2.167 2.906,2.365 0.656,0.198 10 false CANL*c 2.302,0.51 2.958,0.708 0.656,0.198 10 false CANH*c 1.656,1.344 2.25,1.552 0.594,0.208 10 false G291 3.552,0.135 4.208,0.333 0.656,0.198 10 false CANH*d 3.573,2.563 4.229,2.76 0.656,0.198 10 false CANL*d 3.875,0.313 4.531,0.51 0.656,0.198 10 false CANH*e 3.865,2.385 4.521,2.583 0.656,0.198 10 false CANL*e 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b 4.167,0.51 4.823,0.708 0.656,0.198 10 false CANH*f 4.115,2.177 4.771,2.375 0.656,0.198 10 false CANL*f 4.385,0.74 5.042,0.938 0.656,0.198 10 false CANH*g 4.302,1.969 4.958,2.167 0.656,0.198 10 false CANL*g
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b for No. 3 CAN Junction Connector
*c for No. 1 CAN Junction Connector *d for Driving Support ECU Assembly (w/ Pre-crash Safety System)
*e for Forward Recognition Camera (w/ Pre-crash Safety System) *f for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System)
*g for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type with Multi-display]) - -



ii.

Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to

*1: w/ Pre-crash Safety System

*2: w/ Blind Spot Monitor System

*3: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type with Multi-display)

G291-1 (CANH) P No. 3 CAN junction connector
G291-11 (CANL) W
G291-3 (CANH) LG No. 1 CAN junction connector
G291-13 (CANL) W
G291-4 (CANH) G Driving support ECU assembly*1
G291-14 (CANL) W
G291-5 (CANH) GR Forward recognition camera*1
G291-15 (CANL) W
G291-6 (CANH) LG Blind spot monitor sensor LH*2
G291-16 (CANL) W
G291-7 (CANH) R Clearance warning ECU assembly*3
G291-17 (CANL) W




NO. 1 CAN JUNCTION TERMINAL


a.

Check the No. 1 CAN junction terminal.

i.
C210060C79
2.625,0.875 3.083,1.156 0.458,0.281 1.354,1.083 1.125,1.344 1.125,1.344 0.938,1.344 true 1.729,0.875 1.469,0.438 1.469,0.438 1.302,0.438 true 0.406,1.281 1.354,1.656 0.948,0.375 10 false CANH*b 2.708,0.948 3.156,1.219 0.448,0.271 10 false G298 0.76,0.375 1.635,0.531 0.875,0.156 10 false CANL*b 0.094,0.083 0.969,0.24 0.875,0.156 10 false *a
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)
*b
·

for No. 1 CAN Junction Connector (for LHD)

·

for No. 3 CAN Junction Connector (for RHD)




Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to

*1: for LHD

*2: for RHD

G298-3 (CANH) LG
·

No. 1 CAN junction connector*1

·

No. 3 CAN junction connector*2


G298-2 (CANL) W




NO. 2 CAN JUNCTION TERMINAL


a.

Check the No. 2 CAN junction terminal.

i.
C210060C78
2.625,0.875 3.083,1.156 0.458,0.281 1.354,1.083 1.125,1.344 1.125,1.344 0.938,1.344 true 1.729,0.875 1.469,0.438 1.469,0.438 1.302,0.438 true 0.396,1.281 1.344,1.656 0.948,0.375 10 false CANP*b 2.729,0.938 3.177,1.208 0.448,0.271 10 false G299 0.76,0.375 1.635,0.531 0.875,0.156 10 false CANN*b 0.094,0.083 0.969,0.24 0.875,0.156 10 false *a
*a Rear view of wire harness connector
(to No. 2 CAN Junction Terminal)
*b for No. 4 CAN Junction Connector


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
G299-3 (CANP) LG No. 4 CAN junction connector
G299-2 (CANN) W




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C349818C21
1.625,1.313 2.042,1.583 0.417,0.271 3.865,1.125 3.865,0.51 3.865,0.51 4.052,0.51 true 3.51,1.125 3.51,0.51 3.51,0.51 3.313,0.51 true 4.417,2.24 4.229,2.24 4.229,2.24 4.229,1.708 true 3.667,2.24 3.865,2.24 3.865,2.24 3.865,1.708 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.156,0.458 4.792,0.688 0.635,0.229 10 false CANH 3.26,2.198 3.896,2.427 0.635,0.229 10 false CANL 3.042,0.469 3.677,0.698 0.635,0.229 10 false CG 4.51,2.177 5.146,2.406 0.635,0.229 10 false BAT 1.729,1.396 2.365,1.625 0.635,0.229 10 false G48
*a Front view of DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G48-6 (CANH) - G48-4 (CG) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G48-14 (CANL) - G48-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G48-6 (CANH) - G48-16 (BAT) P - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C349819C38
1.083,1.281 1.5,1.552 0.417,0.271 3.615,2.51 3.448,2.51 3.448,2.51 3.448,1.427 true 3.552,2.667 3.365,2.667 3.365,2.667 3.365,1.427 true 3.24,1.292 3.24,0.26 3.24,0.26 3.125,0.26 true 3.542,1.375 3.542,0.51 3.542,0.51 3.698,0.51 true 3.115,2.615 3.281,2.615 3.281,2.615 3.281,1.427 true 3.625,1.385 3.625,0.667 3.625,0.667 3.781,0.667 true 3.885,2.354 3.719,2.354 3.719,2.354 3.719,1.438 true 3.958,2.188 3.792,2.188 3.792,2.188 3.792,1.427 true 4.042,2 3.875,2 3.875,2 3.875,1.427 true 3.917,1.292 3.917,0.854 3.917,0.854 4.073,0.854 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.75,0.198 3.24,0.375 0.49,0.177 10 false CA3H 2.75,2.563 3.302,2.781 0.552,0.219 10 false CA3L 3.688,2.448 4.177,2.625 0.49,0.177 10 false CAYH 3.625,2.604 4.115,2.781 0.49,0.177 10 false CAYL 3.771,0.448 4.26,0.625 0.49,0.177 10 false CA4H 4.135,0.792 4.688,1.01 0.552,0.219 10 false CA6L 4.031,2.125 4.521,2.302 0.49,0.177 10 false CA5H 3.969,2.292 4.521,2.51 0.552,0.219 10 false CA5L 1.146,1.333 1.594,1.594 0.448,0.26 10 false G229 4.115,1.938 4.604,2.115 0.49,0.177 10 false CA6H 3.854,0.604 4.406,0.823 0.552,0.219 10 false CA4L
*a Component without harness connected
(Central Gateway ECU [Network Gateway ECU])
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.

C349820C31
1.094,1.708 1.5,1.979 0.406,0.271 4.125,1.74 4.125,0.458 4.125,0.458 4.281,0.458 true 4.052,1.99 4.052,3.281 4.052,3.281 4.208,3.281 true 3.906,1.99 3.906,3.448 3.906,3.448 3.74,3.448 true 3.76,1.979 3.76,3.271 3.76,3.271 3.604,3.271 true 3.604,1.885 3.604,0.458 3.604,0.458 3.448,0.458 true 3.458,1.885 3.458,0.646 3.458,0.646 3.302,0.646 true 3.313,1.99 3.313,3.052 3.313,3.052 3.156,3.052 true 3.156,1.99 3.156,2.875 3.156,2.875 3,2.875 true 2.938,1.75 2.938,0.948 2.938,0.948 2.781,0.948 true 3.01,1.969 3.01,2.604 3.01,2.604 2.854,2.604 true 2.333,1.771 2.333,1.167 2.333,1.167 2.177,1.167 true 4.781,1.802 5.229,1.802 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.156,1.76 1.531,1.969 0.375,0.208 10 false G229 4.385,0.406 5.344,0.688 0.958,0.281 10 false CA3H 3.031,0.396 3.99,0.677 0.958,0.281 10 false CA4H 2.594,2.823 3.552,3.104 0.958,0.281 10 false CA5H 3.177,3.219 4.135,3.5 0.958,0.281 10 false CAYH 4.292,3.219 5.25,3.5 0.958,0.281 10 false CA3L 2.906,0.594 3.865,0.875 0.958,0.281 10 false CA4L 2.792,3 3.75,3.281 0.958,0.281 10 false CA5L 3.365,3.396 4.323,3.677 0.958,0.281 10 false CAYL 2.458,2.542 3.417,2.823 0.958,0.281 10 false CA6H 2.396,0.896 3.354,1.177 0.958,0.281 10 false CA6L 1.771,1.104 2.729,1.385 0.958,0.281 10 false BATT 5.302,1.74 5.865,1.99 0.563,0.25 10 false GND
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines (DLC3 - Central Gateway ECU [Network Gateway ECU])
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G229-14 (CA6H) - G229-5 (CA6L) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
G229-14 (CA6H) - G229-10 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-5 (CA6L) - G229-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-14 (CA6H) - G229-1 (BATT) P - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G229-5 (CA6L) - G229-1 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G229-18 (CA4H) - G229-17 (CA4L) BR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G229-18 (CA4H) - G229-10 (GND) BR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-17 (CA4L) - G229-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-18 (CA4H) - G229-1 (BATT) BR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G229-17 (CA4L) - G229-1 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G229-6 (CA3H) - G229-21 (CA3L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
G229-6 (CA3H) - G229-19 (CAYH) G - L HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G229-21 (CA3L) - G229-20 (CAYL) W - W LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
G229-6 (CA3H) - G229-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-21 (CA3L) - G229-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-6 (CA3H) - G229-1 (BATT) G - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G229-21 (CA3L) - G229-1 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: for LHD

*2: for RHD

G229-15 (CA5H) - G229-16 (CA5L) V - W*1
B - W*2
HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G229-15 (CA5H) - G229-10 (GND) V - W-B*1
B - W-B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-16 (CA5L) - G229-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G229-15 (CA5H) - G229-1 (BATT) V - L*1
B - L*2
HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G229-16 (CA5L) - G229-1 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 1GR-FE)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

C382826C01
1.698,0.24 2.115,0.469 0.417,0.229 5.073,0.167 5.49,0.396 0.417,0.229 2.333,1.917 2.75,1.917 true 2.438,1.469 2.854,1.469 true 4.396,1.917 4.813,1.917 true 4.313,1.49 4.469,1.49 4.469,1.49 4.813,1.74 true 5.104,1.917 5.26,2.427 5.26,2.427 5.427,2.427 true 0.854,1.042 1.01,1.042 1.01,1.042 1.677,1.188 true 0.073,0.031 0.385,0.229 0.313,0.198 10 false *a 1.76,0.271 2.073,0.469 0.313,0.198 10 false G55 5.146,0.198 5.458,0.396 0.313,0.198 10 false G56 2.792,1.854 3.313,2.115 0.521,0.26 10 false BATT 2.896,1.375 3.417,1.635 0.521,0.26 10 false EC*B 3.792,1.833 4.448,2.208 0.656,0.375 10 false CANH*A, CANL*B 3.771,1.417 4.427,1.792 0.656,0.375 10 false CANL*A 5.448,2.354 6.073,2.604 0.625,0.25 10 false CANH*B 0.469,0.958 0.99,1.219 0.521,0.26 10 false EC*A
*A for Automatic Transmission *B for Manual Transmission
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G56-31 (CANH) - G55-3 (EC) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G56-25 (CANL) - G55-3 (EC) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G56-31 (CANH) - G55-24 (BATT) LG - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G56-25 (CANL) - G55-24 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for Manual Transmission
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G56-32 (CANH) - G56-31 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G56-32 (CANH) - G55-12 (EC) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G56-31 (CANL) - G55-12 (EC) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G56-32 (CANH) - G55-24 (BATT) LG - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G56-31 (CANL) - G55-24 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 1KD-FTV)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

C382826C02
1.698,0.24 2.115,0.469 0.417,0.229 5.073,0.167 5.49,0.396 0.417,0.229 2.021,1.979 2.25,2.417 2.25,2.417 2.5,2.417 true 5.615,1.917 5.771,2.427 5.771,2.427 5.938,2.427 true 2.063,1.417 2.688,1.26 2.688,1.26 2.938,1.26 true 5.698,1.927 5.865,1.688 5.865,1.688 6.115,1.688 true 0.073,0.031 0.385,0.229 0.313,0.198 10 false *a 1.76,0.271 2.073,0.469 0.313,0.198 10 false G57 5.146,0.198 5.458,0.396 0.313,0.198 10 false G58 2.563,2.344 3.083,2.604 0.521,0.26 10 false BATT 2.979,1.188 3.5,1.448 0.521,0.26 10 false EC 6,2.344 6.625,2.594 0.625,0.25 10 false CANH 6.167,1.594 6.792,1.844 0.625,0.25 10 false CANL
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G58-35 (CANH) - G57-11 (EC) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G58-36 (CANL) - G57-11 (EC) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G58-35 (CANH) - G57-23 (BATT) LG - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G58-36 (CANL) - G57-23 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 1GD-FTV)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

C382827C01
1.99,0.208 2.49,0.448 0.5,0.24 4.865,0.25 5.365,0.49 0.5,0.24 3.927,1.302 4.094,1.302 4.094,1.302 4.469,1.573 false 4.073,2.042 4.24,2.042 4.24,2.042 4.479,1.792 false 1.021,0.875 1.188,0.875 1.188,0.875 1.563,1.146 false 0.979,1.625 1.146,1.625 1.146,1.625 1.521,1.479 true 2.042,0.271 2.656,0.469 0.615,0.198 10 false G185 4.938,0.302 5.552,0.5 0.615,0.198 10 false G184 0.073,0.094 0.688,0.292 0.615,0.198 10 false *a 3.51,1.25 4.125,1.448 0.615,0.198 10 false CANH 3.677,1.979 4.292,2.177 0.615,0.198 10 false CANL 0.646,0.813 1.26,1.01 0.615,0.198 10 false BATT 0.729,1.563 1.344,1.76 0.615,0.198 10 false EC
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G184-17 (CANH) - G184-28 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G184-17 (CANH) - G185-8 (EC) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G184-28 (CANL) - G185-8 (EC) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G184-17 (CANH) - G185-1 (BATT) LG - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G184-28 (CANL) - G185-1 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 2TR-FE)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connectors.

