Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Any of the following conditions are met:
·

"Clearance Warning (Clearance Sensor)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Clearance warning ECU assembly branch wire or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

C393735E01
5.396,3.865 6.604,4.438 1.208,0.573 10 false Clearance Warning ECU Assembly 5.385,3.688 6.5,3.927 1.115,0.24 10 false G228*1, I9*2 5.594,3.188 5.969,3.365 0.375,0.177 10 false E 5.604,2.604 5.979,2.781 0.375,0.177 10 false IG 5.615,1.135 6.073,1.333 0.458,0.198 10 false R1 5.604,1.729 6.063,1.927 0.458,0.198 10 false R2 5.344,1.021 5.625,1.24 0.281,0.219 10 false 17 5.333,1.625 5.573,1.802 0.24,0.177 10 false 18 5.344,3.083 5.656,3.271 0.313,0.188 10 false 30 5.396,2.5 5.667,2.708 0.271,0.208 10 false 1 3.083,2.417 4.208,2.646 1.125,0.229 10 false ECU-IG NO.2 1.156,2.573 2.698,2.948 1.542,0.375 10 false from IG NO.1 Relay 0.188,2.042 2.563,2.26 2.375,0.219 10 false No. 7 CAN Junction Connector*1, *2 1.635,1.115 2.031,1.302 0.396,0.188 10 false G291 1.708,0.917 2,1.125 0.292,0.208 10 false 5*1 1.667,1.5 2,1.677 0.333,0.177 10 false 15*1 0.26,4.344 1.875,4.688 1.615,0.344 10 false *3: for RHD 4 Sensor Type 0.26,4.031 1.875,4.375 1.615,0.344 10 false *2: for RHD 8 Sensor Type 2.125,0.917 2.417,1.104 0.292,0.188 10 false 7*2 2.073,1.51 2.406,1.688 0.333,0.177 10 false 17*2 2.531,0.927 2.823,1.135 0.292,0.208 10 false 5*3 2.5,1.5 2.833,1.677 0.333,0.177 10 false 15*3 1.646,1.698 2.042,1.885 0.396,0.188 10 false G291 2.063,1.104 2.458,1.292 0.396,0.188 10 false G291 2.042,1.698 2.438,1.885 0.396,0.188 10 false G291 2.458,1.104 2.854,1.292 0.396,0.188 10 false G287 2.469,1.698 2.865,1.885 0.396,0.188 10 false G287 0.188,2.25 2.292,2.5 2.104,0.25 10 false No. 3 CAN Junction Connector*3 0.26,3.74 1.875,4.083 1.615,0.344 10 false *1: for LHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369149C08
1.5,0.531 1.917,0.781 0.417,0.25 1.5,0.208 1.917,0.458 0.417,0.25 2.5,1 2.667,1 2.667,1 3.01,1.604 true 2.583,0.833 2.75,0.833 2.75,0.833 3.167,1.583 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 2.313,0.938 2.625,1.135 0.313,0.198 10 false R1 2.406,0.76 2.719,0.958 0.313,0.198 10 false R2 1.552,0.25 1.948,0.479 0.396,0.229 10 false G228 1.656,0.573 1.958,0.802 0.302,0.229 10 false I9 1.969,0.25 2.365,0.479 0.396,0.229 10 false *A 1.979,0.563 2.375,0.792 0.396,0.229 10 false *B
*A for 8 Sensor Type
*B for 4 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 8 Sensor Type
Tester Connection Condition Specified Condition
G228-17 (R1) - G228-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

for 4 Sensor Type
Tester Connection Condition Specified Condition
I9-17 (R1) - I9-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369149C09
1.5,0.521 1.917,0.771 0.417,0.25 1.5,0.198 1.917,0.448 0.417,0.25 1.604,2.563 1.771,2.563 1.771,2.563 1.771,1.813 true 0.438,0.667 0.271,0.667 0.271,0.667 0.271,1.583 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.448,2.49 1.76,2.688 0.313,0.198 10 false E 0.542,0.604 0.854,0.802 0.313,0.198 10 false IG 1.656,0.573 1.917,0.771 0.26,0.198 10 false I9 1.552,0.25 1.917,0.448 0.365,0.198 10 false G228 1.969,0.25 2.333,0.448 0.365,0.198 10 false *A 1.979,0.573 2.344,0.771 0.365,0.198 10 false *B
*A for 8 Sensor Type
*B for 4 Sensor Type
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 8 Sensor Type
Tester Connection Condition Specified Condition
G228-30 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

for 4 Sensor Type
Tester Connection Condition Specified Condition
I9-30 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 8 Sensor Type
Tester Connection Switch Condition Specified Condition
G228-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

for 4 Sensor Type
Tester Connection Switch Condition Specified Condition
I9-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)