Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (for LED Headlight) › from 2017.08
RM27T0E _59 Vehicle Exterior _053747 LIGHTING (EXT) _0326212 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING (EXT)  LIGHTING SYSTEM(for LED Headlight)  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light.

WIRING DIAGRAM

E374187E01
5.354,5.865 7.063,6.26 1.708,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 3.594,5.833 5.25,6.24 1.656,0.406 10 false Driver Side Junction Block Assembly 6.135,3.677 6.708,3.948 0.573,0.271 10 false RFGO 5.802,3.708 6.375,3.979 0.573,0.271 10 false A 5.781,3.51 6.354,3.781 0.573,0.271 10 false 27 4.833,4.385 5.406,4.656 0.573,0.271 10 false TAIL 4.729,4.021 5.302,4.292 0.573,0.271 10 false FOG RR 1.854,3.396 2.76,3.771 0.906,0.375 10 false from Battery 0.5,3.042 2.969,3.385 2.469,0.344 10 false U3 0.479,2.354 1.042,2.625 0.563,0.271 10 false 2 0.469,0.979 1.031,1.25 0.563,0.271 10 false 2 2.125,0.979 2.688,1.25 0.563,0.271 10 false 1 2.125,2.365 2.688,2.635 0.563,0.271 10 false 1 3.26,3.427 4.167,3.802 0.906,0.375 10 false 2K 3.302,3.24 4.208,3.615 0.906,0.375 10 false 1 3.25,0.927 4.156,1.302 0.906,0.375 10 false 11 3.24,1.104 4.146,1.479 0.906,0.375 10 false 2Q 0.542,1.677 2.823,1.906 2.281,0.229 10 false V3 4.813,5.438 5.385,5.708 0.573,0.271 10 false TAIL 3.833,3.573 4.406,3.844 0.573,0.271 10 false FOG RR 5.813,5.125 6.385,5.396 0.573,0.271 10 false A 6.135,5.115 6.708,5.385 0.573,0.271 10 false TRLY 5.781,4.938 6.354,5.208 0.573,0.271 10 false 14 0.302,5.833 2.771,6.177 2.469,0.344 10 false *1: for LHD 0.302,6.177 2.771,6.521 2.469,0.344 10 false *2: for RHD 2.885,1.104 3.792,1.479 0.906,0.375 10 false 2P 2.875,0.917 3.781,1.292 0.906,0.375 10 false 11 2.854,1.313 3.76,1.688 0.906,0.375 10 false *2 3.26,1.323 4.167,1.698 0.906,0.375 10 false *1 0.542,1.833 2.823,2.063 2.281,0.229 10 false Rear Fog Light Assembly LH 0.5,3.177 2.781,3.406 2.281,0.229 10 false Rear Fog Light Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuse for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, perform the Active Test.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for LED Headlight)>DATA LIST / ACTIVE TEST

Main Body
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog lights OFF or ON Light control switch in Tail or Head position.

OK:

Rear fog light relay operates (rear fog lights turn on).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - REAR FOG LIGHT ASSEMBLY AND BATTERY)
2.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - REAR FOG LIGHT ASSEMBLY AND BATTERY)
a.

Disconnect the 2Q*1, 2P*2 and 2K driver side junction block assembly connectors.

*1: for LHD

*2: for RHD



b.

Disconnect the V3 rear fog light assembly LH connector.


c.

Disconnect the U3 rear fog light assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2K-1 - Body ground Always 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
2Q-11 - V3-1 Always Below 1 Ω
2Q-11 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
2P-11 - V3-1 Always Below 1 Ω
2P-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

E377374C01
0.438,0.344 0.938,0.573 0.5,0.229 2.271,0.396 2.771,0.625 0.5,0.229 2.26,0.073 2.76,0.302 0.5,0.229 5.167,0.542 5.667,0.771 0.5,0.229 4.688,0.729 4.927,0.729 4.927,0.729 5.208,1.115 true 5.719,1.51 5.958,1.51 5.958,1.51 6.365,1.125 true 2.844,0.094 3.156,0.25 0.313,0.156 10 false *A 2.854,0.406 3.167,0.563 0.313,0.156 10 false *B 0.115,0.073 0.427,0.229 0.313,0.156 10 false *a 0.604,0.365 0.927,0.563 0.323,0.198 10 false 2K 5.365,0.552 5.677,0.708 0.313,0.156 10 false A 4.281,0.625 4.75,0.833 0.469,0.208 10 false TRLY 5.292,1.406 5.76,1.615 0.469,0.208 10 false RFGO 2.396,0.094 2.865,0.302 0.469,0.208 10 false 2Q 2.417,0.417 2.885,0.625 0.469,0.208 10 false 2P
*A for LHD *B for RHD
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
2Q-11 - Battery negative (-) terminal Battery not connected to 2K-1, A-14 (TRLY) and A-27 (RFGO) Below 1 V
Battery positive (+) → 2K-1
Battery negative (-) → A-14 (TRLY) and A-27 (RFGO)
11 to 14 V

for RHD
Tester Connection Condition Specified Condition
2P-11 - Battery negative (-) terminal Battery not connected to 2K-1, A-14 (TRLY) and A-27 (RFGO) Below 1 V
Battery positive (+) → 2K-1
Battery negative (-) → A-14 (TRLY) and A-27 (RFGO)
11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY