Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Condition Symptoms Trouble Area
Audio Receiver Assembly Communication Stop Mode Any of the following conditions are met:
·

"Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Radio and display receiver assembly CAN branch wire or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C289528E19
1.781,3.604 3.063,3.823 1.281,0.219 10 false from IG NO.1 Relay 5.24,1.208 5.448,1.396 0.208,0.188 10 false 10 5.271,0.625 5.427,0.854 0.156,0.229 10 false 9 5.271,3.958 5.375,4.094 0.104,0.135 10 false 7 5.271,3.365 5.396,3.531 0.125,0.167 10 false 1 5.177,0.844 5.552,1.073 0.375,0.229 10 false H51 5.177,1.427 5.531,1.625 0.354,0.198 10 false H51 5.177,3.594 5.531,3.813 0.354,0.219 10 false H51 5.177,4.167 5.5,4.375 0.323,0.208 10 false H49 5.625,1.438 6.24,1.646 0.615,0.208 10 false CANL 5.625,0.844 6.24,1.042 0.615,0.198 10 false CANH 5.625,3.594 6.24,3.792 0.615,0.198 10 false IG 5.625,4.188 6.26,4.375 0.635,0.188 10 false GND1 0.427,1.771 1.385,1.958 0.958,0.188 10 false G289 0.427,1.917 2.104,2.135 1.677,0.219 10 false No. 5 Junction Connector 1.594,1.323 1.854,1.552 0.26,0.229 10 false 14 1.594,0.74 1.792,0.875 0.198,0.135 10 false 3 5.271,2.771 5.406,2.938 0.135,0.167 10 false 3 5.167,3 5.49,3.198 0.323,0.198 10 false H49 5.625,3.01 6.229,3.24 0.604,0.229 10 false ACC1 2.042,3.01 3.094,3.281 1.052,0.271 10 false from ACC Relay 5.177,2.417 5.531,2.594 0.354,0.177 10 false H49 5.271,2.188 5.417,2.365 0.146,0.177 10 false 4 5.625,2.427 6.24,2.625 0.615,0.198 10 false +B1 2.281,2.427 3.104,2.667 0.823,0.24 10 false from Battery 3.948,2.292 4.802,2.583 0.854,0.292 10 false RAD NO.1 4.104,2.885 4.927,3.104 0.823,0.219 10 false ACC 3.833,3.458 4.823,3.688 0.99,0.229 10 false ECU-IG NO.2 5.208,4.906 6.938,5.302 1.729,0.396 10 false Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U148880C01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.58,0.371 1.854,0.512 0.274,0.140 10 H51 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U148930C01
0.064,0.06 0.269,0.230 0.205,0.170 10 *a 2.01,0.866 2.297,0.554 2.297,0.554 2.402,0.554 false 2.184,0.98 2.383,1.19 2.383,1.19 2.488,1.19 false 1.599,1.152 1.351,1.459 1.351,1.459 1.246,1.459 false 0.449,2.359 0.613,2.498 0.165,0.139 10 IG 0.743,1.384 1.154,1.522 0.411,0.139 10 GND1 2.505,1.113 2.916,1.251 0.411,0.139 10 +B1 2.423,0.477 2.835,0.615 0.411,0.139 10 ACC1 0.651,2.432 0.786,2.432 0.786,2.432 0.981,2.605 false 1.577,1.826 1.857,1.963 0.279,0.137 10 H51 1.575,0.256 1.854,0.393 0.279,0.137 10 H49
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H49-7 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H49-4 (+B1) - Body ground Always 11 to 14 V
H49-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
H51-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)