C382827C02
1.99,0.208 2.49,0.448 0.5,0.24 4.865,0.25 5.365,0.49 0.5,0.24 4.656,2.302 4.823,2.302 4.823,2.302 5.448,1.469 true 4.771,2.542 4.938,2.542 4.938,2.542 5.604,1.5 true 1.302,0.604 1.469,0.604 1.469,0.604 1.958,1.135 true 0.979,1.76 1.146,1.76 1.146,1.76 1.521,1.615 true 2.042,0.271 2.656,0.469 0.615,0.198 10 false G180 4.938,0.302 5.552,0.5 0.615,0.198 10 false G181 0.073,0.094 0.688,0.292 0.615,0.198 10 false *a 4.198,2.219 4.813,2.417 0.615,0.198 10 false CANH 4.385,2.479 5,2.677 0.615,0.198 10 false CANL 0.927,0.542 1.542,0.74 0.615,0.198 10 false BATT 0.729,1.677 1.344,1.875 0.615,0.198 10 false EC
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G181-13 (CANH) - G181-14 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G181-13 (CANH) - G180-18 (EC) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G181-14 (CANL) - G180-18 (EC) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G181-13 (CANH) - G180-3 (BATT) LG - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G181-14 (CANL) - G180-3 (BATT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (for 2TR-FE)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>TERMINALS OF ECU

a.
U148964C02
2.51,1.25 2.781,2.021 2.781,2.021 2.917,2.021 true 1.115,0.844 0.708,0.354 0.708,0.354 0.573,0.354 true 1.313,1.365 1.635,1.917 1.635,1.917 1.781,1.917 true 1.302,1.219 0.813,1.854 0.813,1.854 0.677,1.854 true 0.083,0.271 0.542,0.417 0.458,0.146 10 false GND1 3,1.917 3.313,2.063 0.313,0.146 10 false BM 1.698,0.125 2.01,0.313 0.313,0.188 10 false A6 1.844,1.844 2.365,2.063 0.521,0.219 10 false CANH 0.323,1.781 0.844,2 0.521,0.219 10 false CANL 0.042,0.042 0.5,0.188 0.458,0.146 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A6-25 (CANH) - A6-1 (GND1) R - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A6-14 (CANL) - A6-1 (GND1) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A6-25 (CANH) - A6-24 (BM) R - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A6-14 (CANL) - A6-24 (BM) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (except 2TR-FE)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>TERMINALS OF ECU

a.

Disconnect the master cylinder solenoid (skid control ECU) connector.

U170045C01
2.146,0.677 2.313,0.219 2.313,0.219 2.406,0.219 true 2.156,0.969 2.417,1.635 2.417,1.635 2.51,1.635 true 3.927,0.688 3.75,0.229 3.75,0.229 3.646,0.229 true 4.24,0.698 4.417,0.302 4.417,0.302 4.521,0.302 true 2.542,1.563 2.969,1.729 0.427,0.167 10 false CANL 2.448,0.146 2.875,0.313 0.427,0.167 10 false CANH 3.26,0.146 3.656,0.313 0.396,0.167 10 false +BM1 4.563,0.229 5.01,0.396 0.448,0.167 10 false GND1 4.958,0.844 5.25,1.01 0.292,0.167 10 false A8 0.479,0.865 0.771,1.031 0.292,0.167 10 false A7 0.063,0.073 0.49,0.24 0.427,0.167 10 false *a
*a Rear view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A7-11 (CANH) - A7-1 (GND1) B - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A7-25 (CANL) - A7-1 (GND1) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A7-11 (CANH) - A7-2 (+BM1) B - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A7-25 (CANL) - A7-2 (+BM1) W - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


Refer to Terminals of ECU.

for Automatic Air Conditioning System: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>TERMINALS OF ECU

for Manual Air Conditioning System: Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379594C10
1.531,0.229 1.969,0.427 0.438,0.198 0.896,2.427 0.729,2.427 0.729,2.427 0.563,1.927 true 1,0.865 1.198,0.865 1.198,0.865 1.792,1.719 true 1.396,0.646 1.594,0.646 1.594,0.646 1.917,1.719 true 2.385,0.781 2.219,0.781 2.219,0.781 2.135,1.75 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.021,0.594 1.479,0.792 0.458,0.198 10 false CANL 0.594,0.781 1.052,0.979 0.458,0.198 10 false CANH 2.438,0.698 2.896,0.896 0.458,0.198 10 false GND 0.948,2.344 1.406,2.542 0.458,0.198 10 false B 1.573,0.24 2.031,0.438 0.458,0.198 10 false G25
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G25-11 (CANH) - G25-14 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G25-12 (CANL) - G25-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G25-11 (CANH) - G25-21 (B) V - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G25-12 (CANL) - G25-21 (B) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


b.
C227529C11
0.375,2.521 0.771,2.781 0.396,0.26 0.365,0.948 0.76,1.208 0.396,0.26 2.198,2.896 2.333,3.115 2.333,3.115 2.552,3.115 true 2.115,1.323 2.313,1.677 2.313,1.677 2.552,1.677 true 2.021,1.01 2.438,0.656 2.438,0.656 2.688,0.656 true 1.208,1.677 1.438,1.677 1.438,1.677 1.76,1.323 true 0.177,0.073 0.427,0.271 0.25,0.198 10 false *a 0.198,2.083 0.51,2.24 0.313,0.156 10 false *b 0.479,2.573 0.823,2.781 0.344,0.208 10 false G48 0.458,1 0.802,1.208 0.344,0.208 10 false G1 2.75,0.583 3.292,0.792 0.542,0.208 10 false CANH 2.604,1.604 3.146,1.813 0.542,0.208 10 false CANL 2.604,3.042 3.146,3.25 0.542,0.208 10 false BAT 1,1.604 1.542,1.813 0.542,0.208 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3


