Home › Drivetrain › VF4BM (TRANSFER / 4WD / AWD) › 4WD CONTROL SWITCH(w/o Combination Switch) › from 2017.08
RM27T0E _52 Drivetrain _053703 VF4BM TRANSFER / 4WD / AWD _0260843 4WD CONTROL SWITCH(w/o Combination Switch) G

VF4BM TRANSFER / 4WD / AWD  4WD CONTROL SWITCH(w/o Combination Switch)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84223A 1.INSPECT TRANSFER POSITION SWITCH

a.

Check the 4 wheel drive control ECU.

i.

Disconnect the switch connector.


ii.
C381466C07
1.417,1.708 1.583,1.708 1.583,1.708 1.583,1.208 true 2.135,1.719 1.969,1.719 1.969,1.719 1.969,1.219 true 0,0 0.313,0.156 0.313,0.156 10 false *a 2.188,1.635 2.5,1.833 0.313,0.198 10 false LO 1,1.625 1.417,1.833 0.417,0.208 10 false GND2
*a Component without harness connected
(4wd Control Switch)


for 2-MODE 4WD:

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (LO) - 4 (GND2) H4 10 kΩ or higher
L4 Below 1 Ω


If the result is not as specified, replace the 4wd control switch (Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>REMOVAL)


iii.
C381466C03
2.135,1.698 1.969,1.698 1.969,1.698 1.969,1.198 true 1.125,1.698 1.375,1.698 1.375,1.698 1.375,1.198 true 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a 2.208,1.615 2.521,1.813 0.313,0.198 10 false LO 0.906,1.615 1.219,1.813 0.313,0.198 10 false 2-4
*a Front view of wire harness connector
(to 4wd Control Switch)


for 3-MODE 4WD:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
2 (LO) - Body ground Ignition switch ON 10.5 to 14 V
5 (HI) - Body ground Ignition switch ON 10.5 to 14 V



iv.

Reconnect the 4wd control switch connector.


v.
C381466C08
1.208,1.771 1.375,1.771 1.375,1.771 1.375,1.188 false 2.125,1.771 1.958,1.771 1.958,1.771 1.958,1.188 false 1.583,1.75 1.583,1.198 false 0.948,1.698 1.26,1.896 0.313,0.198 10 false 2-4 2.219,1.688 2.531,1.885 0.313,0.198 10 false LO 1.49,1.781 1.948,1.979 0.458,0.198 10 false GND 0.083,0.083 0.333,0.25 0.25,0.167 10 false *a
*a Component with harness connected
(to 4 wheel drive control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (LO) - 4 (GND) Ignition switch ON 10.5 to 14 V
5 (HI) - 4 (GND) Ignition switch ON 10.5 to 14 V


If the result is not as specified, replace the 4 wheel drive control ECU(Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL)

If the result is normal, replace the 4wd control switch (Click hereDrivetrain>VF4BM (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH(w/o Combination Switch)>REMOVAL)



b.
C381466C05
2.333,1.708 2.167,1.708 2.167,1.708 2.167,1.208 true 1.604,1.698 1.771,1.698 1.771,1.698 1.771,1.198 true 2.385,1.615 3,1.813 0.615,0.198 10 false ILL+ 1.333,1.615 1.948,1.813 0.615,0.198 10 false ILL- 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a
*a Front view of wire harness connector
(to 4wd Control Switch)


Apply battery voltage between the terminals of the switch, and check the illumination condition of the 4wd control switch .

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 1 (ILL+)
Battery negative (-) → 3 (ILL-)
Illuminates


If the result is not as specified, replace the 4wd control switch.