Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for LED Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261295 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Headlight)  DISASSEMBLY  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>PRECAUTION

·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



Hide 81510C 2.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E375368C01
1.708,0.76 2.896,0.76 true 0.688,2.781 1.458,3.323 true 2.969,0.667 3.281,0.823 0.313,0.156 10 false *a 0.51,2.667 0.823,2.823 0.313,0.156 10 false *b
*a Matchmark
*b Unlock Position Mark


Turn the bulb socket counterclockwise until the matchmark is aligned with the unlock position mark to disconnect the bulb socket.


b.
E375370

Remove the front turn signal light bulb from the bulb socket.


Hide 81056 3.REMOVE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

Hide 81134 4.REMOVE HEADLIGHT GASKET

Hide 52134J 5.REMOVE FRONT BUMPER BAR REINFORCEMENT LH

a.
E375371

Remove the 2 screws and front bumper bar reinforcement LH.


Hide 81192 6.REMOVE HEADLIGHT SEAL

a.
E375373

Remove the headlight seal.

NOTICE:

The headlight seal must not be reused.



Hide 53246B 7.REMOVE HEADLIGHT BRACKET LH

a.
E375372

Remove the 7 screws.


b.

Detach the claw and remove the headlight bracket LH.


Hide 81171C 8.REMOVE HEADLIGHT LENS LH

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.

Remove the 7 screws.


b.

Using a T20H "TORX" driver, remove the "TORX" screw.

E375382C01
5.021,1.333 5.333,1.49 0.313,0.156 10 false *a
*a "TORX" Screw - -



c.
E375379C01
2.24,1.594 1.448,1.094 true 1.458,3.979 0.948,3.719 true 2.302,1.542 2.615,1.698 0.313,0.156 10 false *a 0.771,3.615 1.083,3.771 0.313,0.156 10 false *b
*a Matchmark
*b Unlock Position Mark


Turn the connector cover counterclockwise until the matchmark is aligned with the unlock position mark to remove the connector cover.


d.
E376442

Disconnect the connector.


e.

Remove the headlight lens LH:

HINT:

Remove the headlight lens LH from the headlight housing from the separation starting point toward the base point claw as shown in the illustration.

E375384C01
4.208,1.865 4.521,2.021 0.313,0.156 10 false *a
*a Base Point Claw - -
V100136

Separation Starting Point - -



i.

Detach the 7 claws.

HINT:

It is not necessary to detach the claw at the base point as the claw is detached in the later step.


E375383C01
4.083,3.427 4.396,3.583 0.313,0.156 10 false *a
*a Base Point Claw - -



ii.
E375386

Using a dryer, warm the headlight lens gasket from the backside of the headlight assembly LH at the separation starting point of the headlight lens LH.

NOTICE:

If the headlight is heated unevenly, it will deform or melt.



iii.

Insert a finger between the headlight lens LH and headlight housing and lift up the headlight lens LH.


iv.

Using a screwdriver, pull out the headlight lens gasket through the opening.

NOTICE:

Do not damage the groove in the headlight housing or the surface of the headlight lens LH.


HINT:

Tape the screwdriver tip before use.


E362745C01
0,0 0,0 false
V100144

Headlight Lens Gasket
V100145

Headlight Lens LH
V100146

Headlight Housing
V100155

Protective Tape



v.
E375387C01
1.781,0.583 2.094,0.74 0.313,0.156 10 false *a
*a Base Point Claw
V100155

Headlight Lens Gasket


While lifting up the headlight lens LH, pull out the headlight lens gasket until it reaches the base point claw.

HINT:

If the headlight lens gasket is disconnected while being pulled out, lift up the headlight lens and pull the headlight lens gasket again.



vi.

Detach the base point claw and remove the headlight lens LH.

E376346C01
4.198,1.792 4.51,1.948 0.313,0.156 10 false *a
*a Base Point Claw - -




Hide 81132B 9.REMOVE HEADLIGHT LENS GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.

Remove the remaining headlight lens gasket from the headlight lens and headlight housing.

E375388C01
0.146,0.198 0.542,0.51 0.396,0.313 12 false *A 3.823,0.188 4.219,0.5 0.396,0.313 12 false *B
*A Headlight Housing Side *B Headlight Lens LH Side
V100155

Headlight Lens Gasket - -



Hide 81175 10.REMOVE HEADLIGHT UNIT ASSEMBLY LH

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the headlight unit assembly LH with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.

Using a vernier caliper, measure and record the dimensions of the protrusion and retraction of the aiming screw.

E376443C01
0.979,1.49 1.292,1.646 0.313,0.156 10 false *a 6,2.031 6.229,2.229 0.229,0.198 10 true *a
*a Protrusion and Retraction Amount Measurement Area - -



b.
E376444

Disconnect the connector.


c.
E376445

While holding the headlight unit assembly LH with one hand so that it does not fall over, loosen the vertical aiming screw and horizontal aiming screw until the headlight unit assembly LH is disconnected.


d.

Lift up the bottom side of the headlight unit assembly LH and disconnect and remove it from the headlight leveling motor LH as shown in the illustration.

E376446


Hide 85662 11.REMOVE HEADLIGHT LEVELING MOTOR LH

a.
E375396

Disconnect the connector.


b.
E375397

Turn the headlight leveling motor LH counterclockwise until it stops and remove the headlight leveling motor LH.

HINT:

For the headlight assembly RH, turn the headlight leveling motor RH clockwise to remove it.



Hide 85669 12.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.
E282556

Remove the headlight leveling motor base packing.

NOTICE:

The headlight leveling motor base packing must not be reused.