Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Driving Support ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Driving Support ECU Communication Stop Mode Any of the following conditions are met:
·

"Driving Support (Cruise Control-ACC)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Driving Support ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Driving support ECU assembly branch wire or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly



WIRING DIAGRAM

C368272E09
5.615,0.885 6.229,1.083 0.615,0.198 10 false CA2H 5.625,1.469 6.24,1.667 0.615,0.198 10 false CA2L 5.604,3.073 6.219,3.271 0.615,0.198 10 false GND 5.615,2.49 6.229,2.688 0.615,0.198 10 false B 1.792,2.469 3.146,2.792 1.354,0.323 10 false from IG NO.1 Relay 5.354,2.385 5.969,2.583 0.615,0.198 10 false 7 5.323,2.969 5.938,3.167 0.615,0.198 10 false 28 5.354,1.375 5.969,1.573 0.615,0.198 10 false 11 5.333,0.781 5.948,0.979 0.615,0.198 10 false 10 1.646,0.792 2.26,0.99 0.615,0.198 10 false 4 1.635,1.375 2.25,1.573 0.615,0.198 10 false 14 5.177,4.042 5.792,4.24 0.615,0.198 10 false G224 5.156,4.219 7.156,4.594 2,0.375 10 false Driving Support ECU Assembly 0.177,1.875 2.24,2.333 2.063,0.458 10 false No. 7 CAN Junction Connector 0.177,1.708 0.792,1.906 0.615,0.198 10 false G291 3.771,2.333 4.802,2.563 1.031,0.229 10 false ECU-IG NO.1

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (DRIVING SUPPORT ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C346990C55
1.51,0.406 1.958,0.646 0.448,0.24 2.448,0.896 2.615,0.896 2.615,0.896 2.615,1.792 true 2.927,0.896 2.771,0.896 2.771,0.896 2.771,1.792 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.573,0.448 2.083,0.677 0.51,0.229 10 false G224 2.052,0.833 2.51,0.99 0.458,0.156 10 false CA2H 2.969,0.833 3.427,0.99 0.458,0.156 10 false CA2L
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-10 (CA2H) - G224-11 (CA2L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346990C56
1.51,0.406 1.958,0.646 0.448,0.24 1.052,0.906 1.219,0.906 1.219,0.906 1.219,1.802 true 2.646,2.75 2.479,2.75 2.479,2.75 2.479,2.094 true 0.083,0.115 0.396,0.271 0.313,0.156 10 false *a 1.573,0.448 2,0.625 0.427,0.177 10 false G224 0.917,0.854 1.135,1.01 0.219,0.156 10 false B 2.698,2.688 3.156,2.844 0.458,0.156 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G224-28 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G224-7 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)