Disconnect the airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G1-13 (CANH) - G1-25 (E1) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G1-22 (CANL) - G1-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G1-13 (CANH) - G48-16 (BAT) Y - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G1-22 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379594C09
1.531,0.229 1.969,0.427 0.438,0.198 2.635,0.906 2.802,0.906 2.802,0.906 2.896,1.771 true 0.896,2.427 0.729,2.427 0.729,2.427 0.563,1.927 true 2.51,2.615 2.708,2.615 2.708,2.615 2.906,1.917 true 2.146,2.365 2.344,2.365 2.344,2.365 2.792,1.917 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.698,2.281 2.156,2.479 0.458,0.198 10 false CANL 2.104,2.521 2.563,2.719 0.458,0.198 10 false CANH 2.438,0.833 2.896,1.031 0.458,0.198 10 false E2 0.948,2.344 1.406,2.542 0.458,0.198 10 false B 1.573,0.24 2.031,0.438 0.458,0.198 10 false G304
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G304-40 (CANH) - G304-39 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G304-40 (CANH) - G304-20 (E2) V - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G304-39 (CANL) - G304-20 (E2) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G304-40 (CANH) - G304-21 (B) V - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G304-39 (CANL) - G304-21 (B) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


C349821C06
4.385,0.406 4.802,0.667 0.417,0.26 4.875,2.26 4.729,2.26 4.729,2.26 4.729,1.667 true 4.479,2.26 4.625,2.26 4.625,2.26 4.625,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.448,0.469 4.906,0.667 0.458,0.198 10 false G205 4.948,2.208 5.531,2.458 0.583,0.25 10 false CANL 4.063,2.208 4.646,2.458 0.583,0.25 10 false CANH
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C382824C03
1.438,0.135 1.875,0.427 0.438,0.292 1.167,1.75 1.333,1.75 1.333,1.75 1.531,1.302 true 2.073,1.75 1.906,1.75 1.906,1.75 1.719,1.281 true 0.854,1.375 1.021,1.375 1.021,1.375 1.344,1.188 true 2.594,1.385 2.427,1.385 2.427,1.385 2.042,1.24 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.458,0.208 1.896,0.427 0.438,0.219 10 false G205 0.771,1.677 1.208,1.896 0.438,0.219 10 false CANL 2.135,1.667 2.573,1.885 0.438,0.219 10 false CANH 0.51,1.313 0.948,1.531 0.438,0.219 10 false ESS 2.646,1.313 3.083,1.531 0.438,0.219 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the steering sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G205-3 (CANH) - G205-2 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G205-3 (CANH) - G205-1 (ESS) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G205-2 (CANL) - G205-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G205-3 (CANH) - G205-5 (BAT) G - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G205-2 (CANL) - G205-5 (BAT) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4 WHEEL DRIVE CONTROL ECU (4WD CONTROL ECU)


Refer to Terminals of ECU.

Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>TRANSFER SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4 wheel drive control ECU (4WD control ECU) connectors.

C382831C01
2.167,0.083 2.604,0.313 0.438,0.229 5.292,0.177 5.729,0.406 0.438,0.229 3.5,0.906 3.771,0.406 3.771,0.406 3.938,0.406 true 3.51,1.104 3.74,1.469 3.74,1.469 3.906,1.469 true 1.115,1.094 0.979,1.365 0.979,1.365 0.781,1.365 true 5.948,1.073 6.177,1.438 6.177,1.438 6.344,1.438 true 0.125,0.063 0.438,0.26 0.313,0.198 10 false *a 2.25,0.115 2.563,0.313 0.313,0.198 10 false G53 5.396,0.219 5.708,0.417 0.313,0.198 10 false G54 3.979,0.333 4.417,0.531 0.438,0.198 10 false CANH 3.958,1.385 4.396,1.583 0.438,0.198 10 false CANL 0.542,1.292 0.979,1.49 0.438,0.198 10 false +B 6.396,1.354 6.833,1.552 0.438,0.198 10 false GND
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU [4WD Control ECU])
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G53-20 (CANH) - G53-40 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G53-20 (CANH) - G54-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G53-40 (CANL) - G54-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G53-20 (CANH) - G53-21 (+B) G - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G53-40 (CANL) - G53-21 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




FRONT POWER SEAT SWITCH (POWER SEAT CONTROL ECU) (w/ Seat Memory)


Refer to Terminals of ECU.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C375780C15
0.24,2.333 0.656,2.583 0.417,0.25 0.313,0.677 0.729,0.927 0.417,0.25 0.25,2.031 0.667,2.281 0.417,0.25 0.313,0.99 0.729,1.24 0.417,0.25 0.969,1.438 1.135,1.438 1.135,1.438 1.417,0.979 true 0.979,0.219 1.146,0.219 1.146,0.219 1.396,0.75 true 0.99,2.979 1.156,2.979 1.156,2.979 1.323,2.656 true 1.771,3 1.604,3 1.604,3 1.51,2.656 true 0.438,0.719 0.896,0.917 0.458,0.198 10 false a4 0.354,2.385 0.813,2.583 0.458,0.198 10 false b5 0.583,2.896 1.042,3.094 0.458,0.198 10 false CANN 0.635,0.146 1.094,0.344 0.458,0.198 10 false GND 1.844,2.938 2.302,3.135 0.458,0.198 10 false CANP 0.75,1.354 1.208,1.552 0.458,0.198 10 false +B 0.365,2.073 0.823,2.271 0.458,0.198 10 false a5 0.74,2.073 1.198,2.271 0.458,0.198 10 false *A 0.75,2.396 1.208,2.594 0.458,0.198 10 false *B 0.771,0.729 1.229,0.927 0.458,0.198 10 false *A 0.448,1.031 0.906,1.229 0.458,0.198 10 false b4 0.792,1.01 1.25,1.208 0.458,0.198 10 false *B 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to Front Power Seat Switch [Power Seat Control ECU])


Disconnect the front power seat switch (power seat control ECU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
a5-8 (CANP) - a5-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
a5-8 (CANP) - a4-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
a5-7 (CANN) - a4-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
a5-8 (CANP) - a4-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
a5-7 (CANN) - a4-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
b5-8 (CANP) - b5-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
b5-8 (CANP) - b4-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
b5-7 (CANN) - b4-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
b5-8 (CANP) - b4-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
b5-7 (CANN) - b4-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MULTIPLEX TILT AND TELESCOPIC ECU (w/ Seat Memory)


Refer to Terminals of ECU.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369151C17
1.5,0.333 1.917,0.583 0.417,0.25 1.208,2.063 1.323,2.521 1.323,2.521 1.49,2.521 true 0.625,1.74 0.906,0.823 0.906,0.823 1.073,0.823 true 0.813,1.729 1.073,1 1.073,1 1.24,1 true 1.229,1.74 1.406,1.229 1.406,1.229 1.573,1.229 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1.563,0.385 2,0.594 0.438,0.208 10 false G211 1.125,0.729 1.552,0.938 0.427,0.208 10 false GND 1.302,0.906 1.729,1.115 0.427,0.208 10 false +B 1.531,2.448 1.958,2.656 0.427,0.208 10 false CANN 1.625,1.146 2.052,1.354 0.427,0.208 10 false CANP
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


Disconnect the multiplex tilt and telescopic ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G211-3 (CANP) - G211-11 (CANN) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G211-3 (CANP) - G211-1 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G211-11 (CANN) - G211-1 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G211-3 (CANP) - G211-2 (+B) GR - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G211-11 (CANN) - G211-2 (+B) W - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

for Halogen Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>TERMINALS OF ECU

for LED Headlight: Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connectors.

