Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER › 2017.08–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260759 SHIFT LEVER A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 33530F 1.INSTALL SHIFT LEVER ASSEMBLY

NOTICE:

Check that the park/neutral position switch assembly and the shift lever are in N.


a.
C380127N01
2.521,1.5 2.656,1.708 0.135,0.208 10 true 1 0.719,0.25 0.854,0.458 0.135,0.208 10 true 2 2.469,0.24 2.604,0.448 0.135,0.208 10 true 3 0.688,1.313 0.833,1.5 0.146,0.188 10 true 4

Install the transmission floor shift assembly with the 4 bolts tighten the bolt in the order shown in the illustration.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Connect the 2 connectors.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Turn the socket of the transmission control cable assembly 180° counterclockwise. While holding the socket in place, push in the lock piece until the lock piece clicks twice.

C216621E02
1.617,1.223 1.617,1.453 1.617,1.453 1.853,1.453 false 1.56,0.543 1.56,0.328 1.56,0.328 1.326,0.328 false 1.875,1.381 2.046,1.536 0.171,0.155 10 *1 1.161,0.252 1.341,0.413 0.180,0.161 10 *2 3.706,0.101 3.887,0.262 0.180,0.161 10 *a

Text in Illustration
*1 Socket *2 Lock Piece
*a Push In - -

NOTICE:

Do not over-rotate the socket as it will come off the internal spring and the transmission control cable assembly will not be reusable.


HINT:

If the lock piece cannot be pushed in, slightly turn the socket clockwise and then push in the lock piece again.



b.

Install the outer part of the transmission control cable assembly to the transmission floor shift assembly retainer. Check that the socket and lock piece are positioned at original position.

C216998E01
0.747,1.444 0.932,1.612 0.185,0.168 10 *1 1.393,1.264 0.995,1.513 0.995,1.513 0.911,1.513 false

Text in Illustration
*1 Transmission Floor Shift Assembly Retainer - -


c.
C203381E01
1.358,0.382 1.530,0.547 0.171,0.165 10 *1 1.46,1.83 1.631,1.995 0.171,0.165 10 *1 2.491,1.697 2.700,1.881 0.209,0.184 10 *2 2.538,1.357 2.747,1.541 0.209,0.184 10 *2 1.814,1.007 1.672,0.481 1.672,0.481 1.574,0.481 false 1.846,2.23 1.762,1.92 1.762,1.92 1.665,1.92 false 2.452,2.097 2.368,1.787 2.368,1.787 2.466,1.787 false 2.34,1.133 2.424,1.443 2.424,1.443 2.521,1.443 false

Slide the slider in the direction shown in the illustration and pull out the lock piece.

Text in Illustration
*1 Slider
*2 Lock Piece


d.
C204586

Connect the end of the cable to the shift lever.

NOTICE:
·

The shift lever should be in N.

·

Make sure that the lock piece is pulled up.

·

Push on the end of the cable all the way to the base of the pin.




e.
U115849

Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.