Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  DCM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
DCM Communication Stop Mode Any of the following conditions are met:
·

"DCM" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "DCM Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Telematics transceiver branch wire or connector

·

Power source circuit of telematics transceiver

·

Telematics transceiver ground circuit

·

Telematics transceiver



WIRING DIAGRAM

C369088E11
5.656,1.01 6.271,1.208 0.615,0.198 10 false CANP 5.656,1.542 6.271,1.74 0.615,0.198 10 false CANN 5.646,2.385 6.26,2.583 0.615,0.198 10 false +B 5.646,3.146 6.26,3.344 0.615,0.198 10 false ACC 5.646,3.865 6.26,4.063 0.615,0.198 10 false IG2 5.646,4.427 6.26,4.625 0.615,0.198 10 false E 4.188,2.24 4.802,2.438 0.615,0.198 10 false DCM 1.552,0.885 2.167,1.083 0.615,0.198 10 false 4 1.521,1.396 2.135,1.594 0.615,0.198 10 false 15 5.375,0.896 5.99,1.094 0.615,0.198 10 false 15 5.365,1.417 5.979,1.615 0.615,0.198 10 false 16 5.458,2.25 6.073,2.448 0.615,0.198 10 false 1 5.448,3.021 6.063,3.219 0.615,0.198 10 false 8 5.448,3.75 6.063,3.948 0.615,0.198 10 false 7 5.448,4.302 6.063,4.5 0.615,0.198 10 false 4 5.208,4.854 5.823,5.052 0.615,0.198 10 false G187 5.219,5.031 6.958,5.438 1.74,0.406 10 false Telematics Transceiver 0.156,1.802 0.771,2 0.615,0.198 10 false G289 0.146,1.979 2.208,2.542 2.063,0.563 10 false No. 5 CAN Junction Connector 4.219,3.719 4.823,4.135 0.604,0.417 10 false IGN 4.188,3.01 4.802,3.208 0.615,0.198 10 false ACC 2.271,2.365 3.208,2.688 0.938,0.323 10 false from Battery 2.052,3.115 3.177,3.438 1.125,0.323 10 false from ACC Relay 2.135,3.833 3.208,4.281 1.073,0.448 10 false from IG2 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TELEMATICS TRANSCEIVER BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
U156361C01
1.115,1.802 1.292,1.802 1.292,1.802 1.823,1.167 true 2.292,1.802 2.125,1.802 2.125,1.802 1.906,1.167 true 0.094,0.073 0.531,0.417 0.438,0.344 10 false *a 1.531,0.271 1.958,0.521 0.427,0.25 10 false G187 0.635,1.729 1.115,1.938 0.479,0.208 10 false CANP 2.365,1.719 2.969,1.969 0.604,0.25 10 false CANN
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-15 (CANP) - G187-16 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U156362C01
0.438,1.458 0.604,1.458 0.604,1.458 0.948,1.167 true 2.854,0.698 2.698,0.698 2.698,0.698 2.271,0.927 true 0.479,0.635 0.635,0.635 0.635,0.635 0.969,0.938 true 0.656,1.74 0.823,1.74 0.823,1.74 1.052,1.188 true 0.115,0.104 0.552,0.448 0.438,0.344 10 false *a 1.531,0.26 1.927,0.448 0.396,0.188 10 false G187 2.885,0.604 3.042,0.75 0.156,0.146 10 false E 0.219,0.563 0.479,0.708 0.26,0.146 10 false +B 0.281,1.677 0.604,1.823 0.323,0.146 10 false ACC 0.115,1.375 0.438,1.521 0.323,0.146 10 false IG2
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-4 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G187-1 (+B) - Body ground Always 11 to 14 V
G187-8 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G187-7 (IG2) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)