C379615C04
5.688,0.323 6.156,0.573 0.469,0.25 3.375,0.302 3.844,0.552 0.469,0.25 1.031,0.281 1.5,0.531 0.469,0.25 0.74,2.135 0.906,2.135 0.906,2.135 1.052,1.469 true 0.833,2.333 1,2.333 1,2.333 1.156,1.479 true 4.177,2.333 3.969,2.333 3.969,2.333 3.781,1.479 true 3.375,2.344 3.542,2.344 3.542,2.344 3.698,1.49 true 6.406,1.969 6.198,1.969 6.198,1.969 6.385,1.573 true 5.552,0.833 5.76,0.833 5.76,0.833 5.906,1.24 true 0.344,0.271 0.656,0.469 0.313,0.198 10 false *a 4.854,0.354 5.167,0.552 0.313,0.198 10 false *b 5.792,0.365 6.104,0.563 0.313,0.198 10 false G48 3.469,0.365 3.844,0.583 0.375,0.219 10 false G218 1.115,0.323 1.542,0.573 0.427,0.25 10 false G216 0.313,2.042 0.76,2.26 0.448,0.219 10 false CANP 0.427,2.26 0.875,2.479 0.448,0.219 10 false CANN 2.99,2.281 3.438,2.5 0.448,0.219 10 false CANL 4.219,2.25 4.667,2.469 0.448,0.219 10 false CANH 6.49,1.896 6.938,2.115 0.448,0.219 10 false BAT 5.313,0.75 5.76,0.969 0.448,0.219 10 false CG
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G218-14 (CANH) - G218-13 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G218-14 (CANH) - G48-4 (CG) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G218-13 (CANL) - G48-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G218-14 (CANH) - G48-16 (BAT) L - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G218-13 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for Sub Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G216-9 (CANP) - G216-10 (CANN) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G216-9 (CANP) - G48-4 (CG) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G216-10 (CANN) - G48-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G216-9 (CANP) - G48-16 (BAT) P - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G216-10 (CANN) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Reverse Shift-linked Mirror)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
U165531C07
1.302,1.26 1.073,1.458 1.073,1.458 0.885,1.458 false 1.156,1.813 1.385,1.813 1.385,1.813 1.438,1.26 false 2.198,0.948 2.469,0.604 2.469,0.604 2.604,0.604 false 2.021,0.979 2.24,0.333 2.24,0.333 2.385,0.333 false 0.656,1.708 1.229,1.927 0.573,0.219 10 false CANP 0.365,1.375 0.969,1.594 0.604,0.219 10 false CANN 0.104,0.073 0.604,0.24 0.5,0.167 10 false *a 2.635,0.521 3.198,0.865 0.563,0.344 10 false GND 2.427,0.229 3.177,0.469 0.75,0.24 10 false CPUB 0.542,0.76 1.146,0.979 0.604,0.219 10 false K12
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


Disconnect the outer mirror control ECU assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K12-9 (CANP) - K12-8 (CANN) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
K12-9 (CANP) - K12-7 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
K12-8 (CANN) - K12-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
K12-9 (CANP) - K12-6 (CPUB) R - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
K12-8 (CANN) - K12-6 (CPUB) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Reverse Shift-linked Mirror)


Refer to Terminals of ECU.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
U165531C08
1.302,1.26 1.073,1.458 1.073,1.458 0.885,1.458 false 1.156,1.813 1.385,1.813 1.385,1.813 1.438,1.26 false 2.198,0.948 2.469,0.604 2.469,0.604 2.604,0.604 false 2.021,0.979 2.24,0.333 2.24,0.333 2.385,0.333 false 0.656,1.708 1.229,1.927 0.573,0.219 10 false CANP 0.365,1.375 0.969,1.594 0.604,0.219 10 false CANN 0.104,0.073 0.604,0.24 0.5,0.167 10 false *a 0.542,0.74 0.813,0.938 0.271,0.198 10 false J12 2.635,0.521 3.198,0.865 0.563,0.344 10 false GND 2.427,0.229 3.177,0.469 0.75,0.24 10 false CPUB
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Disconnect the outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J12-9 (CANP) - J12-8 (CANN) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
J12-9 (CANP) - J12-7 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J12-8 (CANN) - J12-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
J12-9 (CANP) - J12-6 (CPUB) G - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
J12-8 (CANN) - J12-6 (CPUB) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM (w/ VSC)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379614C03
0.24,0.99 0.594,1.188 0.354,0.198 0.167,2.333 0.521,2.531 0.354,0.198 0.833,1.792 1.021,1.792 1.021,1.792 1.125,1.271 true 1.542,0.333 1.375,0.333 1.375,0.333 1.302,1.135 true 1.635,1.771 1.469,1.771 1.469,1.771 1.469,1.271 true 2.427,3.188 2.26,3.188 2.26,3.188 2.26,2.688 true 0.354,0.135 0.667,0.333 0.313,0.198 10 false *a 0.427,1.729 0.938,1.938 0.51,0.208 10 false CANH 1.583,0.26 2.094,0.469 0.51,0.208 10 false CANL 1.688,1.698 2.198,1.906 0.51,0.208 10 false GND 0.26,1.01 0.771,1.219 0.51,0.208 10 false G46 0.229,2.365 0.74,2.573 0.51,0.208 10 false G48 2.479,3.115 2.99,3.323 0.51,0.208 10 false BAT 0.25,2.01 0.563,2.208 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


Disconnect the power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G46-1 (CANH) - G46-3 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G46-2 (CANL) - G46-3 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G46-1 (CANH) - G48-16 (BAT) L - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G46-2 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




SUSPENSION CONTROL ECU (w/ Air Suspension System)


Refer to Terminals of ECU.

