Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for LED Headlight) › 2017.08–2021.06
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326212 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING (EXT)  LIGHTING SYSTEM(for LED Headlight)  U0242  Lost Communication With Headlamp Control Module "B"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0242 Lost Communication With Headlamp Control Module "B" The No. 1 headlight ECU sub-assembly LH does not receive data from the No. 1 headlight ECU sub-assembly RH for approximately 10 seconds or more.
·

Harness or connector

·

No. 1 headlight ECU sub-assembly LH

·

No. 1 headlight ECU sub-assembly RH


-

WIRING DIAGRAM

E374191E01
0.406,3.313 1.75,3.698 1.344,0.385 10 false A102 5.594,3.292 6.938,3.677 1.344,0.385 10 false A103 5.604,3.438 6.948,3.823 1.344,0.385 10 false No. 1 Headlight ECU Sub-assembly RH 5.865,2.063 6.313,2.292 0.448,0.229 10 false LCH 1.146,2.063 1.594,2.292 0.448,0.229 10 false LCH 1.198,2.604 1.646,2.833 0.448,0.229 10 false LCL 5.865,2.615 6.313,2.844 0.448,0.229 10 false LCL 5.594,2.458 6.042,2.688 0.448,0.229 10 false 21 1.552,2.479 2,2.708 0.448,0.229 10 false 21 1.542,1.938 1.99,2.167 0.448,0.229 10 false 22 5.594,1.906 6.042,2.135 0.448,0.229 10 false 22 5.563,1.198 6.01,1.427 0.448,0.229 10 false 12 5.854,1.323 6.302,1.552 0.448,0.229 10 false GND 5.854,0.688 6.302,0.917 0.448,0.229 10 false IG 5.656,0.625 6.104,0.854 0.448,0.229 10 false 4 2.604,0.688 4.177,0.896 1.573,0.208 10 false from IG NO.4 Relay 4.479,0.917 5.469,1.25 0.99,0.333 10 false ECU-IG NO.3 0.406,3.469 1.75,3.854 1.344,0.385 10 false No. 1 Headlight ECU Sub-assembly LH 0.635,4.354 3.021,4.708 2.385,0.354 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuse for circuits related to this system before performing the follow ingprocedure.

·

If the No. 1 headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>REGISTRATION



PROCEDURE

1.CHECK DTC

b.

Turn the ignition switch to ON and wait for at least 10 seconds or more.


c.

Check for DTCs.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DTC CHECK / CLEAR

OK:

DTC U0242 is not output.



Result:
Proceed to
OK
NG



OK

USE SIMULATION METHOD TO CHECK

NG

2.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - BATTERY AND BODY GROUND)
a.
C300875C97
1.396,0.115 1.844,0.365 0.448,0.25 1.375,1.875 1.188,1.875 1.188,1.875 0.833,1.354 true 0.99,0.333 1.156,0.333 1.156,0.333 1.792,1.167 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.469,0.146 1.896,0.354 0.427,0.208 10 false A103 0.792,0.208 1.26,0.375 0.469,0.167 10 false IG 1.427,1.75 1.896,1.917 0.469,0.167 10 false GND
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly RH)


Disconnect the No. 1 headlight ECU sub-assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A103-4 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A103-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK FOR CAN BUS WIRE (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH CAN MAIN WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FOR CAN BUS WIRE (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH CAN MAIN WIRE)
a.
C300875C98
1.396,0.115 1.844,0.365 0.448,0.25 1.656,1.896 1.823,1.896 1.823,1.896 2.292,1.354 true 1.99,2.094 2.156,2.094 2.156,2.094 2.427,1.344 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.458,0.146 1.885,0.354 0.427,0.208 10 false A102 1.656,1.969 2.125,2.135 0.469,0.167 10 false LCH 1.333,1.792 1.802,1.958 0.469,0.167 10 false LCL
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly LH)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A102-22 (LCH) - A102-21 (LCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A102-22 (LCH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A102-21 (LCL) - +B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A102-22 (LCH) - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A102-21 (LCL) - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

NG

4.CHECK FOR CAN BUS WIRE (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH CAN MAIN WIRE)
4.CHECK FOR CAN BUS WIRE (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH CAN MAIN WIRE)
a.
C300875C99
1.396,0.115 1.844,0.365 0.448,0.25 1.656,1.896 1.823,1.896 1.823,1.896 2.292,1.354 true 1.99,2.094 2.156,2.094 2.156,2.094 2.427,1.344 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.458,0.146 1.885,0.354 0.427,0.208 10 false A103 1.656,1.969 2.125,2.135 0.469,0.167 10 false LCH 1.333,1.792 1.802,1.958 0.469,0.167 10 false LCL
*a Front view of wire harness connector
(to No. 1 Headlight ECU Sub-assembly RH)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A103-22 (LCH) - A103-21 (LCL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A103-22 (LCH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A103-21 (LCL) - +B Cable disconnected from negative (-) battery terminal 200 Ω or higher
A103-22 (LCH) - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
A103-21 (LCL) - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR