Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for LED Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0261295 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Headlight)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 85669 1.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Install a new headlight leveling motor base packing.


Hide 85662 2.INSTALL HEADLIGHT LEVELING MOTOR LH

a.
E375398

Insert and turn the headlight leveling motor LH until it stops to install it.

HINT:

For the headlight assembly RH, turn the headlight leveling motor RH counterclockwise to install it.



b.

Connect the connector.


Hide 81175 3.INSTALL HEADLIGHT UNIT ASSEMBLY LH

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the headlight unit assembly LH with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.

Set the both rail, beam axis horizontal and vertical adjustment aiming screws for the headlight unit assembly LH.

HINT:

Align and set them according to the white and black arrows shown in the illustration.


E376447


b.
E376448

While holding the headlight unit assembly LH with one hand so that it does not fall over, tighten the vertical aiming screw and horizontal aiming screw 20 rotations.


c.

Push the headlight unit assembly LH to connect the headlight leveling motor LH.

E376449


d.
E376448

Tighten the vertical aiming screw and horizontal aiming screw until the protrusion and retraction amount is the same as that recorded.


e.
E376444

Connect the connector.


Hide 81132B 4.INSTALL HEADLIGHT LENS GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are fingerprints on the inner surface of the lens, lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E376348C01
0,0 0,0 false
V100155

Area to Clean


Clean the headlight lens gasket installation groove.


b.

Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.

HINT:

Use the peeling paper that is supplied with the headlight lens gasket.



c.
E318045

Using scissors, cut the headlight lens gasket at a 90°.


d.
E376349C01
0,0 0,0 false
V100143

Starting Point


Starting from the position shown in the illustration, set the headlight lens gasket into the straight groove clockwise until it meets the corner groove.

HINT:

Lightly set the gasket in place without pulling.



e.
E376350C01
0,0 0,0 false
V100136

Corner Groove
V100145

Headlight Lens Gasket
V100155

Peeling Paper


Set the headlight lens gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.

NOTICE:
·

Lightly set the gasket in place without pulling.

·

If the headlight lens gasket is set while pulled, the gasket will be pushed up at the corner groove.




f.

Repeat the following order while working in a circle back to the starting point.

i.

Set headlight lens gasket into straight groove.


ii.

Push into bottom of groove.


iii.

Set into corner groove.


iv.

Push into bottom of groove.



g.
E376351C01
1.188,2.583 1.5,2.74 0.313,0.156 10 false *a
*a 20 mm (0.79 in.)
V100136

Corner Groove


Using scissors, cut the headlight lens gasket at a 45°angle at the starting point so that the gasket overlaps itself 20 mm (0.79 in.) and set the gasket in place.


h.

Check the installation condition of the headlight lens gasket.

OK:

Gasket not pushed up or protruding.

No gap where gasket overlaps.


NOTICE:

Check the corners carefully since the gasket can easily become pushed up in those areas.



Hide 81171C 5.INSTALL HEADLIGHT LENS LH

NOTICE:
·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Perform work using clean rubber gloves.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E376352C01
0,0 0,0 false
V100155

Area to Clean


Clean the headlight lens gasket contact surface.


b.

Set the headlight lens LH in place.

NOTICE:
E317610C01
0,0 0,0 false
V100144

Headlight Lens Gasket
V100146

Head Light Housing
V100155

Headlight Lens LH


Set the headlight lens LH in the middle of the headlight lens gasket as shown in the illustration.



c.

Check that the entire circumference of the headlight lens LH is positioned above the middle of the headlight lens gasket.


d.

Attach the base point claw.

HINT:

Install the headlight lens LH from the installation starting point shown in the illustration.

E375385C01
4.365,1.708 4.573,1.854 0.208,0.146 10 true *a
*a Base Point Claw - -
V100136

Installation Starting Point - -




e.

Attach the remaining claw to install the headlight lens LH.

E376353


f.
E376442

Connect the connector.


g.
E375380C01
2.292,1.5 1.542,1.323 true 1.448,1.396 1.26,1.573 true 1.323,3.677 0.99,3.677 true 2.354,1.438 2.667,1.594 0.313,0.156 10 false *a 1.115,1.573 1.427,1.729 0.313,0.156 10 false *b 0.792,3.594 1.104,3.75 0.313,0.156 10 false *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark


Align the matchmark of the connector cover with the unlock position mark, and then rotate the connector cover clockwise until the lock position mark to install the connector cover.


h.

Using a T20H "TORX" driver, install the "TORX" screw.


i.

Install the 7 screws.

E375382C01
5.021,1.333 5.333,1.49 0.313,0.156 10 false *a
*a "TORX" Screw - -



j.

Check the condition of the headlight lens gasket.

OK:

Gasket contacts headlight lens LH and does not protrude out.



Hide 53246B 6.INSTALL HEADLIGHT BRACKET LH

a.

Attach the claw to install the headlight bracket LH.


b.

Install the 7 screws.


Hide 81192 7.INSTALL HEADLIGHT SEAL

a.
E376354C01
0,0 0,0 false
V100155

Area to Clean


Clean the application area as shown in the illustration.

NOTICE:

Remove any remaining double-sided tape, and then clean and degrease the area.



b.

Remove approximately 30 mm (1.18 in.) of the peeling tape from a new headlight seal.


c.
E375377C01
0.365,1.01 0.792,1.344 0.427,0.333 0.375,1.021 0.583,1.229 0.208,0.208 10 true *a
*a Alignment Line


Align the headlight seal with the alignment line and set it.


d.
E376355C01
0,0 0,0 false
V100145

Peeling Tape


While peeling the peeling tape, align the headlight seal to the curve and set it.


e.
E375378

Press the set portion of the part with your finger to secure it.

NOTICE:

Do not slide your finger horizontally, as doing so may stretch the part unnecessarily.



Hide 52134I 8.INSTALL FRONT BUMPER BAR REINFORCEMENT LH

a.

Install the front bumper bar reinforcement LH with the 2 screws.


Hide 81134 9.INSTALL HEADLIGHT GASKET

Hide 81056 10.INSTALL NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

Hide 81510C 11.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the bulb socket.


b.
E375369C01
1.458,0.719 0.323,0.615 true 1.698,3.24 2.417,2.792 true 2.948,0.448 1.521,0.813 true 3.01,0.354 3.323,0.51 0.313,0.156 10 false *a 0.115,0.521 0.427,0.677 0.313,0.156 10 false *b 2.458,2.688 2.771,2.844 0.313,0.156 10 false *c
*a Matchmark
*b Unlock Position Mark
*c Lock Position Mark


Align the matchmark of the bulb socket with the unlock position mark, and then rotate the bulb socket clockwise until the lock position mark to connect the bulb socket.