Click hereSuspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>TEST MODE PROCEDURE

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379586C02
1.406,0.281 1.854,0.521 0.448,0.24 0.5,2.583 0.667,2.583 0.667,2.583 0.833,1.865 true 0.698,2.917 0.865,2.917 0.865,2.917 1.031,2 true 0.917,0.74 1.083,0.74 1.083,0.74 1.5,1.438 true 2.333,0.667 2.167,0.667 2.167,0.667 2.167,1.417 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.083,2.5 0.615,2.698 0.531,0.198 10 false CANH 0.281,2.833 0.813,3.031 0.531,0.198 10 false CANL 0.75,0.656 1.281,0.854 0.531,0.198 10 false B 2.385,0.583 2.917,0.781 0.531,0.198 10 false GND 1.5,0.323 2.031,0.521 0.531,0.198 10 false A49
*a Front view of wire harness connector
(to Suspension Control ECU)


Disconnect the suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A49-7 (CANH) - A49-8 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A49-7 (CANH) - A49-5 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A49-8 (CANL) - A49-5 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A49-7 (CANH) - A49-3 (B) GR - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A49-8 (CANL) - A49-3 (B) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor Sensor)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the blind spot monitor sensor LH connector.

C350884C13
1.688,0.135 2.115,0.427 0.427,0.292 4.979,0.208 5.406,0.5 0.427,0.292 1.76,1.302 1.76,0.615 1.76,0.615 1.604,0.615 true 1.615,2.219 1.76,2.219 1.76,2.219 1.76,1.563 true 2.375,2.219 2.219,2.219 2.219,2.219 2.219,1.563 true 6,2.115 5.844,2.115 5.844,2.115 5.844,1.667 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.635,0.073 3.948,0.271 0.313,0.198 10 false *b 1.781,0.219 2.104,0.417 0.323,0.198 10 false R42 5.073,0.292 5.396,0.49 0.323,0.198 10 false G48 1.198,2.156 1.688,2.406 0.49,0.25 10 false CA1N 1.177,0.552 1.667,0.802 0.49,0.25 10 false CA1P 2.448,2.156 2.938,2.406 0.49,0.25 10 false BLGD 6.083,2.052 6.573,2.302 0.49,0.25 10 false BAT
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R42-2 (CA1P) - R42-7 (CA1N) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R42-2 (CA1P) - R42-10 (BLGD) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R42-7 (CA1N) - R42-10 (BLGD) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R42-2 (CA1P) - G48-16 (BAT) LG - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R42-7 (CA1N) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the forward recognition camera connector.

C350886C14
1.823,0.146 2.24,0.427 0.417,0.281 4.979,0.198 5.385,0.469 0.406,0.271 2.25,1.333 2.781,0.948 true 1.927,2.063 2.042,1.688 true 2.417,2.031 2.24,1.698 true 6.094,1.948 5.875,1.677 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *b 1.865,0.198 2.177,0.396 0.313,0.198 10 false W22 2.844,0.844 3.313,1.063 0.469,0.219 10 false CA1P 2.396,2.073 2.865,2.292 0.469,0.219 10 false CA1N 1.677,2.083 2.146,2.302 0.469,0.219 10 false GND 5.063,0.25 5.375,0.448 0.313,0.198 10 false G48 6.083,2 6.552,2.219 0.469,0.219 10 false BAT
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W22-5 (CA1P) - W22-11 (CA1N) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
W22-5 (CA1P) - W22-10 (GND) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W22-11 (CA1N) - W22-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W22-5 (CA1P) - G48-16 (BAT) GR - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
W22-11 (CA1N) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the millimeter wave radar sensor assembly connector.

C350887C15
4.99,0.208 5.354,0.479 0.365,0.271 1.74,0.115 2.146,0.385 0.406,0.271 0.99,1.344 1.688,1.344 true 6.063,1.958 5.875,1.667 true 2.458,0.656 2.125,1.26 true 1.646,0.646 1.854,1.26 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *b 1.25,0.542 1.729,0.75 0.479,0.208 10 false CA2L 2.51,0.552 2.99,0.76 0.479,0.208 10 false CA2H 0.531,1.281 1.01,1.49 0.479,0.208 10 false SGND 6.073,1.99 6.552,2.198 0.479,0.208 10 false BAT 5.052,0.26 5.375,0.458 0.323,0.198 10 false G48 1.792,0.167 2.177,0.375 0.385,0.208 10 false A100
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A100-3 (CA2H) - A100-2 (CA2L) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A100-3 (CA2H) - A100-1 (SGND) V - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A100-2 (CA2L) - A100-1 (SGND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A100-3 (CA2H) - G48-16 (BAT) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A100-2 (CA2L) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>TERMINALS OF ECU

a.
C277477C51
1.469,0.26 1.906,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.552,0.302 2.01,0.5 0.458,0.198 10 false H49 1.604,1.885 2.063,2.083 0.458,0.198 10 false H51 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H51-9 (CANH) - H49-7 (GND1) R - BR HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
H51-10 (CANL) - H49-7 (GND1) W - BR LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
H51-9 (CANH) - H49-4 (+B1) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H51-10 (CANL) - H49-4 (+B1) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>TERMINALS OF ECU

a.
C277477C50
1.469,0.26 1.906,0.5 0.438,0.24 1.51,1.844 1.948,2.083 0.438,0.24 2.115,1.49 1.865,1.49 1.865,1.49 1.677,1.156 true 2.625,0.708 2.375,0.708 2.375,0.708 2.177,0.865 true 2.542,3.146 2.292,3.146 2.292,3.146 2.021,2.656 true 1.906,2.656 1.677,3.146 1.677,3.146 1.417,3.146 true 2.156,1.406 2.698,1.635 0.542,0.229 10 false GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 false *a 1.542,0.302 2,0.5 0.458,0.198 10 false H54 1.604,1.885 2.063,2.083 0.458,0.198 10 false H56 2.667,0.625 3.208,0.854 0.542,0.229 10 false +B1 2.594,3.063 3.135,3.292 0.542,0.229 10 false CANL 1,3.073 1.542,3.302 0.542,0.229 10 false CANH
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H56-9 (CANH) - H54-7 (GND1) R - BR HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
H56-10 (CANL) - H54-7 (GND1) W - BR LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
H56-9 (CANH) - H54-4 (+B1) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H56-10 (CANL) - H54-4 (+B1) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)


Refer to Terminals of ECU.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369136C17
1.5,0.667 1.917,0.917 0.417,0.25 1,2.417 1.167,2.417 1.167,2.417 1.385,1.969 true 2.417,2.417 2.25,2.417 2.25,2.417 2.083,2 true 1.26,2.75 1.427,2.75 1.427,2.75 1.646,2 true 2.167,2.75 2,2.75 2,2.75 1.792,2.021 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.594,0.719 1.906,0.917 0.313,0.198 10 false R41 0.75,2.333 1.167,2.521 0.417,0.188 10 false +B 2.479,2.333 2.896,2.521 0.417,0.188 10 false GND 0.865,2.677 1.281,2.865 0.417,0.188 10 false CANH 2.219,2.677 2.635,2.865 0.417,0.188 10 false CANL
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/ Entry and Start System

*2: w/o Entry and Start System

R41-9 (CANH) - R41-10 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R41-9 (CANH) - R41-12 (GND) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R41-10 (CANL) - R41-12 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R41-9 (CANH) - R41-7 (+B) LG - V*1
LG - L*2
HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R41-10 (CANL) - R41-7 (+B) W - V*1
W - L*2
LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C300839C19
0.052,1.094 0.469,1.354 0.417,0.26 1.917,1.875 2.094,1.875 2.094,1.875 2.344,1.135 true 2.865,1.875 2.677,1.875 2.677,1.875 2.531,1.135 true 2.313,0.323 2.49,0.323 2.49,0.323 2.813,1.063 true 1.219,0.333 1.083,0.333 1.083,0.333 0.76,1.25 true 0.156,0.146 0.469,0.302 0.313,0.156 10 false *a 0.094,1.146 0.479,1.375 0.385,0.229 10 false G215 1.479,1.823 1.917,2.042 0.438,0.219 10 false CANH 2.927,1.813 3.344,2.073 0.417,0.26 10 false CANL 2.115,0.26 2.385,0.531 0.271,0.271 10 false +B 1.281,0.281 1.583,0.51 0.302,0.229 10 false E
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G215-7 (CANH) - G215-8 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G215-7 (CANH) - G215-11 (E) P - W-B HIGH-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G215-8 (CANL) - G215-11 (E) W - W-B LOW-level CAN bus line - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
G215-7 (CANH) - G215-10 (+B) P - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G215-8 (CANL) - G215-10 (+B) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369145C12
1.5,0.667 1.917,0.917 0.417,0.25 1.958,2.104 2.25,1.031 2.25,1.031 2.417,1.031 true 1.844,2.115 2.115,0.792 2.115,0.792 2.281,0.792 true 0.781,1.906 0.677,1.448 0.677,1.448 0.51,1.448 true 2.24,1.917 2.469,1.229 2.469,1.229 2.635,1.229 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.563,0.719 1.979,0.938 0.417,0.219 10 false G187 2.344,0.729 2.813,0.948 0.469,0.219 10 false CANP 2.49,0.948 2.958,1.167 0.469,0.219 10 false CANN 2.677,1.146 3.146,1.365 0.469,0.219 10 false E 0.292,1.375 0.76,1.594 0.469,0.219 10 false +B
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the Telematics Transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G187-15 (CANP) - G187-16 (CANN) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G187-15 (CANP) - G187-4 (E) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G187-16 (CANN) - G187-4 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G187-15 (CANP) - G187-1 (+B) P - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G187-16 (CANN) - G187-1 (+B) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Rear Television Camera Assembly [built-in ECU])


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the rear television camera assembly connector.

C295280C27
0.594,0.552 0.99,0.823 0.396,0.271 5.042,0.083 5.438,0.354 0.396,0.271 0.594,0.865 0.979,1.073 0.385,0.208 1.594,1.49 1.719,1.49 1.719,1.49 2.01,1.073 true 1.563,0.344 1.688,0.344 1.688,0.344 2.01,0.844 true 5.146,0.667 4.792,0.271 4.792,0.271 4.656,0.271 true 6.198,1.521 6.083,1.521 6.083,1.521 5.875,1.146 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.708,0.615 1.167,0.813 0.458,0.198 10 false X10 1.135,1.406 1.75,1.604 0.615,0.198 10 false CANH 1.125,0.26 1.74,0.458 0.615,0.198 10 false CANL 4.385,0.188 5,0.385 0.615,0.198 10 false CG 5.115,0.125 5.573,0.323 0.458,0.198 10 false G48 6.292,1.438 6.75,1.635 0.458,0.198 10 false BAT 0.719,0.896 1.177,1.094 0.458,0.198 10 false v3 1.052,0.615 1.51,0.813 0.458,0.198 10 false *A 1.052,0.875 1.51,1.073 0.458,0.198 10 false *B 3.75,0.115 4.063,0.313 0.313,0.198 10 false *b
*A w/o Tire Carrier *B w/ Tire Carrier
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Tire Carrier
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X10-4 (CANH) - X10-1 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
X10-4 (CANH) - G48-4 (CG) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X10-1 (CANL) - G48-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X10-4 (CANH) - G48-16 (BAT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
X10-1 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

w/ Tire Carrier
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
v3-4 (CANH) - v3-1 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
v3-4 (CANH) - G48-4 (CG) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
v3-1 (CANL) - G48-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
v3-4 (CANH) - G48-16 (BAT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
v3-1 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the driving support ECU assembly connector.

C350885C08
1.583,0.146 2.083,0.406 0.5,0.26 5.01,0.188 5.406,0.458 0.396,0.271 2.719,1.271 2.719,0.583 2.719,0.583 2.865,0.583 true 2.583,1.271 2.583,0.583 2.583,0.583 2.448,0.583 true 5.833,1.667 5.833,2.156 5.833,2.156 5.969,2.156 true 2.458,1.542 2.458,2.031 2.458,2.031 2.323,2.031 true 1.677,0.198 2.146,0.458 0.469,0.26 10 false G224 0.104,0.094 0.563,0.292 0.458,0.198 10 false *a 3.76,0.094 4.219,0.292 0.458,0.198 10 false *b 2.01,0.531 2.51,0.76 0.5,0.229 10 false CA2H 2.948,0.531 3.448,0.76 0.5,0.229 10 false CA2L 1.958,1.969 2.458,2.198 0.5,0.229 10 false GND 5.094,0.25 5.573,0.563 0.479,0.313 10 false G48 6.052,2.094 6.552,2.323 0.5,0.229 10 false BAT
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G224-10 (CA2H) - G224-11 (CA2L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G224-10 (CA2H) - G224-28 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G224-11 (CA2L) - G224-28 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G224-10 (CA2H) - G48-16 (BAT) G - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G224-11 (CA2L) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Parking Assist Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
U165665C01
0.698,2.958 0.875,2.958 0.875,2.958 1.063,2.438 false 1,2.438 0.677,2.698 0.677,2.698 0.552,2.698 false 1.24,0.875 0.979,0.76 0.979,0.76 0.844,0.76 false 2.219,0.865 2.49,0.75 2.49,0.75 2.615,0.75 false 0.083,0.042 0.26,0.198 0.177,0.156 10 false *a 2.521,0.229 2.771,0.417 0.25,0.188 10 false I6 0.031,2.615 0.5,2.75 0.469,0.135 10 false CANH 0.188,2.875 0.656,3.01 0.469,0.135 10 false CANL 2.677,0.677 3.146,0.813 0.469,0.135 10 false +B 0.344,0.688 0.813,0.823 0.469,0.135 10 false GND1 2.906,2.219 3.167,2.458 0.26,0.24 10 false I7
*a Rear view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I7-40 (CANH) - I7-39 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I7-40 (CANH) - I6-4 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I7-39 (CANL) - I6-4 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I7-40 (CANH) - I6-1 (+B) B - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I7-39 (CANL) - I6-1 (+B) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System [w/ Multi-display])


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the clearance warning ECU assembly connector.

C292374C04
1.667,0.094 2.115,0.313 0.448,0.219 4.823,0.052 5.25,0.354 0.427,0.302 1.667,0.365 2.115,0.552 0.448,0.188 2.813,0.875 2.927,0.344 2.927,0.344 3.01,0.344 true 1.667,1.51 1.771,1.51 1.771,1.51 1.958,1.01 true 2.917,0.875 3.125,0.698 3.125,0.698 3.219,0.698 true 5.667,1.167 5.99,1.583 5.99,1.583 6.104,1.583 true 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 3.542,0.135 3.854,0.333 0.313,0.198 10 false *b 1.729,0.125 2.188,0.323 0.458,0.198 10 false G228 3.292,0.604 3.604,0.802 0.313,0.198 10 false R2 3.073,0.25 3.385,0.448 0.313,0.198 10 false R1 1.531,1.417 1.688,1.615 0.156,0.198 10 false E 4.917,0.104 5.229,0.302 0.313,0.198 10 false G48 6.188,1.479 6.646,1.677 0.458,0.198 10 false BAT 1.833,0.385 2.292,0.583 0.458,0.198 10 false I9 2.167,0.115 2.479,0.313 0.313,0.198 10 false *A 2.188,0.365 2.5,0.563 0.313,0.198 10 false *B
*A for 8 Sensor Type *B for 4 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 8 Sensor Type
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G228-17 (R1) - G228-18 (R2) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G228-17 (R1) - G228-30 (E) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G228-18 (R2) - G228-30 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G228-17 (R1) - G48-16 (BAT) R - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G228-18 (R2) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for 4 Sensor Type
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I9-17 (R1) - I9-18 (R2) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I9-17 (R1) - I9-30 (E) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I9-18 (R2) - I9-30 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I9-17 (R1) - G48-16 (BAT) R - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I9-18 (R2) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STABILIZER CONTROL ECU (w/ Kinetic Dynamic Suspension System)


Refer to Terminals of ECU.

Click hereSuspension>SUSPENSION CONTROL>KINETIC DYNAMIC SUSPENSION SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the stabilizer control ECU connector.

C382828C01
2.323,0.052 2.781,0.25 0.458,0.198 5.24,0.135 5.698,0.333 0.458,0.198 6.25,1.417 6.083,1.417 6.083,1.417 5.927,0.979 true 1.917,1.5 2.083,1.5 2.083,1.5 2.406,1.042 true 2.781,1.563 2.948,1.563 2.948,1.563 3.135,1 true 3.521,1.531 3.354,1.531 3.354,1.531 3.281,1.01 true 1.042,0.094 1.354,0.292 0.313,0.198 10 false *a 4.448,0.146 4.76,0.344 0.313,0.198 10 false *b 5.354,0.156 5.667,0.354 0.313,0.198 10 false G48 2.375,0.063 2.781,0.292 0.406,0.229 10 false G123 6.292,1.344 6.688,1.573 0.396,0.229 10 false BAT 1.583,1.406 1.979,1.635 0.396,0.229 10 false GND 2.365,1.479 2.76,1.708 0.396,0.229 10 false CANL 3.583,1.448 4.104,1.677 0.521,0.229 10 false CANH
*a Front view of wire harness connector
(to Stabilizer Control ECU)
*b Front view of DLC3



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G123-29 (CANH) - G123-22 (GND) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G123-28 (CANL) - G123-22 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G123-29 (CANH) - G48-16 (BAT) V - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G123-28 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH (for LED Headlight)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
U171632C01
0.646,1.771 0.729,1.771 0.729,1.771 0.969,1.313 true 2.583,3.24 2.427,3.24 2.427,3.24 2.229,2.979 true 1.979,2.094 2.063,2.094 2.063,2.094 2.521,1.292 true 1.781,1.875 1.865,1.875 1.865,1.875 2.406,1.292 true 0.104,0.073 0.292,0.25 0.188,0.177 10 false *a 0.313,1.708 0.75,1.938 0.438,0.229 10 false GND 0.406,2.698 0.729,2.885 0.323,0.188 10 false G48 0.104,2.146 0.292,2.323 0.188,0.177 10 false *b 1.604,0.188 2.01,0.344 0.406,0.156 10 false A102 2.625,3.156 3.125,3.292 0.5,0.135 10 false BAT 1.375,1.802 1.813,2.031 0.438,0.229 10 false CANL 1.521,2.031 1.958,2.26 0.438,0.229 10 false CANH
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly LH)
*b Front view of DLC3


Disconnect the No. 1 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A102-24 (CANH) - A102-23 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A102-24 (CANH) - A102-12 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A102-23(CANL) - A102-12 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A102-24 (CANH) - G48-16 (BAT) P - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A102-23 (CANL) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BUS BUFFER ECU (w/ Bus Buffer ECU)


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C382829C01
0.427,0.917 0.854,1.115 0.427,0.198 0.333,2.438 0.76,2.635 0.427,0.198 2.625,3.167 2.458,3.167 2.458,3.167 2.292,2.833 true 2.583,1.333 2.417,1.333 2.417,1.333 2,1 true 2.417,0.333 2.25,0.333 2.25,0.333 1.833,0.917 true 1.969,1.938 1.802,1.938 1.802,1.938 1.667,2.396 true 0.125,0.188 0.438,0.385 0.313,0.198 10 false *a 0.177,1.552 0.49,1.75 0.313,0.198 10 false *b 2.698,3.094 3.01,3.292 0.313,0.198 10 false BAT 2.438,0.25 2.938,0.5 0.5,0.25 10 false CAN+ 2.625,1.26 3.125,1.51 0.5,0.25 10 false CAN- 0.479,0.948 0.979,1.198 0.5,0.25 10 false G199 0.417,2.479 0.917,2.729 0.5,0.25 10 false G48 2.021,1.865 2.333,2.063 0.313,0.198 10 false CG
*a Front view of wire harness connector
(to Bus Buffer ECU)
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G199-2 (CAN+) - G199-1 (CAN-) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G199-2 (CAN+) - G48-4 (CG) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G199-1 (CAN-) - G48-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
G199-2 (CAN+) - G48-16 (BAT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G199-1 (CAN-) - G48-16 (BAT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher